How often should the original spark plugs of Haval H6 be replaced?

1 Answers
WyattLee
07/30/25 4:27am
Haval H6 spark plugs should be replaced every 18 months or 18,000 kilometers, whichever comes first. The original spark plugs for Haval H6 use the Champion RC8PYCBX single platinum model. Under normal maintenance conditions, spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine, so it is recommended to follow the user manual. You can refer to the following standards for maintenance and replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the hood, lift the plastic cover of the engine, remove the high-voltage distributor wires, and mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. When removing them, check for external debris such as leaves or dust and ensure everything is cleaned thoroughly. Place the new spark plugs into the spark plug holes, hand-tighten them a few turns, and then use the socket to tighten them further. Reinstall the removed high-voltage distributor wires according to the firing order and secure the cover plate.
Was this review help?
11
0
Share
More Forum Discussions

How to Determine if a Car Air Conditioner Thermostat is Faulty?

Determine if the car air conditioner thermostat is faulty, causing intermittent cooling in the car air conditioner. Below is an introduction about car parts: 1. Introduction: Car parts are the individual units that make up the entire vehicle and products that serve the car. 2. Identifying authenticity: (1) Check packaging and printing: Genuine parts usually have standardized packaging with uniform specifications and clear, regular printing. (2) Check color and paint: Some original parts have a specific designated color on the surface; if other colors are found, they are likely counterfeit parts. (3) Check appearance and feel: Original parts have clear and regular printing, casting, or markings, while counterfeit products have a rough appearance.
19
5
Share

What is the ground clearance of the Honda XRV?

The ground clearance of the Honda XRV is 130mm when fully loaded and can reach up to 142mm. Below is an introduction to the Honda XRV: 1. The length, width, and height of the Honda XRV are 4328mm, 1772mm, and 1605mm respectively, with a wheelbase of 2610mm. The exterior design of the Honda XRV follows the family style, exuding a strong sense of fashion and sportiness, incorporating many youthful design elements that align more with the aesthetic preferences of younger consumers. 2. The Honda XRV is equipped with two engines: a 1.5L and a 1.5T, paired with two types of transmissions: a 6-speed manual transmission and a CVT continuously variable transmission. The 1.5L engine has a maximum output power of 96 kW, a maximum torque of 155 N·m, a top speed of 192 km/h, a 0-100 km/h acceleration time of 11.1 seconds, and a combined fuel consumption of 6.3L/100km as published by the Ministry of Industry and Information Technology. The 1.5T engine has a maximum output power of 130 kW, a maximum torque of 220 N·m, a top speed of 200 km/h, a 0-100 km/h acceleration time of 8.9 seconds, and a combined fuel consumption of 6.1L/100km as published by the Ministry of Industry and Information Technology.
12
0
Share

How to Deal with Car Noise?

There are four solutions to car noise: 1. Engine noise: The vehicle engine is a source of noise, and its noise varies with engine speed. Solution: Install high-grade sound-absorbing foam materials on the engine cover, which can not only suppress vibrations caused by the hood but also absorb a large amount of noise, with noticeable effects. 2. Tire noise: Tire noise is generated by the friction between the tires and the road surface during high-speed driving. The level of tire noise depends on road and vehicle conditions—the worse the road conditions, the greater the tire noise. Additionally, there is a significant difference between the tire noise produced on asphalt roads and concrete roads. Solution: Tire noise is a type of structural noise, primarily caused by vibrations. The most reasonable solution is vibration control. Adding damping plates along with sound-absorbing pads can effectively reduce road and tire noise. 3. Wind noise: Wind noise occurs when the pressure of oncoming wind exceeds the sealing resistance of the car doors during high-speed driving, entering the cabin. The faster the driving speed, the greater the wind noise. Solution: Install or replace door sealing strips. Since sealing strips are made of rubber, they tend to age over time, leading to reduced sound insulation and sealing effectiveness. 4. Body structure noise: This is mainly influenced by two factors—the vibration transmission method of the body structure and the noise generated by metal components in the body due to internal and external forces. Solution: This issue rarely occurs in new cars. Check whether the screws on body components are loose. Generally, tightening the screws or replacing the parts can resolve the problem.
9
0
Share

What does p030100 misfire detected in cylinder 1 mean?

p030100 misfire detected in cylinder 1 can be caused by the following reasons: 1. Ignition system failure; 2. Fuel delivery failure; 3. Intake manifold or EGR issues; 4. Air leakage in PCV; 5. Mechanical cylinder failure, etc. Below is relevant information about cylinder misfire: 1. Definition: Cylinder misfire refers to the phenomenon where the air-fuel mixture fails to combust properly in the cylinder due to various reasons during engine operation. 2. Action: If the electronic control unit (ECU) detects a misfire that could potentially damage the catalytic converter, the malfunction indicator lamp will flash, and the engine should be shut down immediately in such cases.
9
4
Share

Why can't the thumb shifter be moved?

The reason why the thumb shifter can't be moved is due to severe rusting of the shift cable and housing. Here is an introduction about automotive parts: 1. Introduction: Automotive parts are the individual components that make up the entire vehicle and products that serve the car. 2. Identifying genuine parts: (1) Check packaging and printing: Genuine parts usually have standardized packaging with uniform specifications and clear, regular printing. (2) Check color and paint: Some original parts have specific colors; if other colors are found, they are likely counterfeit. (3) Check appearance and feel: Genuine parts have clear and regular printing or casting marks, while counterfeit products appear rough.
10
3
Share

What Causes the Red Exclamation Mark on the Dashboard?

Red exclamation mark (specifically a circle with an exclamation mark inside parentheses) indicates a warning for the braking system, mainly due to brake system malfunction or low brake fluid level. Solution: Immediate inspection and repair of the braking system are required to avoid accidents. Apart from the red exclamation mark representing brake system issues, other exclamation marks on the car are yellow, indicating general faults, automatic transmission issues, abnormal tire pressure, and lighting faults. Below is a detailed analysis of these four scenarios: General Fault: A triangle with an exclamation mark inside indicates a malfunction in the car's general performance or components and functions. Possible causes include parking sensor failure, fuel cutoff system intervention or malfunction, external light failure, engine oil pressure sensor failure, etc. It is necessary to visit a 4S shop for inspection to identify the source of the fault. Automatic Transmission Fault: A yellow gear with an exclamation mark inside is the automatic transmission warning light, indicating a fault in the transmission or transmission lubricant below the normal range. Transmission oil should be replaced promptly. Abnormal Tire Pressure: A horizontal line under parentheses with an exclamation mark in the middle represents the tire pressure monitoring warning light. This light turns on when the car's tire pressure is too low. Check the tire pressure and restore it to the normal range. Lighting Fault: A yellow bulb with an exclamation mark is the lighting fault indicator, signaling a malfunction in the car's lights. Solution: Visit a 4S shop as soon as possible for inspection and repair, or conduct a self-check, focusing on commonly used bulbs such as turn signals, fog lights, and interior lights to identify the issue.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.