How Often Should the Oil in a Dual-Clutch Transmission Be Changed?

How Many Chances Are There for the Subject Two Driving Test?

For the Subject Two driving test, if the initial attempt is unsuccessful, one retake is allowed. If the applicant does not attend the retake or fails the retake, the current test session is terminated, and the applicant must reschedule the test after ten days. Within the validity period of the driving skill test permit, the number of rescheduled tests for Subject Two and Subject Three (road driving skills) must not exceed five times. If the fifth rescheduled test is still unsuccessful, the passing scores of other previously passed subjects will be invalidated. The full score for Subject Two is 100 points, with evaluation criteria set for failing, deducting 20 points, deducting 10 points, and deducting 5 points. The test is considered passed if the following conditions are met: ① For applicants of large passenger vehicles, tractors, city buses, medium-sized passenger vehicles, and large trucks, a score of 90 or above is required; ② For other vehicle types, a score of 80 or above is required. The test items for large vehicles (A1, A2, A3, B1, B2) include: pole test, hill start and stop, parallel parking, single-plank bridge crossing, curve driving, right-angle turning, narrow gate passing, continuous obstacle crossing, bumpy road driving, narrow road U-turn, as well as simulated highway driving, continuous sharp turns on mountain roads, tunnels, rainy (foggy) conditions, slippery roads, and emergency handling. The test items for small vehicles (C1, C2) include: reversing into a garage, parallel parking, hill start and stop (canceled for C2), right-angle turning, and curve driving (commonly known as the S-curve) as the five mandatory items (some regions also include a sixth item: highway toll card collection).

11

0

Share

What is the emission standard for VI?

VI is the China VI emission standard. When the China VI emission standard was introduced, the country clearly defined the phased implementation of two modes: China VI a and China VI b. Among them, China VI a is equivalent to the transition stage from China V to China VI, while China VI b is the true China VI standard emission. The China VI standard has stricter limit requirements, which are 40% to 50% stricter than those of China V. In addition, unlike the different limits for gasoline and diesel vehicles in the China V stage, the China VI standard adopts the same limit requirements for gasoline and diesel vehicles based on the principle of fuel neutrality. The China VI standard adds requirements for the emission warranty period, stipulating that if there are failures or damages related to emissions within 3 years or 60,000 kilometers, leading to excessive emissions, the automobile manufacturer shall bear all costs for corresponding repairs and replacement of parts to protect the rights and interests of car owners.

2

1

Share

How often should a blue-plate light truck undergo annual inspection?

Batman is an SUV-specific MT tire product under the Atlas brand, designed to tackle the most challenging road conditions. Here is an introduction to Batman tires: 1. Tread and sidewall: The bionic shark fin design in the middle block primarily enhances comfort during low-speed driving. Honestly, the ride feel is not much different from regular tires, and it doesn't produce any additional noise, which is quite a pleasant surprise. 2. Basic data testing: The measured data from left to right are: 14.49mm, 14.52mm, 14.57mm, 14.68mm. Such thick tread patterns are naturally intended to handle various insurmountable terrains. Testing shows that the tread hardness from left to right is 59HA, 63HA, 58HA, 61HA, respectively, with a sidewall hardness of 48HA.

5

1

Share

What is the correct sequence for starting a manual transmission car?

Manual transmission car starting sequence: Press the clutch pedal fully with your left foot, shift the gear lever into first gear, turn on the left turn signal, release the handbrake, gently lift the clutch pedal with your left foot, and slowly raise the left foot until the clutch reaches the half-engaged state, then the vehicle will start moving. Below are precautions for starting a manual car under different conditions: Precautions for starting on flat roads: The most challenging aspect of starting a manual transmission car is coordinating the clutch and accelerator. Find the critical engagement point for the specific gear to avoid stalling due to excessive clutch release or insufficient throttle. While gently lifting the clutch, gradually press the accelerator, then release the handbrake, allowing the car to move forward steadily. Precautions for starting on slopes: First, pull up the handbrake to ensure the car is stably stopped on the slope. Then, gently lift the clutch and slowly apply some throttle.

17

3

Share

What are the symptoms of a slightly blown head gasket?

The symptoms of a slightly blown head gasket are: decreased power, weak vehicle performance, abnormally high engine temperature, poor operation, low coolant level, oil in the coolant, and water in the engine oil. Additionally, after a cold start, open the radiator cap and observe if the coolant is calm. If there is noticeable coolant spilling or spraying out from the radiator filler neck, this indicates a blown head gasket. If the starting system, fuel supply system, and ignition system are all functioning normally but the engine cannot be restarted after being shut down for a long time, the head gasket may be damaged. You can also start the engine and check if water or steam sprays out from the spark plug holes to confirm whether the head gasket is burnt. The head gasket is installed between the cylinder head and the engine block, secured by cylinder head bolts to ensure cylinder sealing and prevent leakage of combustion gases, coolant, and lubricating oil. A blown head gasket can be simply understood as an impact-related failure between the piston and the cylinder liner or the gasket itself.

10

3

Share

Why is water leaking from the car exhaust pipe?

Car exhaust pipe leaks water because: For the engine to work, it must burn fuel, which is gasoline. Gasoline undergoes oxidation reaction and combustion. After complete combustion, carbon dioxide and water are produced. This water is discharged from the exhaust pipe, which also proves that the car's combustion condition is good and is a normal phenomenon. The car exhaust pipe, also known as the tailpipe, is a device designed to reduce vibration and noise, facilitate installation, and extend the life of the exhaust muffler system. It is installed between the engine exhaust manifold and the muffler, making the entire exhaust system flexibly connected. The exhaust pipe is mainly used for light vehicles, micro vehicles, buses, and motorcycles. The structure of the exhaust pipe is a double-layer corrugated pipe covered with a steel wire mesh sleeve, with a clamping ring on the straight sections at both ends. To achieve better noise reduction, the corrugated pipe can be equipped with a telescopic joint or mesh sleeve inside.

15

0

Share

How Often Should the Oil in a Dual-Clutch Transmission Be Changed?

How Many Chances Are There for the Subject Two Driving Test?

What is the emission standard for VI?

How often should a blue-plate light truck undergo annual inspection?

What is the correct sequence for starting a manual transmission car?

What are the symptoms of a slightly blown head gasket?

Why is water leaking from the car exhaust pipe?

What Type of Engine Oil Does the Lynk & Co 01 Use?

How to Use the Battery Correctly?

How to Determine if the Brake Master Cylinder is Faulty?

How to Use an Automatic Transmission Car?