How often should the gear oil of the Xisha be changed?

1 Answers
ChloeFitz
07/30/25 12:42am
The gear oil of the Xisha should be changed every three years or 60,000 kilometers. Gear oil replacement intervals: If synthetic oil is used, replacement is not required within 200,000 kilometers; if mineral oil is used, it should be replaced every 40,000 to 60,000 kilometers. Gear oil mainly refers to the lubricating oil for transmissions and rear axles, primarily serving to lubricate gears and bearings, prevent wear and corrosion, and assist in heat dissipation for the gears. Hazards of not changing transmission oil for a long time: It can cause abnormal wear and severe deterioration of the transmission oil; lead to aging and degradation of the transmission oil, increasing fuel consumption and shortening the transmission's lifespan; result in granulation of the transmission oil, clogging oil passages, damaging the valve body, and affecting system oil pressure and power transmission; cause delayed response and gear shifting impacts in the transmission.
Was this review help?
5
1
Share
More Forum Discussions

What to Do When a Volkswagen Car Key Gets Wet?

If your Volkswagen car key gets wet, follow these steps: 1. Stop using it immediately; 2. Wipe off the water on the surface of the key; 3. Use a screwdriver to open the key cover; 4. Remove the battery and wipe the circuit board; 5. Dry the circuit board and reassemble it. Taking the Volkswagen Magotan 280 as an example, it is a mid-size car with dimensions of 4865mm in length, 1832mm in width, and 1471mm in height, with a wheelbase of 2871mm. The Volkswagen Magotan 280 is equipped with a 1.4T turbocharged engine, delivering a maximum power of 110 kW and a maximum torque of 250 Nm, paired with a 7-speed dual-clutch transmission.
13
3
Share

How to Use Turn Signals?

The method for using turn signals is as follows: 1. When changing lanes while driving, you should first turn on the corresponding turn signal before changing lanes; 2. When making a U-turn, you should turn on the corresponding turn signal and check for any oncoming vehicles before proceeding; 3. When overtaking on a road section without a solid center line marking, you should turn on the left turn signal and sound the horn as a warning; 4. When pulling over to park, first turn on the right turn signal and check the traffic conditions behind and to the right of the vehicle before pulling over; 5. When leaving a parking spot, turn on the left turn signal and check the traffic conditions behind and to the left of the vehicle before merging into the traffic lane.
8
4
Share

How to Inflate and Ignite a Tubeless Tire with Large Gaps?

The method for inflating and igniting a tubeless tire with large gaps is: 1. Use a rapid inflator to direct pressure into the tire gaps for inflation; 2. Spray carburetor cleaner into the tire and ignite the cleaner. Tubeless tire maintenance methods include: 1. Regularly inspect all tires when they are cool; 2. Frequently remove debris from tire treads; 3. Repair punctures promptly; 4. Do not exceed the reasonable speed required by driving conditions; 5. Regularly perform wheel alignment and balancing; 6. Protect tires from sunlight, oil, acid, and hydrocarbon erosion; 7. Rotate tires every 8,000 to 10,000 kilometers.
11
4
Share

How to Open the Front Hood of a Mercedes-Benz E300?

To open the front hood of a Mercedes-Benz E300, follow these steps: 1. Pull the dedicated front hood release lever; 2. Lift the hood by hand. The Mercedes-Benz E300 is a mid-size luxury sedan with the following dimensions: length 4947mm, width 1860mm, height 1470mm, wheelbase 2939mm, and a fuel tank capacity of 66 liters. It is equipped with a 2.0T turbocharged engine that delivers a maximum power of 190 kW and a maximum torque of 370 Nm. The vehicle features rear-wheel drive, multi-link independent suspension on both front and rear, and a 9-speed automatic transmission with manual shift mode.
1
5
Share

What are the solutions for high engine coolant temperature?

The solutions for high engine coolant temperature are: 1. Seal the thermostat; 2. Repair the fan circuit; 3. Replace the radiator thermoswitch; 4. Refill coolant; 5. Clean debris from the water pump. The causes of high engine coolant temperature are: 1. Thermostat not sealing properly; 2. Insufficient thermostat opening; 3. Fan circuit malfunction; 4. Damaged radiator thermoswitch; 5. Insufficient coolant; 6. Clogged water pump. Engine maintenance methods include: 1. Regularly change engine oil and filter; 2. Periodically clean the radiator; 3. Regularly replace air and fuel filters; 4. Maintain good crankcase ventilation; 5. Periodically clean the fuel system.
4
0
Share

What is the solution for the Verna power steering pump air not being fully purged?

The solution for the Verna power steering pump air not being fully purged is: start the engine, turn the steering wheel fully to the left and right for a few seconds each to purge the air. Taking the 2020 Verna as an example, it belongs to the compact car category, with body dimensions of: length 4300mm, width 1705mm, height 1460mm, wheelbase 2570mm, fuel tank capacity 43l, and curb weight 990kg. The 2020 Verna features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.4L naturally aspirated engine, delivering a maximum horsepower of 95PS, maximum power of 70kW, and maximum torque of 132.4Nm, paired with a 5-speed manual transmission.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.