How Often Should the Differential Oil of a Truck Be Changed?

1 Answers
VonKatherine
07/28/25 5:07pm
Truck differential oil should be changed every 40,000 kilometers. Changing the differential oil prevents excessive wear of the vehicle's differential gears, which could lead to differential damage. The steps for changing differential oil are as follows: 1. Lift the vehicle and place a large container underneath to catch the used oil. Use an appropriate screwdriver to remove the inner and outer shells of the transmission. 2. When most of the oil has drained, remove the last oil pan. 3. Remove the oil pan gasket and clean any surrounding stains. If the gaps are not clean enough, use tools and cotton thread to thoroughly clean all the filtered parts of the transmission oil, then reinstall them one by one. 4. Wipe the surfaces of the replacement parts clean, reinstall the cleaned oil pan and gasket, and add the original manufacturer's oil.
Was this review help?
7
4
Share
More Forum Discussions

How to Turn Off the Built-in Navigation in Mercedes-Benz E300L?

You can set it in the additional area of the interface settings. Alternatively, you can use voice control by saying "Cancel navigation" in standard Mandarin to exit the navigation. Below are the specific details about car navigation: 1. Car navigation features the GPS global satellite positioning system. Drivers only need to input the destination into the car navigation system, and the system will automatically calculate the most suitable route based on the electronic map. It will also remind the driver to follow the calculated route during the vehicle's movement (e.g., before turning). 2. The car navigation system mainly consists of two parts: the navigation host and the navigation display terminal. The built-in GPS antenna receives data from at least three of the 24 GPS satellites orbiting the Earth, thereby determining the current position of the car. By matching the position coordinates determined by the GPS satellite signals with the electronic map data, the navigation host can accurately locate the car on the electronic map.
14
2
Share

Does the Golf GTI use the EA888 engine?

The Golf GTI uses the EA888 engine, which is a 2.0-liter turbocharged engine with a maximum power of 220 horsepower and a maximum torque of 350 Nm. The maximum power speed ranges from 4,500 to 6,200 rpm, and the maximum torque speed ranges from 1,500 to 4,400 rpm. This engine features hybrid injection technology and uses an aluminum cylinder head with a cast iron cylinder block. The Golf GTI is a hot hatch model, available in both imported and domestically produced versions. The car's dimensions are 4,296 mm in length, 1,788 mm in width, and 1,471 mm in height, with a wheelbase of 2,636 mm. The Golf GTI's front suspension is a MacPherson strut independent suspension, and the rear suspension is a multi-link independent suspension.
8
4
Share

What does 'sport' mean when it appears on the car?

When 'sport' appears on the car, it refers to a performance-oriented shifting mode set for automatic transmissions. In the S (sport) mode, the transmission can shift freely, but the shifting timing is delayed, allowing the engine to maintain higher RPMs for a longer period. This results in the car operating at lower gears with higher RPMs for an extended duration, thereby delivering greater torque output and acceleration. Another common mode is the P (park) mode, which is a special neutral gear that mechanically locks the transmission output shaft to secure the vehicle. Its function is to act as a parking brake, preventing the vehicle from moving. For practical safety reasons, car manufacturers place the P mode in the first position on the gear shift console and configure internal mechanisms to ensure that the car key can only be removed when the gear shift lever is moved to the P mode. Therefore, the P mode is specifically designed for parking and prolonged stops in automatic transmission vehicles.
19
4
Share

Will there be a warning if the car door is not properly closed?

If the car door is not properly closed, there will be a warning on the dashboard. Door ajar indicator: When a door is not fully closed, an indicator light on the dashboard will illuminate to alert the driver that the door is not closed. The indicator will turn off once the door is properly shut. The dashboard will also display warnings if the engine hood or trunk lid is not closed. Potential damage from slamming car doors: Hinges and latches can be damaged, leading to wear and misalignment; the sound insulation layer can be severely affected, and if the door is damaged, noise levels can increase significantly; doors are prone to aging, and loose hinges and limiters can cause internal components to become loose, such as clips, door lights, and sensor switches.
17
1
Share

Can a vehicle be inspected without handling traffic violations?

Unhandled traffic violations prevent vehicle inspection. All violations must be addressed: Before annual inspection, all traffic violations must be resolved. If a motor vehicle has outstanding violation records, it cannot undergo inspection. Even if the vehicle passes external inspection, traffic authorities will not issue an inspection compliance certificate. Annual inspection can only proceed after all violations are properly handled according to regulations. Motor vehicle violations: Motor vehicle violations refer to acts that contravene the Road Traffic Safety Law and traffic management regulations. Checking for such violations is called motor vehicle violation inquiry. The revised "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" (Ministry of Public Security Order No. 123), known as "the strictest traffic regulations in history," came into effect on January 1, 2013.
1
1
Share

What are the symptoms of a faulty canister purge solenoid valve?

Symptoms of a faulty canister purge solenoid valve: 1. Abnormal noises while driving, specifically a "clicking" sound heard when the engine is not idling; 2. Increased fuel consumption with a noticeable gasoline odor inside the car; 3. Difficulty starting the engine, frequent stalling, often requiring a second attempt to start, and the engine easily dying again after starting; 4. Erratic engine idling and poor acceleration. The canister purge solenoid valve is a device installed in cars or motorcycles to reduce air pollution caused by fuel vapor emissions while improving fuel efficiency. Method to determine if the canister purge solenoid valve is faulty: After disconnecting the hose from the canister purge solenoid valve, wait for the solenoid valve to activate, then partially block the valve with your hand. If you can feel the solenoid valve continuously sucking air or not reacting at all, it indicates the solenoid valve is damaged.
19
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.