···
Log in / Register

How often should the clutch of a underbone motorcycle be adjusted?

1 Answers
VonStella
07/28/25 7:24am
The clutch plates of an underbone motorcycle generally need to be replaced every 40,000 kilometers or approximately every 2 years. Introduction to clutch plates: Clutch plates are wear-prone components in the driving system of motor vehicles and are commonly used parts in mechanical transmissions, allowing the transmission system to be separated or connected as needed. Typical clutch plates include: Release lever, release lever support column, swing pin, release sleeve, release bearing, clutch pedal, etc. Motorcycles are powered by gasoline engines and are two or three-wheeled vehicles steered by handlebars, widely used for patrol, passenger and cargo transportation, etc. Motorcycles are categorized into street bikes, road racing motorcycles, off-road motorcycles, cruisers, touring bikes, etc.
Was this review help?
6
3
Share
More Forum Discussions

How to Adjust the Steering Wheel Weight of Camry?

First, locate the adjustment lever under the steering wheel, then press the lever down to its lowest position. Next, move the steering wheel up or down, using the instrument panel as a reference. Once adjusted, secure the lever back in place. Ensure the lever is fully closed and check the steering wheel's stability by moving it up and down.
2
5
Share

How to Turn on the Air Conditioning in a Mercedes-Benz E300L?

Mercedes-Benz E300L's center console uses mechanical buttons. After getting in the car, observe the dashboard to locate the corresponding mechanical buttons. Press the button to directly turn on the air conditioning defogging and heating functions.
17
5
Share

How to Adjust Seat Belt Height Without Height Adjustment Function?

First, locate the seat belt adjustment button on the side of the vehicle seat. Then, press the button downward by hand to adjust the seat belt height. Moving it downward will lower the seat belt position, while pushing it upward will raise the seat belt position.
16
3
Share

How to Determine if a Car Radiator Cap is Damaged?

Reduced circulation capacity, leakage, or abnormal noises can all indicate whether the radiator cap is damaged. Leakage issues are relatively easy to detect. Minor leaks will leave traces at the water pump vent, while significant leaks can be directly observed through water temperature and the ground under the chassis.
1
1
Share

How to Remove and Install the Rearview Mirror Ball Joint?

First, handle the rearview mirror lens by pressing the head of the lens with your hand to lift the tail, then grab the tail with your hand and pull it outward forcefully to remove the lens. Unscrew the screws located at the edge, the bottom of the rearview mirror, and the hidden positions. Install the replacement rearview mirror.
20
1
Share

Reasons for Diesel Engine Fuel Injector Not Spraying Fuel

Injector failures are primarily caused by needle valve issues due to contaminants in the diesel engine. The main reason is that the injector tip in the combustion chamber is exposed to prolonged high-temperature and high-pressure conditions. Below are the causes and solutions: 1. Poor injector atomization: When injection pressure is too low, nozzle holes are worn with carbon deposits, or spring end faces are worn with reduced tension, the injector may open prematurely and close late, resulting in poor fuel atomization. For single-cylinder diesel engines, this prevents operation; for multi-cylinder engines, it causes power loss, black exhaust smoke, and abnormal engine noise. Additionally, oversized diesel droplets that fail to combust completely may flow down cylinder walls into the oil pan, raising oil levels, reducing viscosity, worsening lubrication, and potentially causing bearing seizure or cylinder scoring. Solution: Disassemble, clean, inspect, and recalibrate the injector. 2. Damaged injector return line: When needle valve pairs are severely worn or the needle valve body fits loosely with the injector housing, return fuel flow increases significantly (up to 0.1-0.3kg/h). A damaged or missing return line wastes this fuel. The return line must be intact and sealed to allow fuel to flow back to the tank. If connected to the diesel filter, its end should have a check valve to prevent backflow.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.