How often should the antifreeze be replaced in the Envision?

1 Answers
LeMadelyn
07/30/25 1:40am
The replacement interval for the antifreeze in the Envision is generally every 2 years or within the range of 40,000 to 60,000 kilometers. Expired antifreeze can cause cylinder corrosion, and in severe cases, it may even cause significant damage to the engine. The antifreeze filler cap is located in the engine compartment near the cooling fan. Simply unscrew the cap to add new coolant. For routine maintenance, it is essential to check whether the fluid level is between the max and min marks. If the level drops significantly, there may be a coolant leak, and the vehicle should be taken to a repair shop for inspection. Coolant consists of three components: water, antifreeze, and additives. It prevents the coolant from freezing and cracking the radiator or damaging the engine cylinder block during cold weather when the vehicle is parked. Additionally, it primarily aids in engine cooling, ensuring the engine operates at the correct temperature for optimal performance and preventing damage due to overheating. Typically, coolant should be replaced every 2 years, though some long-life coolants can last 4-5 years before needing replacement.
Was this review help?
19
1
Share
More Forum Discussions

What is the actual fuel consumption of the 9th generation Accord 2.4?

The 9th generation Accord 2.4L has three models, including the 2013 Accord 2.4L-PE, SE, and LX, all equipped with a 179-horsepower engine. The NEDC fuel consumption is 8.7L per 100 kilometers. The actual fuel consumption of the 9th generation Accord 2.4 is 8.2L per 100 kilometers. A car's fuel consumption mainly depends on engine technology, transmission gear ratio, the car's aerodynamic drag coefficient, and the driver's driving habits. Generally, the engine displacement has a certain impact on a car's fuel consumption, but this impact is a fixed value. Therefore, the engine displacement does not significantly affect fuel consumption; external factors have a greater influence. A car's fuel consumption is closely related to the driver's driving habits. If the driver frequently engages in aggressive driving, such as rapid acceleration or sudden braking, it will affect the car's fuel consumption. Statistics show that incorrect driving habits can increase fuel consumption by 5-30%. Fuel consumption is also directly related to tire pressure. For models without a tire pressure monitoring display, many owners tend to overlook the importance of tire pressure. When the tire pressure is too high or too low, the car's fuel consumption will increase. The road conditions also affect fuel consumption. If the car frequently travels on poor road conditions, the engine load increases, leading to higher fuel consumption.
12
0
Share

How to Renew an Expiring Driver's License?

Motor vehicle drivers should apply for license renewal at the vehicle management office of the license issuing authority within 90 days before the expiration of their current driver's license. Documents required for renewal: Bring two copies of ID card, two recent 1-inch bareheaded color photos, original ID card, original driver's license, and a medical examination certificate from a county-level or above hospital (free physical examination is also available at the vehicle management office). License renewal and inspection must meet the following conditions: Holders of large passenger vehicle, tractor, city bus, medium passenger vehicle, or large truck driver's licenses must have no demerit points in the current scoring cycle, or holders of other permitted vehicle type licenses must have less than 12 demerit points in the current scoring cycle. Holders of large passenger vehicle, tractor, city bus, medium passenger vehicle, or large truck driver's licenses with demerit points in a scoring cycle, and holders of other permitted vehicle type licenses who have caused a fatal traffic accident with equal or greater responsibility without having their driver's license revoked, must have completed the inspection education; The applicant must have no pending road traffic safety violations or traffic accidents; The applicant's physical condition must meet the driving license requirements; The driver's license must not be seized, detained, temporarily suspended, revoked, canceled, or annulled by law.
20
3
Share

What is the method for inspecting a cylinder?

The method for inspecting a cylinder is: 1. Measure the cylinder pressure by starting the engine and running it until it reaches normal operating temperature, then remove the air filter; 2. Clean the dirt around the spark plug, remove the spark plug, and ensure the throttle is fully open; 3. Insert the tapered rubber tip of a specialized cylinder pressure gauge into the spark plug hole of the cylinder being measured; 4. Measure the cylinder leakage by placing the intake and exhaust valves of the cylinder being tested at the top dead center position of the compression stroke while the engine is stationary, then use a cylinder leakage tester to check if the pressure reaches the specified value; 5. Throttle comparison method: when the engine is running, increase the throttle, and if a continuous knocking sound is heard from the crankcase, it indicates that the cylinder wall is scratched, causing gas to leak into the crankcase during compression and combustion.
3
1
Share

Is a Car Considered a Total Loss After Replacing the Door?

Replacing a car door does not necessarily mean the vehicle is a total loss. It could also be due to damage to internal components of the door that required replacement. Car doors are not considered wear-and-tear parts. If a car door is replaced, it might be because of a collision that caused severe deformation, making repairs unfeasible and necessitating a full replacement. Alternatively, the door might have been replaced due to a malfunction, which does not classify the car as a total loss. Car doors serve as entry and exit points for drivers and passengers, block external disturbances, provide some protection against side impacts, and contribute to the vehicle's aesthetics. The quality of a car door is primarily reflected in its crash resistance, sealing performance, ease of opening and closing, and other functional indicators. Crash resistance is especially critical because side impacts have minimal buffer distance, posing a high risk of injury to occupants.
3
3
Share

Why is the Lamando called 'Spicy Steamed Bun'?

This is actually a playful nickname given by some car enthusiasts. The English name of the Volkswagen Lamando is 'lamando', which sounds somewhat similar to 'spicy steamed bun' in Chinese, hence many people refer to the Lamando as 'spicy steamed bun'. Relevant information about the Lamando is as follows: 1. Exterior: The diving and expanding front face features two chrome decorations on the upper grille, seamlessly connected with the chrome headlight brows; the front bumper paired with the lower grille extends horizontally to both sides, creating a natural and impactful look. The sharp LED daytime running lights, with their integrated and fierce design, enhance daytime visibility, appearing clear, distinct, and well-arranged, exuding an undeniable aura. 2. Interior: 20 dazzling ambient lights, including 20 white ambient lights, are distributed in the front and rear footwells, inner door handles, armrests, storage slots, and decorative strips on all four doors, with brightness adjustable via the MIB system to create a mysterious ambiance. The luxurious perforated genuine leather sports seats naturally conform to the human body, wrapped in high-quality cowhide and treated for high-temperature wear resistance; the front seats feature added sporty side bolsters for enhanced support. The leather multifunction steering wheel offers height adjustment, with its standard aluminum-magnesium alloy frame being lightweight yet sturdy; multifunction buttons significantly improve safety and convenience. 3. Powertrain: The new EA888 TSI engine incorporates innovative integrated turbocharging technology, direct fuel injection, and variable valve timing, maximizing energy efficiency, delivering high-performance power output with ultra-low fuel consumption.
5
5
Share

What brand is the transmission of the eighth-generation Camry?

The transmission of the eighth-generation Camry is Toyota's Direct Shift-CVT transmission. The body dimensions of the eighth-generation Camry are 4885mm in length, 1840mm in width, and 1455mm in height, with a wheelbase of 2825mm and a fuel tank capacity of 60 liters. The eighth-generation Camry is equipped with a new 2.5L Dynamic Force Engine, delivering a maximum output power of 154kW and a maximum torque of 250Nm. The advantages of the eighth-generation Camry include its elegant appearance, user-friendly features, improved electric seats and sound system, a pleasing dark blue dashboard ambiance, practical sunshades that enhance its class, useful headlight washers, and excellent acceleration performance.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.