How Often Should Mercedes-Benz Antifreeze Be Replaced?

1 Answers
MacLucille
07/29/25 9:26am
Mercedes-Benz vehicle antifreeze generally needs to be replaced every 2 years or 40,000 kilometers. This is just a reference interval. For commercial vehicles with higher mileage, the replacement cycle should be shorter. Since driving conditions vary for each vehicle, the actual replacement schedule should be determined based on usage. Regularly check the antifreeze condition—if levels are low, replenish promptly. If suspended particles, sediment, or discoloration are observed, replace the antifreeze immediately and flush the system. Antifreeze Replacement Procedure: Before a complete antifreeze replacement, conduct a thorough inspection for leaks or cracks in all hoses, with special attention to the five-way connector pipe (named for its five connection points distributing antifreeze to different parts of the vehicle). If leaks are found at this component, replace the hose or reseal the connections as needed. Drain the old antifreeze, then flush the channels with clean water. Fill the coolant reservoir with water and let it circulate continuously through the engine cooling system. Idle the engine for 3-5 minutes to facilitate circulation. Initially, the drained water may appear slightly pink; continue flushing until the outflow runs clear. Remember to disconnect the heater hose and drain the heater core completely. Approximately one hour after draining, pour new antifreeze into the radiator hose for rapid filling. Then add another batch to the reservoir until nearly full. Run the engine for about 10 minutes—as air escapes from the system, the fluid level will drop. Top up to the "MAXT" mark on the reservoir.
Was this review help?
9
4
Share
More Forum Discussions

How to Connect Bluetooth to Play Music in Haval F7?

On the main menu interface, touch the Bluetooth button to switch to the Bluetooth interface. Touch the 'Enable Detection' button to activate this function, then use your phone to search for the Bluetooth name of this system and proceed with Bluetooth pairing. Touch the search button, and the found Bluetooth devices will be displayed below. Touch the name of the Bluetooth device to proceed with Bluetooth pairing.
5
5
Share

Where Are the Brake and Accelerator Pedals Located in a Tesla?

Tesla's brake and accelerator pedals are located beneath the steering wheel in the driver's cabin. Similar to conventional automatic transmission vehicles, there are two pedals: one for braking and one for acceleration. The left pedal is the brake, while the right one is the accelerator. However, as a new energy electric vehicle, Tesla employs a "one-pedal" driving mode. This does not mean Tesla has only one pedal; the brake pedal still exists, but the one-pedal mode incorporates regenerative braking functionality. Method for pressing the accelerator: Place the heel of your right foot on the floor of the driver's cabin as a pivot point. Gently press the accelerator with the ball of your foot, using ankle flexion to apply or release pressure. Key points for pressing the accelerator: Press lightly and release smoothly, accelerate linearly, apply force gently, avoid sudden movements, use toe control, and prevent jerking. Key points for releasing the accelerator: Keep the heel stationary and lift the toes.
13
5
Share

Can Tesla Rear-Wheel Drive Vehicles Be Driven in Snow?

Tesla rear-wheel drive vehicles can be driven in snow. However, it is recommended to switch to snow tires in winter, otherwise, rear-wheel drive cars are prone to skidding. Rear-wheel drive vehicles have greater driving force and faster acceleration, but on wet or snowy roads, they are more susceptible to skidding. As long as you avoid sudden acceleration and apply the throttle gently, skidding can be prevented. Introduction to Starting in Snow: Most rear-wheel drive vehicles are equipped with traction control systems. Drivers can activate the traction control, switch the automatic transmission to manual mode, and start in second gear. This reduces the driving force and usually allows for a smooth start. Safety Awareness is Key: Whether it's front-wheel drive or rear-wheel drive, no vehicle is absolutely safe. The most important factors are the driver's safety awareness and driving habits. These become even more critical when driving in rain or snow. Check Your Tires: In rainy or snowy conditions, the depth of the tire tread plays a crucial role in preventing skidding. Always check your tires before heading out to avoid skidding caused by worn-out tires, which can threaten driving safety.
10
3
Share

How to Deal with Odors in an Old Car?

Here are specific methods to remove odors from an old car: 1. Ventilation and Sunlight: Use ventilation and sunlight to eliminate odors inside the car. Park the car in a dry, well-ventilated area for airing, and avoid parking in damp places as it can affect the car's lifespan. 2. Place Grapefruit or Orange Peels: Place grapefruit or orange peels inside the car to remove odors. These fruit peels have strong odor-absorbing capabilities, so they not only produce a fresh fragrance but also absorb unpleasant smells in the car. 3. Use Activated Charcoal Bags: Use activated charcoal bags to eliminate odors inside the car. Activated charcoal has a powerful odor-absorbing effect and can effectively remove formaldehyde and other odors.
16
4
Share

What is the DPF regeneration treatment method for diesel vehicles?

Continue driving normally until the particulate matter treatment is completed, and the DPF indicator light will automatically turn off. The DPF yellow indicator light will flash, and once the particulate matter treatment is completed, the indicator light will automatically turn off. If the yellow indicator light remains steadily lit, wait for 15-30 minutes. The extinguishing of the indicator light signifies the completion of particulate matter treatment.
2
4
Share

What does 'trip' mean on the dashboard?

The 'trip' on the car dashboard is called the trip meter (Trip). The trip meter allows users to calculate the kilometers traveled for each trip and can be reset to zero by long-pressing the clear button. The trip meter (Trip) is used to randomly measure the mileage from point A to point B. Here is a detailed introduction to the trip meter (trip): 1. The smallest unit of the trip meter (trip) is 0.1 kilometers. The basic calculation method is the fuel consumption per 100 kilometers, which is also a parameter provided by the manufacturer. It is calculated by dividing the actual fuel consumption by the actual mileage traveled. The total mileage calculates the overall distance traveled by the vehicle, which cannot be cleared by ordinary methods. 2. By recording the trip mileage on the dashboard, it is very convenient to calculate the fuel consumption per 100 kilometers. Moreover, it can be reset to zero after each trip. This is where the 'reset' button next to it comes into play. Literally translated, it means 'reset,' and its function is to reset the trip meter on the car dashboard. 3. How to calculate the vehicle's fuel consumption: When filling up the tank for the first time, use the reset button to clear the trip meter, then drive normally to accumulate mileage. When refueling next time, the current mileage traveled (referred to as B) is the amount of fuel used (referred to as A, under the premise of filling up the tank). Then, the amount of fuel used (A) ÷ the current mileage traveled (B) = actual fuel consumption.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.