How Often Should a Sedan Be Serviced?

1 Answers
VanTucker
07/29/25 7:04pm
Sedans should undergo minor maintenance every six months or 5,000 kilometers, and major maintenance every two years or 20,000 kilometers. The main tasks of minor maintenance include changing the engine oil and oil filter, checking the antifreeze, and inspecting the condition and wear of lights, horns, and brake pads. Car maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain parts of the vehicle, also known as car servicing. The purpose of car maintenance is to keep the vehicle clean, ensure normal technical conditions, eliminate potential hazards, prevent faults, slow down the deterioration process, and extend the service life.
Was this review help?
4
0
Share
More Forum Discussions

Should a cracked front bumper be repaired?

The cracked front bumper should be repaired. The front bumper is made of plastic, known as a plastic bumper. Its outer panel and cushioning material are made of plastic, while the crossbeam is formed from cold-rolled sheet metal approximately 1.5mm thick, pressed into a U-shaped channel. The outer panel and cushioning material are attached to the crossbeam, which is then bolted to the vehicle's frame rails. The plastic used in the bumper consists of polyester and polypropylene materials, manufactured through injection molding. In terms of safety, the plastic bumper provides cushioning during low-speed collisions, protecting both the front and rear of the vehicle, as well as pedestrians in the event of an accident. To minimize injury to occupants during side-impact collisions, many cars are equipped with door bumpers to enhance door impact resistance.
10
3
Share

Where is the Buick Excelle fuel filter located?

The Buick Excelle fuel filter is located next to the activated carbon canister of the fuel filter element, near the right rear wheel. It can be seen after lifting the vehicle. The replacement method for the fuel filter is as follows: 1. Release the residual pressure in the fuel system; 2. Remove the grounding wire near the fuel filter element; 3. Place a container under the filter; 4. Pull out the fuel inlet pipe and then remove the adjacent fuel outlet pipe; 5. Remove the old fuel filter element to complete the replacement. Precautions for replacing the fuel filter element include: 1. Ensure the overall sealing of the air filter and cabin air filter; 2. Use the gasoline grade specified by the vehicle manufacturer. The fuel filter, also known as the fuel strainer, functions to remove iron oxide, dust, and solid impurities from the fuel, preventing fuel system blockages, reducing mechanical wear, ensuring stable engine operation, and improving reliability.
3
2
Share

What is the reasonable engine RPM for shifting gears?

Common vehicles usually shift gears appropriately at 2000-3000 RPM. It is advisable to shift gears when the engine reaches the following RPM ranges: 1. First gear start: Engine RPM around 1000-1500, vehicle speed at 10 km/h, then shift to second gear. 2. Second gear: Engine RPM around 1500-2000, vehicle speed reaching 30 km/h, then release the throttle and shift to third gear. 3. Third gear: Engine RPM around 1500-2000, vehicle speed reaching 40 km/h, then release the throttle and shift to fourth gear. 4. Fourth gear: Engine RPM around 1500-2000, vehicle speed reaching 50-70 km/h, then release the throttle and shift to fifth gear. 5. Fifth gear: Engine RPM around 1500-3000, vehicle speed reaching 80-120 km/h. If there are additional gears, continue upshifting based on the pattern and actual feel.
4
4
Share

What are the effects of excessively high engine oil viscosity on a car?

Effects of high-viscosity engine oil on a car: 1. Reduction in engine effective power: High oil viscosity increases the crankshaft's oil stirring resistance, leading to greater internal power loss in the engine. 2. Difficulty in ignition at low RPM: High oil viscosity requires more torque for crankshaft rotation during cold starts, resulting in lower RPM and difficulty in ignition. 3. Poor filter cleaning performance: High oil viscosity slows down circulation speed, reducing the number of passes through the filter and hindering timely removal of wear debris from friction surfaces. 4. Inferior cooling effect: Poor oil flow and slower circulation decrease the rate of heat removal from friction surfaces, resulting in poorer cooling performance and increased risk of engine overheating. 5. Higher carbon residue: High-viscosity oil tends to have larger carbon residue particles and higher solidification points, which can easily clog oil passages.
7
4
Share

How to Use a Diesel Heater?

Diesel heaters can be used directly by turning them on. Here is some relevant information about diesel heaters: 1. Working Principle: The main motor of the heater drives the plunger oil pump, combustion fan, and atomizer to rotate. The oil pump delivers the sucked fuel to the atomizer through the fuel pipeline. The atomizer atomizes the fuel through centrifugal force and mixes it with the air sucked in by the combustion fan in the main combustion chamber, where it is ignited by the hot glow plug. 2. Purpose: Mainly used for preheating the engine in winter and providing heating for truck cabins or passenger compartments. 3. Maintenance Method: After the heater has been running for a period of time, the ignition plug should be unscrewed to clean carbon deposits. If the ignition plug wire is burnt out, it should be removed and replaced with a new one. If excessive carbon deposits cause a decrease in thermal efficiency, the carbon deposits on the inner wall of the water jacket, the cooling fins, and the combustion chamber should be cleaned.
6
3
Share

How to check if ETC has been processed?

Vehicle owners can bring their ID card, driving license and other documents to the ETC service outlet and consult the staff to check whether their car has ETC. The significance of ETC processing is as follows: 1. The bank's application procedures and formalities for ETC special channels are strict. By collecting ETC information from toll stations, the scope of searching for vehicles with electronic tags can be narrowed. 2. The website interactive service information of the fully automatic electronic toll collection system. It is suitable for comprehensive operation information such as highway incident detection, congestion prediction and operation time prediction, management information, planning and construction information, and even the release of induction information, which can feedback customer information and user integrity. 3. The fully automatic electronic toll collection system can be combined with GPS and GIS. While comprehensively improving the efficiency and level of highway transportation management and services, the dynamic whereabouts of customers of the fully automatic electronic toll collection system can be found. 4. By tracking bank consumption information, customers' consumption records can be mastered, which is conducive to finding clues in investigation cases.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.