How often should a private car undergo annual inspection after six years?

2 Answers
LaAaron
07/29/25 4:28pm
After the implementation of the new vehicle inspection regulations, cars between 6 and 10 years old must undergo inspection every 2 years. At the 6th and 8th year, the vehicle must be tested on the inspection line. For private cars older than 10 years, the original inspection cycle still applies, meaning cars between 10 and 15 years old must be inspected once a year, and those older than 15 years must be inspected every six months. The details are as follows: 1. Exhaust emission test: During the annual inspection, the vehicle's exhaust emissions will be checked for compliance, specifically the oxygen sensor and the three-way catalytic converter. Their optimal operating temperature is between 400 to 800 degrees Celsius, so it is recommended that owners warm up the vehicle in the external inspection area before the exhaust emission test to increase the pass rate. 2. Clean the vehicle body: Before the annual inspection, owners should clean the vehicle body in advance. Cleaning the vehicle body, engine compartment, and chassis beforehand can make it easier for the inspectors and help pass the inspection.
Was this review help?
9
3
Share
SaraLynn
08/14/25 5:30am
I just passed the six-year vehicle inspection threshold, and now it's an annual check, which is quite regular. Before the last inspection, I specifically went to the auto repair shop to have the brake pads and lights checked, and it passed in one go, saving a lot of time. Actually, the inspection isn't that scary—it's mainly for our safety, especially since parts on older cars are prone to wear. I recommend not waiting until it's overdue; besides the fine, you might even get points deducted. Booking an appointment with the service center early is much more convenient. Pay attention to any unusual noises or light issues while driving to avoid last-minute hassles. Safety first, bro.
Was this review help?
1
2
Share
Expand All
More Forum Discussions

What are the tire specifications for the Audi A4?

The domestic version of the Audi A4 comes with two tire specifications: 225/50r17 and 245/40r18, while the imported version is equipped with 245/45r18 tires. Below is an introduction to the Audi A4: 1. In terms of powertrain, the Audi A4 comes standard with Audi's patented Quattro all-wheel-drive system, providing the vehicle with double the traction. 2. During steering or braking, the system automatically, accurately, and timely distributes the ground force to each wheel. Additional information: 1. The FAW Audi A4 is sold in three displacement options: 1.8, 2.4, and 3.0. 2. Among them, the 1.8T is available in four variants, the 2.4 displacement in three variants, and the 3.0 displacement in only one variant.
16
2
Share

How often should the gear oil of a scooter be changed?

The replacement cycle for scooter gear oil is between 6000 to 10000 kilometers. Unlike engine oil, gear oil does not require frequent changes. Here are the daily maintenance methods for motorcycles: 1. During the break-in period, keep the motorcycle idle speed at 100 RPM. 2. Match the motorcycle gear with the corresponding speed. 3. When you need to brake due to an upcoming situation, release the throttle, step on the rear brake with your right foot, and gently apply the front brake with your right hand. 4. Regularly inspect the spark plugs. 5. When installing a new spark plug, hand-tighten it until it doesn't move, then use a spark plug socket to tighten it an additional quarter to half a turn. 6. Regularly lubricate the chain.
19
4
Share

How much horsepower can the Audi A4L be tuned to?

If we're talking about ECU tuning, it generally can increase the power by about 10%. The original 190PS horsepower of the Audi A4L can be tuned up to 250PS. Introduction to horsepower: Horsepower is a unit of power, with the international unit of power being the watt. People often see horsepower used in car power ratings, for example, a certain car's maximum power is 130 horsepower. When maximum power occurs: For family cars, the perfect engine should have maximum torque at very low RPMs, while maximum power should appear at relatively higher RPMs.
7
4
Share

Where is the wiper fuse located in a BMW 5 Series?

BMW 5 Series fuse box is located inside the glove compartment on the passenger side. After opening the glove compartment, remove the interior trim panel to access the fuse box. There is also another fuse box located on the side of the trunk. Steps to replace a fuse: Locate the corresponding position of the fuse box, then carefully pry open the cover using a screwdriver or other tools. On the inner side of the cover, you can find the corresponding component fuse based on the information provided. When replacing with a new fuse, ensure that parameters such as current match those of the original fuse. Important notes regarding fuses: Installing a fuse with a current rating higher than specified can easily cause component overload and damage. Never attempt to repair a fuse that has already been damaged.
3
1
Share

Where is the key insertion point for Volkswagen cars?

Volkswagen's door keyhole is located under the lock cover at the end of the door handle. To access the keyhole, you need to open the lock cover at the end of the door handle. When the remote key fails: First, pry open the lock cover, then insert the mechanical key to unlock the door. This allows the owner to open the door even without the smart key. When reinstalling the lock cover, be sure to pull the door handle outward before installation. Reason for hiding the keyhole: Designers concealed the keyhole for aesthetic purposes. This design is actually more practical than an exposed keyhole, as it prevents dirt from entering the keyhole while maintaining a clean and stylish appearance.
17
1
Share

What is the proportion of high-strength steel in Geely Emgrand?

Emgrand adopts a cage-type safety body with over 59% high-strength steel content. While enhancing overall strength to ensure ample space, it also incorporates Geely's unique, industry-leading "Safety Identification Circle", making it the most outstanding model in terms of safety coefficient within its class and even surpassing higher-class products. Definition of high-strength steel: It varies according to the degree of technological advancement required by the era. Generally speaking, alloy steel with a yield strength above 1370MPa (140kgf/mm) and tensile strength above 1620MPa (165kgf/mm) is called ultra-high-strength steel. Standards for high-strength steel: There are numerous international standards for high-strength steel, with just unified international standards including both "ISO" and "CEN". Almost every major steel-producing country has its own national standards.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.