How Much Power Does 1.5T Equivalent to in Liters?

1 Answers
DelAyla
07/29/25 11:54pm
1.5T is equivalent to the power of 1.5L, where L represents the unit, and the displacement of a car is denoted by L, which stands for volume and exhaust capacity. 1.5T refers to adding a turbocharger to a 1.5L naturally aspirated engine, with performance comparable to 1.8T and fuel consumption similar to 1.6T. The biggest advantage of turbocharging is that it can significantly increase the engine's power and torque without increasing the engine displacement, with an improvement rate generally around 30%. A turbocharged engine is one that relies on a turbocharger to increase the intake air volume. A turbocharger is essentially an air compressor. When the engine speed increases, the exhaust speed and turbo speed also accelerate, increasing the air compression level and, consequently, the engine's intake air volume, which in turn can boost the engine's output power. When an engine is equipped with a turbocharger, its maximum output power can increase by about 40% or even more compared to when it is not equipped with one.
Was this review help?
4
3
Share
More Forum Discussions

What is the correct procedure when a vehicle rolls over?

When a vehicle suddenly rolls over, the driver should firmly grip the steering wheel with both hands, hook their feet onto the pedals, and press their back tightly against the seat backrest to stabilize their body and avoid injuries from impacts inside the vehicle. Additionally, care should be taken to prevent being crushed due to vehicle deformation. If the vehicle continues rolling into a deep ditch, the driver should quickly move their body to the lower front of the seat, hold onto the steering wheel or other stable parts to secure themselves, and avoid injury from rolling. Below are some driving precautions: 1. Check mirrors: Always use turn signals and slow down when turning or changing lanes; always check the mirrors before turning. Left turns primarily require checking the left mirror, right turns the right mirror, and both turns should involve checking the interior rearview mirror. 2. Avoid fixating on the front of the vehicle: When driving on clear roads, look straight ahead about 100 meters, not just at the immediate front of the vehicle. 3. Depress the clutch: Generally, when decelerating at speeds above 40 km/h, there's no need to depress the clutch immediately; wait until the speed drops to around 20 km/h before doing so. 4. Steering: Turn the wheel slowly for high-speed turns and quickly for low-speed turns.
13
4
Share

What are the new regulations for annual inspection of family 7-seater vehicles?

New regulations for vehicle annual inspection: Starting from November 20, 2020, non-operational small and mini passenger vehicles with 7-9 seats (excluding minivans) within 6 years are included in the exemption range; for non-operational small and mini passenger vehicles (excluding minivans) over 6 years but under 10 years, the inspection cycle is relaxed from once a year to once every two years, meaning private cars only need to undergo on-site inspections twice within 10 years, specifically in the 6th and 8th years. Content of the annual inspection: Check whether the engine, chassis, body, and their auxiliary equipment are clean, complete, and effective, whether the paint surface is uniform and aesthetically pleasing, whether the main assemblies have been replaced, and whether they match the initial inspection records; Test whether the vehicle's braking performance, steering control, lights, exhaust, and other safety performance meet the requirements of the "Technical Conditions for Safe Operation of Motor Vehicles"; Check whether the vehicle has been modified, remodeled, or altered, whether the driving license, license plate, and all records in the vehicle file match the actual condition of the vehicle, whether there are any changes, and whether the approval and alteration procedures have been completed; Check whether the license plate, driving license, and the enlarged license plate characters printed on the vehicle are damaged, altered, or unclear, and whether they need to be replaced; Check whether large vehicles have the unit name or the name of the street, township, or town where the vehicle is located and the maximum seating capacity in the driver's cabin printed in imitation Song font on both sides of the door as required; Check whether the rear panel of trucks (including the rear panel of trailers) has the license plate number enlarged 2-3 times printed on the outside as required, and whether the sides of the doors of individual or joint-operation vehicles have the word "individual" printed on them; the characters must be clear, and unit codes or other patterns are not allowed (special cases require approval from the vehicle management office).
13
2
Share

How to Deal with the FI Light On in GSX250F1?

The FI light on the GW250 instrument panel indicates a malfunction in the fuel injection system. You need to visit an after-sales service center to read the fault code based on the blinking pattern of the indicator light to determine the cause of the issue. The specific reasons are as follows: 1. Electronic component failure: This refers to a situation where an electronic component fails to function properly due to internal circuit or component issues such as short circuits, open circuits, burnout, breakdown, or failure. 2. Mechanical failure of electronic components: Many electronic components in the fuel injection engine control system contain mechanical parts, such as the core of a solenoid valve or the rotor and vanes of an electric fuel pump. Failures caused by jamming, breakage, or deformation of these mechanical parts that prevent the electronic components from functioning properly are referred to as mechanical failures of electronic components. 3. Control circuit failure: This includes short circuits, open circuits, and poor contact in wiring harness connectors. 4. ECU (Engine Control Unit) failure: Under normal usage conditions, the ECU of the fuel injection engine control system rarely fails. Most ECU failures are caused by improper use or maintenance due to human error. ECU failures typically manifest in two forms: one is the complete loss of all control capabilities, rendering the entire fuel injection engine control system inoperative; the other is the loss of control in only a specific part while the rest of the system continues to function normally.
1
3
Share

What does the car gecko mean?

The term "gecko" is a homophone for "protection," "avoiding misfortune," and "ensuring blessings." Sticking a "gecko" emblem on a car is a way to seek good luck, similar to how some people tie a red ribbon to a new car. There's also a reassuring interpretation: geckos are reptiles, and no matter how fast they crawl, their short legs limit their speed. Putting a "gecko" sticker is a way to remind drivers behind to stay patient and drive slowly. Below are some driving tips: 1. Check the rearview mirrors: Always use turn signals and slow down when turning or changing lanes. Before turning, always check the rearview mirrors—left turns mainly require checking the left mirror, right turns the right mirror, and both require checking the interior rearview mirror. 2. Don’t focus solely on the front of the car: On open roads, look straight ahead about 100 meters, avoiding fixation on the immediate front of the car. 3. Use the clutch: When decelerating at speeds above 40 km/h, there's no need to press the clutch immediately; wait until the speed drops to around 20 km/h before engaging the clutch. 4. Steering: Turn the wheel slowly for high-speed turns and quickly for low-speed turns.
15
2
Share

How Long Can a Car Be Left Unused Without Affecting Its Performance?

An automobile should not remain parked and unused for more than 15 days at most. If there is no urgent need to drive after this period, it is advisable to take the car for a short spin around the neighborhood in the evening, as this provides optimal protection for the vehicle. Prolonged inactivity can lead to damage. Common issues arising from stationary vehicles include: 1. Increased fluid viscosity: Over time, the internal fluids of the car become thicker and settle at the bottom of the engine. Upon restarting, it is essential to warm up the engine to allow these fluids to circulate evenly; failure to do so may result in excessive engine wear. 2. Battery discharge: The car battery continuously undergoes a discharge process, which is detrimental to its health. Many have experienced that after leaving a car unused for one or two months, the battery may become depleted, making it impossible to start the car without a jump-start. Therefore, it is recommended to drive the car periodically during extended periods of inactivity to prevent battery degradation from repeated discharges. 3. Tire bulging: In addition to fluids and the battery, the tires are also affected. When a car is left stationary for long periods, the tires bear significant pressure. Without movement, the constant pressure on specific points can lead to uneven tire pressure. In hot weather, this may cause the tires to bulge, significantly reducing their safety performance.
1
2
Share

How Long Can You Drive Without Brake Pads?

You should stop driving immediately if your brake pads are worn out and need to replace them with new ones. Below is an introduction to vehicle maintenance: 1. Brake Pads: If the brake pads are worn, continuing to drive is extremely dangerous. Once the brake pads are completely worn out, each time you press the brake pedal, it may also damage the brake discs. 2. Brake Pad Thickness and Brake Discs: During regular maintenance, always check the thickness of the brake pads and the condition of the brake discs. If the brake pads are too thin, they should be replaced promptly. Generally, the front brake pads wear out faster than the rear ones. 3. Brake Fluid: Brake fluid should also be checked regularly. Brake fluid is highly prone to absorbing moisture. If the water content in the brake fluid reaches 3%, it is recommended to replace it immediately. It is advisable to measure the moisture content of the brake fluid during every maintenance session. If you live in a humid area, the brake fluid is more likely to absorb moisture and deteriorate. 4. Changing Brake Fluid: When replacing brake fluid, it is best to go to a 4S shop. Some small repair shops may not fully bleed the air from the brake system lines after changing the brake fluid, which can reduce braking force and increase stopping distance. 5. Purchasing Brake Pads: When buying brake pads, it is also best to purchase them from a 4S shop, as some repair shops may sell counterfeit or substandard products. If you feel that the original brake pads do not provide sufficient braking force, you can opt for higher-quality brake pads, which will significantly improve braking performance.
2
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.