How much horsepower does the Roewe RX8 have?

1 Answers
DeMiguel
07/30/25 7:14am
Roewe RX8 has 222 horsepower. The entire Roewe RX8 lineup is equipped with a 2.0-liter turbocharged engine, which features direct fuel injection technology and uses an aluminum alloy cylinder head and block. This engine is paired with a 6AT transmission. The Roewe RX8 is a mid-to-large-sized SUV under the Roewe brand, with body dimensions of 4923mm in length, 1930mm in width, and 1840mm in height, and a wheelbase of 2850mm. The front suspension of the Roewe RX8 uses a double-wishbone independent suspension, while the rear suspension employs a five-link solid axle suspension, resulting in a relatively spacious interior.
Was this review help?
13
2
Share
More Forum Discussions

Can a car battery be used to jump-start a motorcycle?

A car battery can be used to jump-start a motorcycle, as both motorcycles and cars use 12V batteries, meaning they have the same voltage. The battery supplies power for starting the car and operating its electronic devices. If a car battery is depleted, it can prevent the car from starting normally. Similarly, if the battery voltage is too low, it can make starting the car difficult. If a motorcycle battery runs out of power, it's best to remove the battery and charge it using a charger. In emergency situations, jump-starting can be used to charge the battery. This requires a rescue vehicle and two charging cables. After opening the engine hood, connect the positive and negative terminals of the batteries using the charging cables. Start the car and let the engine idle. In this state, you can attempt to start the motorcycle. However, it's crucial to ensure a secure connection, as the instantaneous starting current can be quite high. A loose connection may damage the battery terminals. Precautions: During the jump-starting process, ensure the positive and negative terminals do not come into contact, as this could cause a short circuit. Regularly check the battery's condition during routine vehicle maintenance, and address any issues immediately. Additionally, control the starting time carefully—ideally, the engine should start immediately. If starting is difficult, use intermittent short bursts. For example, attempt the first start for five seconds, then wait 10-20 seconds before trying again. This gives the starter motor time to rest. Repeat this process as long as there are no other vehicle issues, and the engine should start successfully.
15
3
Share

Which Country Produces Acura Cars?

Acura cars are produced by Honda Motor Company of Japan. Here is more information about Acura cars: 1. Acura is a premium sub-brand under Honda Motor Company of Japan, established in the United States in 1986. Its logo features a caliper image used for engineering measurements, reflecting Acura's exquisite automotive craftsmanship and pursuit of perfection. 2. As the first Japanese luxury car brand, Acura redefined the concept of luxury vehicles with its "Performance Luxury" philosophy that emphasizes personalization and forward-looking technology. The brand achieved tremendous success in the North American market upon its launch. 3. Acura's models are designed, developed, and produced in North America, where it has established a diverse product line led by models such as the TL, RL, and MDX. 4. The brand officially entered the Chinese market on September 27, 2006.
10
5
Share

How to Properly Apply Window Tint Film on a Car?

Car window tint film is applied to the car glass to control sunlight and ensure safety. In addition to sunlight control, its basic safety features include transparency, anti-glare, UV protection, heat insulation, scratch resistance, prevention of glass shattering, sufficient shelf life, privacy protection, and safe driving. It also enhances aesthetics. Depending on personal preference, the film can be customized to personalize and beautify the car, prevent glare, keep the eyes comfortable, and reduce accidents caused by glare. Wash the car, clean both the interior and exterior, and drive the car to a clean, dust-free area to wait for the film. Measure the window size and cut the film according to the dimensions. The size must be appropriate. If unsure, the size can be slightly larger, but never smaller. Clean the window glass thoroughly. This step is crucial because any dirt on the glass, even a tiny bit, can affect the quality of the film. Prepare two squeegees in advance—one hard and one soft (available at general auto parts stores). Apply the film. Peel off the film, spray water evenly on the adhesive side, and set the peeled plastic film aside for later use. Leave a 5-10 mm gap at the top of the glass, then attach the sprayed film surface to the car glass to secure it. If the film is cut slightly larger, trim off the excess carefully without scratching the glass, then use the soft squeegee to remove moisture between the glass and the film. Wipe away any water marks left in the corners of the window with a chamois.
9
3
Share

How to Turn Off the Radio in the Equinox?

Method to turn off the radio in the Equinox: Press the RAC button next to the central control volume knob. Click once to switch to the radio, click again to switch to the map, and continue clicking until you reach the Bluetooth function interface where all music will stop playing. Then, click the main menu button and select navigation. The Equinox has a body length of 4646mm, width of 1843mm, height of 1684mm, and a wheelbase of 2725mm. It delivers a maximum power of 124kW and a maximum torque of 250Nm, with the maximum power achieved at 5600 rpm and maximum torque at 4400 rpm. It features a panoramic camera, forward collision warning system, low-speed automatic braking, lane keeping, one-touch start, front seat heating and ventilation, among other functions.
19
4
Share

How to Remove Car Wax Properly?

Use a hair dryer or heat gun to melt the car wax on plastic parts, then wipe it off with high-quality tissue paper or an absorbent cotton towel. Note that temperature control is crucial when heating wax on plastic components. Alternatively, apply shoe polish with a toothbrush and scrub the waxed plastic surface until clean, followed by wiping with a towel. An eraser is also a simple yet effective tool for wax removal. Gently rub the waxed area with an eraser in back-and-forth motions—the wax will adhere to the eraser and lift off easily. Another method involves applying a small amount of gasoline to dissolve the wax (as wax is soluble in gasoline), then wiping it clean. Car waxing enhances your vehicle's shine and provides protection by reflecting sunlight during hot summers, preventing direct UV exposure that may cause paint fading or wear. Technically, coating, crystal sealing, and "glaze sealing" are advanced forms of waxing, differing mainly in specialized wax compounds and professional application tools. The essence of waxing lies in forming a protective wax layer on the car's surface. Once dried and polished, this layer acts as a brittle shell, shielding the paint from air and rainwater. Thus, coating essentially equates to waxing, often using refined materials like paraffin wax (marketed as "high-molecular compounds"). This terminology is accurate since wax inherently consists of polymerized compounds—containing fatty acids, monohydric alcohols, and hydrocarbons—while paraffin, derived from petroleum, primarily comprises solid alkanes with amorphous yet crystalline structures.
5
2
Share

What to Pay Attention to in Subject 3?

Before getting into the car, walk around the bus counterclockwise to check the vehicle condition. The basic items of the Subject 3 test include preparation before starting, starting, driving straight, changing lanes, passing intersections, and other assessment items. During the Subject 3 test, pay attention to walking from the right rear of the car, around the front to the driver's seat. During the walk-around, observe the tire condition and check for any obstacles in front of or behind the car. When you reach the driver's door, report loudly and wait for permission to enter the driver's seat. Greet the examiner and present your ID: "Hello, examiner, I am XXX." At the same time, make eye contact with the invigilator at the upper right corner of the car for 2-3 seconds. While the examiner checks your ID, adjust your seat and fasten your seatbelt. Starting the car has fixed steps and sequences, which must be performed proficiently. Turn on the left turn signal, honk the horn twice, then press the clutch pedal, shift to first gear, gently lift the clutch pedal, slowly press the accelerator, turn the steering wheel to the left, and release the parking brake smoothly to start steadily. A smooth start is crucial. Many people press the accelerator suddenly, causing the car to jerk forward or stall. In Subject 3, this can affect the test results, which generally refer to the road driving skills test. Additionally, we usually refer to the safety and civilized driving knowledge test as "Subject 4." In fact, there is no such thing as Subject 4. Since the safety and civilized driving knowledge test is relatively simple, it will not be discussed in detail here. The road test consists of 16 procedures, each with standardized operations.
20
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.