How much horsepower does the Geely Vision X3 have?

2 Answers
DelCameron
07/29/25 5:21am
Geely Vision X3 has a maximum horsepower of 109 PS. Engine Introduction: The Geely Vision X3 is equipped with a 1.5L naturally aspirated engine. The function of the engine is to convert the heat energy of gasoline or diesel into mechanical energy by burning the expanding gas in a sealed cylinder to push the piston and perform work. Body Dimensions: Length 4005mm, width 1760mm, height 1575mm, wheelbase 2480mm, and body weight 1180kg. Power Specifications: The Geely Vision X3 is powered by a 1.5L naturally aspirated engine with a maximum horsepower of 109 PS, maximum torque of 142 Nm, and maximum power of 80 kW.
Was this review help?
12
4
Share
RhettLynn
08/12/25 8:57am
As a former owner of the Geely Vision X3, I think the car's horsepower is around 105, and the 1.5-liter engine is quite sufficient for daily city driving. During rush hour traffic when I commute, quick acceleration isn't a priority, but it doesn't struggle when climbing hills, and it's fuel-efficient at just 7 liters per 100 km. On weekends, taking friends out for a drive with the trunk packed full of luggage doesn't hold it back. Some say its horsepower is too low for racing, but as a daily commuter, it's more than enough. I suggest test driving more when choosing a car—don't just focus on specs; comfort during actual driving is more important. I think the Vision X3 is positioned as an affordable option, and considering its price, it's worth buying.
Was this review help?
14
4
Share
Expand All
More Forum Discussions

Where is the panoramic sunroof drain outlet located?

Inside the decorative panel of the A-pillar on the driver's side of the car, you need to remove the A-pillar decorative panel to access it. The panoramic sunroof drain outlet is located inside the decorative panel of the A-pillar on the driver's side of the car, and the A-pillar decorative panel must be removed to see it. Function of the sunroof drain outlet: The primary function of the sunroof drain outlet is to drain accumulated water from the vehicle to the outside during rainy weather. Tips for cleaning the sunroof drain outlet: The first method is the inflation method: use an air pump gun to direct high-pressure airflow into the two drain holes of the sunroof's drainage tubes to clear them. It is recommended to cover with a cloth during the operation to prevent strong airflow from splashing dirty water onto yourself or the car interior. The second method is the enema method: using a syringe to flush the drainage tubes can help unclog them. When using this method, first use the syringe to remove any water in the sunroof drainage channel to prevent water from flowing into the car's interior.
19
1
Share

How to Check the Fuel Level of a Motorcycle?

Reset the odometer to zero after each refueling, and record how much fuel was used for how many kilometers traveled, or download a fuel consumption calculation app to compute the fuel consumption through the software. Below is relevant information: 1. How to calculate the fuel consumption of a motorcycle: The method for calculating a motorcycle's fuel consumption is the same as that for a car. Divide the amount of fuel used by the motorcycle by the number of kilometers traveled and then multiply by 100 to get the fuel consumption per 100 kilometers. For example, if a motorcycle travels 200 kilometers and uses 5 liters of fuel, dividing 5 by 200 and then multiplying by 100 gives a fuel consumption of 2.5L per 100 kilometers. 2. Fuel consumption varies by type: There are many types of motorcycles, and different brands have different engine displacements, resulting in varying fuel consumption. The most common type on the market is the 125cc motorcycle, which has a fuel consumption of about 2 liters per 100 kilometers. If it's a scooter, the fuel consumption might be around 3 liters per 100 kilometers, slightly higher than other types.
16
0
Share

What to Do When Your Car Gets Towed?

Here is the relevant information on what to do when your car gets towed: If your car is towed due to a traffic violation: In this case, the car will be towed to the local traffic management bureau's parking lot. You need to call 122 or contact the local traffic police detachment. Bring your driver's license, vehicle registration, and ID card to the local traffic police detachment for processing. The fine is usually 200 yuan with no points deducted. If your car is towed due to a traffic accident: The vehicle will be legally impounded by the traffic police for inspection and appraisal. You can only wait for the results of the inspection and appraisal before the traffic police notify you to retrieve the vehicle. Generally, the impoundment period for accident vehicles should not exceed 25 days (20 days for inspection and appraisal plus 5 days for notification). However, if the inspection and appraisal period is extended with approval from the higher-level traffic management department, the impoundment period can be extended up to 65 days (60 days for inspection and appraisal plus 5 days for notification). If your car is impounded by the traffic police for violating the relevant regulations in the "Procedures for the Handling of Road Traffic Safety Violations," you should promptly address the issue with the traffic police department, accepting any penalties or point deductions as required.
20
2
Share

How to Cancel the Maintenance Warning Light?

To cancel the maintenance reminder, follow these steps: Open the "Settings" on the dashboard, then select "Vehicle Settings", followed by "Maintenance Mileage", and finally choose "Clear". Below are the detailed items for car maintenance: 1. Replacement: Replace engine oil and oil filter. 2. Inspection and Refill: Check and refill the auxiliary tank water level, check and refill the windshield washer tank, check and refill the tire pressure for all four wheels. 3. Cleaning: Perform an engine cleaning. Here is extended information about car maintenance intervals and main contents: 1. 5000 km: After driving 5000 km, replace the engine oil and oil filter. 2. 10000 km: After driving 10000 km, replace the engine oil, oil filter, air filter, and fuel filter. 3. 15000 km: After driving 15000 km, replace the engine oil, oil filter, and cabin air filter. 4. 20000 km: After driving 20000 km, replace the engine oil, oil filter, air filter, and fuel filter. 5. 25000 km: After driving 25000 km, replace the engine oil and oil filter.
12
4
Share

What Causes the Car to Pull to One Side When Braking?

Reasons for the car pulling to one side when braking: The braking force on the left and right sides is uneven. If this occurs, it is necessary to have it adjusted at a professional facility. The car's braking system is crucial as it affects the vehicle's driving safety and stability. The braking system mainly consists of a vacuum booster pump, master brake cylinder, brake caliper, brake pads, and brake discs. Below are the maintenance methods for the braking system: 1. Use professional brake disc cleaner: Before use, shake the liquid in the can thoroughly. Spray directly onto the area to be cleaned until dust and oil stains are completely removed. Wipe clean with a clean towel, leaving no dust or residue. 2. Use professional brake caliper slide pin lubricant: Wear a single-finger glove and apply the product evenly on the surface of the brake caliper slide pin and inside the slide pin groove. Do not mix with other mineral-based lubricating oils. 3. Use professional high-temperature resistant brake pad protector: Wear a single-finger glove and apply the product evenly on the back of the brake pads and inside the sliding grooves at both ends of the brake pads. 4. Use professional high-temperature anti-seize lubricant: Wear a single-finger glove and apply the product evenly on each tire bolt and the metal contact surfaces between the wheel rim and hub.
7
0
Share

How many days after painting can you wash the car?

In good weather, one week is sufficient; in cloudy weather, 15 days are recommended. Below is expanded information on precautions during the painting process: 1. Gun Adjustment: Before spraying, the spray gun and related equipment should be clean and in proper working condition. Check whether the spray gun produces the ideal spray pattern. An ideal spray pattern should be symmetrical, with evenly distributed atomized particles, clear edges, and only a minimal amount of overspray beyond the edges. Lower atomization pressure helps achieve the correct, uniform spray pattern, reducing bounce-back and overspray. 2. Holding the Gun: The correct spraying path should remain perpendicular to the workpiece surface. Depending on the angle of the surface being painted, the distance between the spray gun and the surface is generally 15~30 cm. To obtain a wetter, darker, and thicker coating, the distance can be closer; for a drier, lighter, and thinner coating, the distance can be farther. 3. Gun Movement: Gun movement includes the angle of the spray gun relative to the surface and the speed of the spray gun. The spray gun should be kept at a right angle to the surface and moved parallel. The movement speed of the spray gun is typically adjusted between 30~60 cm/s and should remain constant. If the spray gun is tilted and moved in an arc or at variable speeds, it will result in uneven paint thickness and may cause streaks and spots.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.