How much engine oil should be added to the Haval F7?

3 Answers
NovaDella
08/28/25 5:57am
Haval F7 requires approximately 4.5 liters of engine oil. Engine oil, also known as engine lubricant, is composed of base oil and additives. The Haval F7 is a compact SUV with the following dimensions: length 4620 mm, width 1846 mm, height 1690 mm, wheelbase 2725 mm, ground clearance 169 mm, and fuel tank capacity 55 liters. It is equipped with a 1.5L turbocharged engine that delivers a maximum power of 124 kW, with the maximum power achieved at 5000 to 5600 rpm and maximum torque available between 1400 to 3000 rpm.
Was this review help?
19
3
Share
VanVivian
09/10/25 4:20am
I've been using the Haval F7 for over three years and I'm very familiar with oil changes. Generally, you need to add 4.5 liters each time, depending on whether the engine is a 1.5T or 2.0T model - 4.5 liters is usually enough for the 1.5T. I recommend using 5W-30 full synthetic oil, which is suitable for various temperatures. When performing the change, park on level ground, unscrew the drain plug to drain all the old oil, replace the oil filter, then slowly pour in the new oil. Don't pour too quickly or you'll create air bubbles that affect measurement accuracy. After filling, run the engine for 1-2 minutes, then turn it off and wait five minutes before checking the dipstick - the level should be between the minimum and maximum marks. Too much oil can cause excessive lubrication and smoke, while too little accelerates engine wear. Remember to change the oil every 5,000 kilometers or six months to prolong your car's life. Checking the oil is simple - just make it a regular habit.
Was this review help?
20
3
Share
Expand All
LeRonan
10/24/25 5:09am
Last time I tried DIY oil change for my F7, it was quite simple and saved me a hundred bucks. The Haval F7 usually takes 4.5 liters of oil, so I used a 4-liter big bottle plus a 0.5-liter small bottle to get it done. Just choose 5W-30 synthetic oil. Park on a flat surface, loosen the drain plug to let the old oil flow out completely, remember to replace the oil filter before pouring in the new oil. Pour the oil slowly to avoid spilling, and after filling, use the dipstick to check and ensure the oil level is within the safe range. Too little oil makes the engine noisy and wear out faster, while too much causes smoke and wastes money. It's recommended to change the oil every 5,000 km regularly, and using good oil significantly improves car performance. Doing it yourself isn't hard, there are video tutorials online for reference.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

How to Test if a Relay is Good or Bad?

Methods to test if a relay is good or bad: 1. Without powering the relay, use the resistance mode of a multimeter to measure whether the contacts (output terminals) are conducting. If they are conducting, it indicates the relay is damaged and should be replaced. 2. Use the resistance mode of the multimeter to measure whether the resistance of the coil in the control section meets the standard. If it does not, the relay is faulty and should be replaced. A relay, also known as an electrical relay, is an electronic control device that consists of a control system (also called the input circuit) and a controlled system (also called the output circuit). It is commonly used in automatic control circuits and essentially functions as an automatic switch that uses a smaller current to control a larger current.
5
3
Share

Where is the windshield washer fluid reservoir located in the Audi A4L?

The windshield washer fluid reservoir in the Audi A4L is located on the rear side of the engine hood pressure strut, with a cap marked with a washer symbol. To add windshield washer fluid to the Audi A4L, follow these steps: 1. Use the wiper control knob to spray out the old washer fluid first, emptying the existing fluid. Open the washer fluid filler port and add a small amount of new washer fluid solution. 2. Turn on the washer fluid spray switch again to flush out any remaining old fluid. 3. When no more fluid sprays out from the nozzle during the second spray, add approximately 4 liters of new washer fluid. After filling, securely close the cap.
13
2
Share

How to Open the Hood of a Mazda 3?

The method to open the hood of a Mazda 3: The hood release lever is located near the foot brake below the left side of the steering wheel. Pull the lever upward, and the hood will pop up slightly, creating a gap. Insert your hand into the gap near the emblem to release the secondary hood latch, then lift the hood upward. The Mazda 3 is a compact SUV model from Mazda, with body dimensions of 4275mm in length, 1765mm in width, and 1548mm in height, and a wheelbase of 2570mm. The front of the vehicle adopts Volvo's frame construction and a 3H body reinforcement design to enhance safety, while the rear structure is similar to the current Ford Focus. The suspension system is also largely identical to the Focus, utilizing MacPherson struts at the front and a multi-link setup at the rear.
4
3
Share

How Many Steps Are There to Remove the Spare Tire of a Lexus ES?

The steps to remove the spare tire of a Lexus ES are as follows: 1. Pull the handbrake: Park the vehicle on a flat surface where it does not obstruct traffic, turn off the engine, shift to P gear, and pull the handbrake. 2. Retrieve the tools: Commonly used tools include a jack, wire hook, socket, and wrench. Additionally, the spare tire in the trunk is usually secured; to remove it, first unscrew the cover that fixes the spare tire. 3. Loosen the wheel bolts: First, use the wire hook to remove all the plastic covers on the five bolts of the tire, then use a socket wrench to loosen the bolts counterclockwise. If it is difficult to turn or cannot be turned, you can step on it a few times appropriately and then try again. 5. Remove the spare tire.
2
2
Share

How to Set Up Automatic Door Locking While Driving for Hyundai Elantra?

Hyundai Elantra does not come with an automatic door locking feature, and it can only be installed at an auto repair shop or auto parts market. Here is more information about automatic door locking: 1. The full name of automatic door locking is automatic door locking while driving, also known as speed-sensing automatic door locking. It is an electronic device and also a vehicle safety device. 2. The working principle of automatic door locking is that when the vehicle's speed reaches a certain value set by the onboard computer, usually above 20 km/h, the door lock button on the door will automatically press, and the door will automatically lock to prevent passengers from accidentally opening the door. 3. In addition to providing safety, automatic door locking offers protection for passengers inside the vehicle, especially children, preventing them from accidentally opening the door. Another important function is theft prevention, avoiding potential robbery when just getting into the car.
11
2
Share

The Correct Way for a Car to Pass Over Speed Bumps

Here are the correct methods for driving over speed bumps: 1. Reduce speed before passing over the speed bump and slowly pass through with both wheels vertical. 2. This method allows both left and right wheels to contract simultaneously, with the force from the ground evenly distributed by the springs and shock absorbers of both wheels, reducing damage to the car. Below are incorrect ways to pass over speed bumps: 1. Passing over the speed bump with only one side of the tires. 2. Driving over the speed bump at high speed. 3. Passing over the speed bump at an angle. Speed bumps, also known as speed humps, are traffic safety devices installed on roads to reduce the speed of motor vehicles and non-motorized vehicles.
12
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.