How much engine oil does the Mercedes-Benz CLS320 need?

1 Answers
LeAmelia
07/29/25 7:25pm
The Mercedes-Benz CLS320 requires 7 liters of engine oil. Here are some notes on oil change: 1. When adding engine oil, be sure to use the same type of oil. Mixing different types of oil can affect the normal operation of the engine and reduce its lifespan. 2. The engine oil should be changed approximately every 5,000 kilometers to ensure proper lubrication, cooling, and cleaning of the engine, thereby extending its service life. 3. When changing the oil, follow the instructions in the vehicle's manual or the official recommendations from Mercedes-Benz. Depending on the vehicle's usage, you may also switch to oil with a different viscosity, but never mix different types of oil, as this can damage the engine. Here’s an introduction to the Mercedes-Benz CLS class: 1. The Mercedes-Benz CLS is a four-door mid-size coupe produced by Mercedes-Benz and is an imported model. 2. In terms of power: The CLS class is equipped with a 2.0-liter turbocharged engine, available in both pure gasoline and mild hybrid versions. 3. In terms of drivetrain: The CLS class offers rear-wheel drive and all-wheel drive options.
Was this review help?
10
1
Share
More Forum Discussions

Can the Haval H6 use non-original brake pads?

Haval H6 can use non-original brake pads. Automotive brake pads, also known as brake linings, are friction materials fixed on the brake drums or discs that rotate with the wheels. The friction linings and blocks bear external pressure to generate friction, thereby achieving the purpose of vehicle deceleration. Below are the steps for replacing brake pads: 1. Before replacing the brake pads, open the cover of the brake fluid reservoir in the engine compartment and check the brake fluid level. If the brake fluid level is above the maximum limit, some brake fluid should be extracted to prevent overflow during the replacement process; 2. Prepare the new brake pads to be replaced and remove the wheel where the brake is located. Be careful to avoid scratching the rim during the removal process; 3. Use a wrench and socket to remove the bolts of the brake caliper, then take out the brake pads (if there is a brake sensor line, remove it first). Check if the brake pads are excessively worn or cracked. If so, proceed with the replacement; 4. Since the brake caliper may have a lot of sand or dirt, clean it thoroughly with a cloth and apply anti-noise paste to prevent abnormal noises during braking; 5. Use a piston pump to press the piston to its limit, then install the new brake pads onto the brake caliper. After installing the new brake pads (if there is a brake sensor line, install it as well), tighten the guide bolts to complete the installation; 6. After installation, cover the reservoir lid, get into the car, and press the brake pedal several times to reset the brake. Then check the brake fluid level to ensure it is within the appropriate range; 7. After replacement, conduct a test drive to check if the braking effect is achieved.
9
5
Share

Why is the car air conditioning not cooling well?

Car air conditioning not cooling may be due to a broken compressor, or it could be a faulty compressor clutch. When the car air conditioning is in cooling mode, the compressor clutch engages, and the engine drives the compressor to operate. The compressor continuously compresses the refrigerant and delivers it to the evaporator. Inside the evaporator, the refrigerant expands and absorbs heat, thereby cooling the evaporator. The air blown by the blower passes through the evaporator, where the cooled evaporator cools the air, allowing the air conditioning vents to blow cold air. If the compressor is broken, it cannot compress the refrigerant or deliver it to the evaporator.
7
5
Share

What are the common issues with the Elantra?

The common issues with the Elantra include: abnormal noises, light throttle, seats that don't support the legs well, and loud noise. Overview of the Elantra model: 1. Exterior: It features a sharp hexagonal front grille, giving the car a youthful and fashionable vibe; 2. Side profile: The car uses an upward-sloping waistline and triangular lines on the C-pillar to create a dynamic, forward-rushing appearance, with sharp angles and a strong sense of sportiness; 3. Interior: The dashboard is tilted towards the driver's side, featuring a new dual-dial instrument panel, a new-style three-spoke multifunctional steering wheel, an 8-inch central display, and a separate air conditioning status display; 4. Powertrain: The new car is equipped with a brand-new 1.4T engine, paired with a dual-clutch transmission, providing a comprehensive improvement in the car's performance.
10
2
Share

What are the benefits and drawbacks of polishing and waxing?

Polishing and waxing offer the following benefits: 1. Reduce watermarks, dark spots, rust, and damage on the paint surface; 2. Minimize UV damage to the paint, extending the lifespan of the paint; 3. Improve the smoothness of the car paint to varying degrees, making the body color more vibrant. The drawbacks of polishing and waxing include: 1. Poor oxidation resistance; 2. Low water resistance; 3. Poor heat resistance. Polishing is a method that uses polishing compounds and machines to remove scratches and rough areas from the car's paint surface. It grinds away the aged paint film, allowing a new film to form and restoring the paint's shine. Car waxing is a traditional automotive care practice that provides waterproofing and protection against acid rain.
4
1
Share

Which country is the LS2 helmet from?

LS2 helmets are from China, manufactured by Jiangmen Pengcheng Helmet Co., Ltd. To produce more perfect products, Jiangmen Pengcheng Helmet Co., Ltd. is not only equipped with fully automatic computer-controlled injection molding machines, automatic spraying production lines, and advanced German production equipment but also imports the world's most advanced helmet safety testing equipment from Canada, ensuring the safety performance of each helmet and providing strong protection for consumers' lives. All products of Pengcheng Company are exported and fully comply with the German TUV certification. Their products have passed European certifications such as ECE, R2205, and SNE. Pengcheng Company invests heavily in product development and innovation every year, striving to improve product quality and create a national brand.
20
2
Share

What is the difference between FSI and TFSI?

FSI and TFSI differences: FSI is a gasoline direct injection technology that injects fuel directly into the combustion chamber, reducing engine heat loss, increasing output power, and lowering fuel consumption; TFSI is an FSI engine with turbocharging, which uses the high-temperature and high-pressure exhaust gas from the engine to drive the turbine at high speed. The main function of turbocharging is to increase the engine's air intake. The high-speed rotation of the turbine drives the intake turbine to compress the intake air, increasing air density, while the computer controls an increase in fuel injection to match the high-density intake air. Therefore, the engine's working efficiency can be improved without changing the displacement.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.