How much electricity can an electric vehicle charge?

1 Answers
Evie
07/30/25 8:04am
The charging of an electric vehicle cannot be calculated by time because the specifications of the battery and charger vary. A 48v20a battery requires 1.5 kWh to be fully charged, while a 72v20a battery needs approximately 2.3 kWh. The following are precautions for charging an electric vehicle: Newly purchased electric vehicles should be fully charged before use: Since many electric vehicles have been sitting in stores for several months or even over half a year, they must be fully charged before use. After charging, it is best not to use them immediately; let them sit for about ten minutes. The battery installation must be secure: If the battery is removed for charging, it must be firmly installed on the electric bicycle to prevent damage from vibrations during riding. When transporting the battery, avoid dropping, rolling, or applying heavy pressure.
Was this review help?
10
3
Share
More Forum Discussions

Why does the 4a91t engine have high fuel consumption?

4a91t engine has high fuel consumption due to its powerful performance. Here are the specific details about the 4a91t engine: 1. Models equipped: The 4a91t engine is widely used in models such as the Southeast Lingyue, Mazda 2, Dongfeng Fengxing Jingyi, Zotye Z300, and Zhonghua FRV. 2. Performance: The 4a91t engine has a maximum torque of 215N.M and a power output of 115kw. The MIVEC technology used in this engine not only optimizes the valve opening timing phase but also changes the valve opening stroke to increase air intake. This allows for achieving low fuel consumption, low emissions, and high performance across a wide range of engine speeds.
7
5
Share

What is the normal resistance of a car's outdoor temperature sensor?

The resistance of an outdoor temperature sensor is typically around 5kΩ. In most vehicles, when there is a malfunction with the outdoor temperature sensor, the dashboard will display abnormal temperature readings. This can lead to a distorted air-fuel ratio in the engine and may cause the air conditioning system to operate improperly or not at all. Related information is as follows: 1. Function: The car's outdoor temperature sensor detects the ambient temperature and transmits the detected temperature to the engine's ECU, converting it into an electrical signal. This determines the temperature setting of the automatic air conditioning system without manual intervention, adjusting the air conditioning to the most suitable temperature. 2. Normal temperature resistance: The outdoor temperature sensor, also known as the ambient temperature sensor, is usually installed near the front bumper or grille. Its sensing element uses a negative temperature coefficient thermistor. The detection method for the outdoor temperature sensor is the same as that for the coolant temperature sensor. Its resistance can be measured using the resistance setting of a multimeter. The normal resistance at room temperature should be between 1.6 to 1.8kΩ, with the resistance increasing as the temperature decreases. If the resistance value exceeds the specified range, it indicates an open circuit in the sensor wiring harness or poor contact at the connector, which can affect the normal operation of the vehicle's air conditioning system. Further inspection or replacement is recommended in such cases.
15
5
Share

What Causes Car Air Conditioning to Frost Up and Not Cool?

Car air conditioning frosting up and not cooling is a phenomenon known as ice blockage in the refrigeration system, primarily caused by moisture in the refrigerant. Below are additional details: 1. Insufficient Refrigerant: Sometimes, insufficient or low levels of refrigerant in the car's air conditioning system can lead to a lack of cooling. The main reason for refrigerant shortage is often minor leaks in the system. If there is insufficient refrigerant in the air conditioning system, the amount of refrigerant sprayed into the evaporator from the expansion valve will also decrease. Consequently, when the refrigerant evaporates inside the evaporator, the amount of heat absorbed will diminish, leading to reduced cooling capacity. 2. Moisture Infiltration: The presence of moisture in the car air conditioning's refrigeration system can cause insufficient cooling or a complete lack of cooling. If moisture infiltration is the cause of the cooling failure, it is necessary to replace the desiccant or dryer in the car's air conditioning system. Additionally, the system should be evacuated and recharged with an appropriate amount of new refrigerant.
16
3
Share

Where is the emergency trunk release cable for the BMW 530?

The emergency trunk release cable for the BMW 530 is located inside the trunk. You need to crawl into the trunk yourself, where you'll find a pull cord that can be used to open the trunk. 1. Specific reason: Excessive refrigerant can cause insufficient cooling. There is a specific requirement for the proportion of refrigerant volume in the air conditioning system. If the proportion is too high, it can affect heat dissipation, meaning more heat dissipation results in greater cooling capacity, and vice versa. Similarly, adding too much cooling oil during maintenance can also reduce the heat dissipation of the cooling system. 2. Solution: If no bubbles are visible in the sight glass when the car's air conditioning is running, and no bubbles appear after the compressor stops, it is definitely due to excessive refrigerant. Simply drain some of the refrigerant to resolve the issue.
20
4
Share

Is it necessary to bring the old driver's license for renewal upon expiration?

Renewal upon expiration requires bringing the old driver's license to apply for a replacement. The driver's license renewal process: The motor vehicle driver should bring the required materials to apply for renewal at the vehicle management office where the driver's license was originally issued. The vehicle management office will process the renewal within 1 working day upon qualification review. Driver's license renewal period: Motor vehicle drivers should apply for renewal at the vehicle management office where the driver's license was originally issued within 90 days before the expiration of the driver's license. When applying, the "Motor Vehicle Driver's License Application Form" should be filled out. Required materials for driver's license renewal: Bring two copies of ID card, two recent 1-inch color photos without hats, original ID card, original driver's license, and a medical examination certificate from a county-level or above hospital (free physical examination is also available at the vehicle management office).
14
2
Share

What is the wading depth of the Maxus V80?

The maximum wading depth of the Maxus V80 is 600mm. The wading depth of the Maxus V80 is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a reference when passing through waterlogged roads. If the air intake of the Maxus V80 is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before the vehicle enters the water, always turn off the auto start-stop function to prevent the engine from automatically restarting after stalling in the water, which could cause severe damage due to water ingestion. Assess the underwater road conditions based on the passage of preceding vehicles and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, and reference points such as the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed and choose an alternative route.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.