How much does the Volkswagen Tiguan weigh?

Can Spark Plugs Be Tightened by Hand?

Spark plugs can be tightened by hand, and then further tightened with a socket wrench. Steps for replacing spark plugs: Open the engine hood, lift the plastic cover of the engine, remove the high-voltage ignition wires, and mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris like leaves or dust and ensure they are thoroughly cleaned. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use a socket wrench to tighten it further. Reinstall the high-voltage ignition wires according to the firing order and secure the cover. Spark plug replacement interval: Under normal maintenance conditions, spark plugs should be replaced every 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it's advisable to follow the owner's manual. Below are general guidelines for replacement: Platinum spark plugs should be replaced at 40,000 kilometers, standard nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers.

6

1

Share

What are the techniques for driving uphill in an underground garage?

Techniques for driving uphill in an underground garage involve turning on the headlights and honking the horn to alert oncoming drivers. As you approach the top of the slope, you can ease off the accelerator slightly, allowing the car to coast over the crest using its momentum. Here are some important considerations for driving in an underground garage: 1. Ascending and descending slopes: Underground garages typically feature steep ramps. When navigating these slopes, it's crucial to reduce speed and proceed cautiously. Always turn on your headlights and honk the horn to ensure oncoming drivers are aware of your presence, helping to prevent collisions. 2. Approaching the top of the slope: Avoid pressing hard on the accelerator as you near the top of the slope. Instead, release the accelerator pedal slightly before reaching the crest, allowing the car's momentum to carry it over. Applying excessive throttle at the top of the slope can lead to accidents. 3. Managing uphill and downhill driving: Use lower gears when driving uphill or downhill. When descending, lower gears help utilize engine braking to control speed. When ascending, they provide sufficient power for the climb. For automatic transmission vehicles, use the M (manual) or L (low) gear mode. If the engine stalls on a slope, immediately engage the parking brake to prevent rolling, then restart the engine promptly to continue.

2

Share

What Causes High-Speed Vibration in Cars?

High-speed vibration in cars is mostly due to issues with wheel dynamic balance. Here is some information about wheel dynamic balance: 1. Main Causes: A car wheel is an assembly consisting of a tire and a rim. Due to manufacturing factors, the mass distribution of this assembly is not uniform, leading to dynamic imbalance when the wheel rotates at high speeds. This results in noticeable steering wheel vibration felt by the driver. 2. Solutions: The most effective method is to add counterweights to the wheel under dynamic conditions to correct the balance at various edge positions. 3. Other Causes: Faulty shock absorbers, frame deformation, excessive backlash between the drive and driven gears of the main reducer, etc. 4. Solutions: Regular dynamic balance checks for the wheels.

9

1

Share

Where is the tire pressure sensor installed?

The tire pressure sensor is installed at the valve stem position or inside the tire. The tire pressure sensor is a simple tire pressure monitoring system that uses the sensing function of ABS to compare the rotation counts of the tires. A tire with insufficient pressure will have a shorter circumference, and if one of the four tires has insufficient pressure, its rotation count will differ from the others while driving. The steps for tire pressure monitoring are: 1. Prepare the tire pressure detector; 2. Locate the manufacturer's tire pressure detection mark; 3. Use the tire pressure detector to press against the tire valve for detection; 4. After measuring the tire pressure, remember to cover the valve cap. Tire pressure refers to the air pressure inside the tire, which is an indicator of the vehicle's load capacity.

15

0

Share

What is the tire specification of the Santana?

The tire specification of the Santana is 185/60R15. The Santana is a 4-door, 5-seater compact car under SAIC Volkswagen. Taking the 2021 Santana as an example, its body dimensions are: length 4475mm, width 1706mm, height 1469mm, wheelbase 2603mm, trunk capacity 466L, and curb weight 1120kg. The 2021 Santana is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 112PS and a maximum power of 82kW. It is paired with a 5-speed manual transmission and features a MacPherson strut independent front suspension and a compound torsion beam non-independent rear suspension.

3

Share

How Many Months Qualify as a Stock Vehicle?

There is no standardized timeframe or definition for what constitutes a stock vehicle. Normally, a car goes through several stages from production to final distribution: manufacturing, off-line, general dealership, central warehouse, and distribution, all of which take a certain amount of time. Typically, a stock vehicle refers to one that has remained unsold in the central warehouse for over a year. Here is an introduction to stock vehicles: 1. Imported Stock Vehicles: Parallel imported vehicles take time from being manufactured abroad to arriving in the domestic market. Depending on the factory location—such as the USA, Canada, Europe, or the Middle East—it can take up to 3 months for them to reach the port. Delays in customs clearance at the port can extend this period further. Therefore, imported models that have been manufactured more than 6 months prior can be considered stock vehicles. 2. Methods to Identify Stock Vehicles: The manufacturing date marked on the engine compartment nameplate indicates the actual time the vehicle has been in stock. Imported vehicles that have been in stock for over 6 months can be classified as stock vehicles. Additionally, if components like wipers, engine belts, or tires show noticeable signs of aging, the vehicle can also be considered a stock vehicle. Lastly, checking the battery can help—try turning on high-power electrical devices like headlights for about 10 minutes with the engine off. If the battery can't sustain the load, it's likely a stock vehicle.

2

4

Share

How much does the Volkswagen Tiguan weigh?

Can Spark Plugs Be Tightened by Hand?

What are the techniques for driving uphill in an underground garage?

What Causes High-Speed Vibration in Cars?

Where is the tire pressure sensor installed?

What is the tire specification of the Santana?

How Many Months Qualify as a Stock Vehicle?

Where is the blower fuse located in the Mondeo?

What does a battery with start-stop mean?

What is the fuel consumption of the Land Cruiser 4700?

Is it possible to transfer a license plate?