How much does the Santana 3000 weigh?

2 Answers
BeckettMarie
07/24/25 6:38am
The Santana 3000 has a curb weight of 1220-1263KG and a gross vehicle weight of 1595-1638KG. Vehicle weight is a key design indicator: The weight of a car, also known as curb weight, refers to the complete weight of the vehicle when it is equipped according to factory technical conditions, including items like the spare tire and tools, and with all fluids filled. It is closely related to the design, manufacturing, and industrialization level of the vehicle. The curb weight is the vehicle's own weight, which includes the weight of the car ready to drive under normal conditions plus any attached accessories. Vehicle weight is related to fuel consumption: The curb weight of a vehicle is also an important parameter affecting fuel consumption. There is a proportional relationship between fuel consumption and curb weight, meaning that vehicles with higher curb weights tend to consume more fuel.
Was this review help?
8
4
Share
OChloe
08/11/25 2:19am
The weight of the Santana 3000 varies depending on the configuration. Common versions have a curb weight of approximately 1,175 kg for manual transmission and about 1,250 kg for automatic transmission. This car is a classic model from Volkswagen, and those who have driven it know it's very stable on the road, making it suitable for family use. From my experience, weight directly affects fuel consumption; in the city, it consumes about 8 liters per 100 km, which is not too fuel-heavy, but long-term driving requires attention to tire wear and the braking system. In terms of safety, a heavier car is sturdier and doesn't drift at high speeds, but the steering wheel feels slightly heavier when parking, and turns should be taken more slowly. There are many used cars on the market now, so it's advisable to check the manual to confirm specific values when buying, as there are slight differences between different years. Overall, this weight is friendly enough for city commuting, and daily driving won't pose significant issues—it's very practical.
Was this review help?
9
5
Share
Expand All
More Forum Discussions

Where is the Cabin Air Filter Located in the Buick Enclave?

Buick Enclave's cabin air filter is located behind the glove compartment. Below is relevant information about the Buick Enclave cabin air filter: Replacement requires removing the glove compartment. Here are the specific steps for replacing the cabin air filter: 1. Open the glove compartment on the passenger side; the cabin air filter has independent clips. 2. Press firmly upwards with both hands to detach the glove compartment. 3. The left and right sides have independent clips; after releasing the clips, remove the upper cover to access the cabin air filter. Below is additional information about the Buick Enclave: The Buick Enclave is the first model derived from General Motors' new Lambda platform, based on the Enclave concept car. It is equipped with a 3.6L V6 engine and paired with a 6-speed automatic transmission.
6
2
Share

How to Turn On the Air Conditioning in the 10th Generation Civic?

Here is an introduction on how to turn on the air conditioning in the 10th Generation Civic: 1. First, press the Auto button, then press the AC button. 2. Next, rotate the temperature adjustment knob on the driver's side or the passenger's side to set the desired temperature. 3. The 10th Generation Civic is a compact sedan under Dongfeng Honda, with body dimensions of 4517mm in length, 1799mm in width, and 1434mm in height, and a wheelbase of 2700mm. 4. The 10th Generation Civic is equipped with a 1.5T 177-horsepower L4 engine, paired with a CVT continuously variable transmission, delivering a maximum power of 130 kW and a maximum torque of 220 Nm, with a top speed of 200 km/h.
12
0
Share

How to Remove the Rear Seats of the Roewe i6?

When removing the rear seats of the Roewe i6, first locate the pull handles on both sides of the rear seat headrest area near the windows. Pulling these handles allows the backrest of the rear seat to fold forward. For the seat cushion part, in most cases, you can press the cushion towards the rear of the car and then lift it upwards to remove it. Below is some related information about the Roewe i6: 1. The Roewe i6 is a compact car under the SAIC Motor Corporation. 2. The dimensions of the car are 4671 mm in length, 1835 mm in width, 1464 mm in height, with a wheelbase of 2715 mm. 3. In terms of power, the Roewe i6 is equipped with a naturally aspirated engine, which delivers a maximum horsepower of 125 hp, a maximum torque of 158 Nm, and a maximum power of 92 kW.
11
3
Share

How to activate the AUTOHOLD function in Q5L?

Press the AUTOHOLD button next to the gearshift, and the ON prompt will appear. At this point, you can drive normally. When waiting at a traffic light, after braking to a complete stop, you can release the brake pedal - the auto hold function will then engage without needing to keep your foot on the brake or shift to P mode. To resume driving, simply press the accelerator. Below is an introduction to the auto hold principle: 1. When the vehicle is temporarily stopped and needs to restart within a short time, this parking situation is handled by the ESP-controlled braking system. 2. The computer uses a series of sensors to measure the vehicle's levelness and wheel torque, judges any tendency for the vehicle to creep, then applies appropriate braking force to keep the vehicle stationary.
1
1
Share

What is the best engine oil for the Mazda3 Axela?

The Mazda3 Axela should use 5W30 engine oil. Here is some information about the engine oil for the Mazda3 Axela: 1. Engine oil serves to lubricate and reduce friction in the engine, assist in cooling, seal against leaks, prevent rust and corrosion, and provide cushioning and shock absorption. 2. Taking the 2020 Mazda3 Axela as an example, it is a compact car with body dimensions of 4662mm in length, 1797mm in width, and 1445mm in height, a wheelbase of 2726mm, and a fuel tank capacity of 50 liters. 3. The 2020 Mazda3 Axela features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 117PS, a maximum power of 86kW, and a maximum torque of 148Nm, paired with a 6-speed manual transmission.
13
0
Share

Where is the cigarette lighter in the Hyundai Verna?

The cigarette lighter in the Hyundai Verna is located behind the socket. Below are the relevant details about the Hyundai Verna cigarette lighter: 1. Unscrew the casing: Some car cigarette lighters have a screw-on casing behind the socket, which can be unscrewed by turning it counterclockwise and then screwed back on by turning it clockwise. 2. Remove screws: Some car cigarette lighters are fixed with screws behind the socket. Simply use a wrench to remove the screws to take it off, and then screw them back on to reinstall it. 3. Remove the panel: Remove the gear shift lever panel, which is held by plastic clips. You can pry one side up with your hands or a flathead screwdriver to remove the entire panel. 4. Remove panel screws: After removing the gear shift lever panel, the cigarette lighter panel door will automatically open. You will then see two black screws, which can be removed using an M4 hex wrench. 5. Remove the panel box: Simply pull out the plastic panel box of the cigarette lighter by hand. When it is pulled out about 10 cm, disconnect the wiring first before pulling out the entire box. 6. Operate the inner and outer rings: The cigarette lighter consists of an outer ring and an inner ring. Press the inner ring in when using it. Once it reaches a certain temperature, the inner ring will automatically pop back to its original position. At this point, you can pull it out by holding the outer ring.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.