···
Log in / Register

How much does a 60V20A battery pack of 5 batteries weigh?

4 Answers
VonLogan
07/29/25 7:55pm

5 batteries of 60V20A weigh around 32 pounds. Parameters of a 60V20Ah electric vehicle: The battery voltage is 60V, and the battery capacity is 20Ah. The motor power of such vehicles is typically around 600-1000W, so an average of 800W is taken as a reference. Additionally, the average speed of these vehicles can reach 40-45km/h. Current of a 60V20Ah electric vehicle: The average steady-state current of a 60V20Ah electric vehicle is approximately 13.3A (motor power/battery voltage = 800W/60V). Subsequently, the theoretical driving time can be calculated to be about 1.5h (battery capacity/average current = 20Ah/13.3A).

Was this review help?
11
2
Share
DiHector
08/14/25 3:43pm

I've helped replace quite a few batteries before. These 60V 20Ah lead-acid batteries each weigh about 35kg because they contain lead plates and electrolyte, giving them high density. Five of them together would be around 175kg, so you need to be extra careful when moving them to avoid straining your back. It's best to work with a partner or use a cart. If a car battery is too heavy, it can affect daily use, so remember to check battery life regularly. Lighter lithium batteries only weigh 15kg but cost more. In short, consider both weight and purpose when choosing a battery to avoid trouble.

Was this review help?
3
0
Share
Expand All
OMaya
10/15/25 8:12am

Last time I replaced the battery myself, the 60V 20Ah model felt quite heavy when lifting a single one, approximately 35kg. If there are 5, it would be around 175kg. Due to the lead-acid material's natural weight, handle it with care for safety. It's recommended to ask for help or use mechanical assistance—don't risk injury to save money. As electric vehicle batteries age with prolonged use, they become even heavier. Regular maintenance is essential to extend their lifespan.

Was this review help?
4
5
Share
Expand All
VonGavin
11/29/25 2:14am

The weight of the battery affects usage. A 60V 20Ah lead-acid battery weighs about 35kg, and five of them would total approximately 175kg. When choosing a battery, excessively heavy ones will increase transportation costs and installation difficulty. Lithium batteries are much lighter but more expensive. It's cost-effective to strike a balance based on needs.

Was this review help?
7
1
Share
Expand All
More Forum Discussions

How to solve the problem of BMW X1 air conditioner not cooling?

First, drive with the windows open for a while to equalize the indoor and outdoor temperatures, then close the windows, turn on the air conditioner's internal circulation mode, and set it to the coldest mode with the highest fan speed. If the car air conditioner can still cool, go to a 4S shop to check if there is a lack of refrigerant (Freon). If it is lacking, Freon can be added. It is best to replace the air filter during seasonal changes and perform a cleaning of the air conditioning ducts. For air conditioning circuit issues, check whether the AC switch on the control panel is malfunctioning, whether the main unit's temperature control circuit is normal, and whether the compressor's electromagnetic coil is engaging properly.
16
5
Share

How to Match the Remote Key for Besturn B70?

Park the car and ensure all four doors are closed. Then, open and close the left front door (the main driver's side door) three times. Within three seconds, insert the key and turn it on and off five times consecutively (without starting the engine). Remove the key and press the unlock and lock buttons on the remote. You should hear a response from the remote. After the remote responds, press the unlock and lock buttons on the new remote. The car may experience remote control confusion at this point, requiring a re-matching process. Ensure all four doors are locked, insert the key, and turn it on and off five times within five seconds. Remove the key and press the unlock and lock buttons on the remote twice to complete the process.
18
2
Share

How to Reset the Maintenance Wrench Light on Buick Encore?

Turn off the ignition switch to cut off the power supply to the car. Press and hold the buttons on the dashboard simultaneously, keeping both trip reset buttons pressed for more than 5 seconds. Turn the key to the second position (accessory mode) without starting the engine, and wait until all dashboard lights illuminate. This process typically takes about 10 seconds. Wait for the wrench light to go off. Once it's off, release both trip reset buttons. Turn off the ignition switch and then turn it back on to complete the maintenance reset.
17
1
Share

How to Fix Abnormal Power Window Operation in Honda Vezel?

Open the door where the switch needs to be replaced. For most models, the power window switch area is made of plastic. Carefully examine the seam between the trim panel and door panel to locate the notch. Insert a pry tool or flat tool into the notch to lift the trim panel, then slowly remove the panel along the gap. Disconnect the power window switch connector. Flip the trim panel over, and you should see the switch secured by several cross-head screws. Remove these screws to detach the power window switch. Install the new power window switch, tighten the screws, and reconnect the connector. Test the window operation first to confirm the switch functions properly before reinstalling the trim panel.
8
2
Share

How to remove the fuel pump of Honda CRV?

Remove the rear seat of the Honda Fit vehicle, and use a flat-head screwdriver to pry open the cover plate of the Honda CRV fuel pump. Take off the cover plate of the Honda CRV fuel pump and unplug the connector of the Honda CRV fuel pump. Disconnect the fuel inlet pipe of the Honda Fit, then remove the entire fuel pump of the Honda CRV. Be extremely careful to avoid any open flames or sparks during the process. During installation, note that there are two very small oil drain holes on both sides of the fuel pump base, and no oil should drip from them. Since the fuel pump is immersed in gasoline for a long time, the sealing ring is prone to aging. When installing the fuel pump, check whether the sealing rings on the inlet and outlet pipes are aged or worn.
2
1
Share

How to Replace the Wiper Switch Assembly on a Buick Excelle?

During disassembly, first push the wiper towards the base of the wiper arm. Once it is completely detached from the wiper arm interface, pull it out in the opposite direction. Before pulling it out, rotate the movable wiper blade slightly; otherwise, it may encounter resistance during removal. Installation follows the reverse order of disassembly. First, insert the wiper interface into the wiper arm. During this step, the wiper arm clip must pass through the wiper frame. Then, pull the U-shaped connector upwards into the U-shaped clip. If you hear a crisp "click" sound, it indicates that the installation is properly seated. After installing the new motor, it is advisable to first plug in the power connector to test whether it operates normally.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.