How many years does a vehicle require biennial inspection?

1 Answers
AlexAnn
07/30/25 12:56am
Small and micro non-operational passenger vehicles require inspection once every 2 years within the first 6 years. Biennial inspection: The regulations indicate that for non-operational small and micro passenger vehicles aged 6-10 years, the annual inspection cycle has been adjusted from once a year to once every two years. Six-year exemption from inspection: Non-operational small and micro passenger vehicles with 7-9 seats will be included in the exemption from inspection. This means that non-operational small and micro passenger vehicles with 7-9 seats whose inspection period falls after November 20, 2020, if they meet the conditions, can participate in the annual inspection according to the new policy. Vehicles within the first 6 years can enjoy the exemption from inspection policy and can apply for the inspection compliance label as per the regulations.
Was this review help?
14
1
Share
More Forum Discussions

How to remove the accelerator pedal of Infiniti G25?

Open the hood, remove the engine cover. There are two screws in the middle for adjusting the level to improve the accelerator sticking. Remove these two screws. On the right side of the engine, the red line indicates the path of the accelerator cable. It is easy to remove and install. The accelerator cable passes through the cabin from here, remove it. After both are removed, the accelerator pedal can be easily taken off.
2
0
Share

Is the red wire positive or negative?

Red wires are generally positive. Below is relevant information about the two electrodes: 1. In physics: The positive electrode refers to the end with higher potential (electric potential) in a power source, opposite to the negative electrode. From a physical perspective, it is the pole from which electrons flow out in a circuit. 2. In chemistry: In a primary cell, the device acts as a power source, and the electrode with higher potential from which current flows out is the positive electrode. This electrode serves a reduction function, meaning ions or molecules gain electrons. In an electrolytic cell, the device acts as an electrical appliance, and the electrode connected to the positive terminal of the power source serves an oxidation function, meaning ions or molecules lose electrons, which differs from a primary cell. Two conductors with different reactivity serve as electrodes, maintaining contact and inserted into an electrolyte solution (circuit). The overall reaction is a spontaneous (energy-releasing) redox reaction.
9
3
Share

How to Reset the Tire Pressure Light on Infiniti FX35?

Press the "MENU" button on the turn signal lever, navigate to the "Tire Pressure Display" option in the "Mileage and Fuel Information Menu," and then press the Set-Clr button. Select "Yes" and press the Set-Clr button. The horn will sound twice, and the Driver Information Center will display "Tire Pressure Learning Enabled." Increase or decrease the tire pressure by 8.3 Kpa. Stop the pressure adjustment once the horn sounds. After completing the operation for all four tires, the turn signal will stay on for 3 seconds, indicating the tire pressure learning is complete. Adjust the tire pressure to the desired value to reset the light.
6
1
Share

How to Operate the Infiniti Navigation System?

First, turn on the navigation switch button, then click the menu bar button where the finger is pointing below, and open the second item in the navigation bar. The system will enter the navigation interface, and then determine the location based on satellite positioning, allowing you to search for the destination you want to reach.
11
4
Share

How to Set Up the Infiniti Rearview Camera?

Simply connect the wiring for the rearview camera properly, and the camera view will automatically switch on when reversing. Turn on the vehicle's screen to display a clear view of the area behind the car. The rearview camera also uses lines to indicate the distance of specific objects.
14
5
Share

How to remove the water pump of Infiniti Q50L?

Clean the dirt on the surface of the water pump, remove the slotted nut at the front end of the water pump shaft, and use a special puller to remove the pulley hub and the half-round key. Remove the water pump cover and gasket, then dismantle the water pump impeller according to its structural features using appropriate methods, and press out the water pump shaft with a special tool. After soaking the pump body in hot water at about 85°C, press out the water pump bearing with a special tool. Then, take out the water seal assembly.
2
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.