How Many Years Can a Car Smart Key Battery Last?

2 Answers
AvaFitz
07/29/25 2:20am
Car smart key batteries generally last two to three years. Below are the detailed specifications of car key batteries: Car key battery models: The battery consists of three three-volt button cells or one 9-volt battery. Method for replacing car key button batteries: Remove the hidden mechanical key from the remote, insert it into the marked position, then use a lever motion to lift the key casing. Remove the old battery, install the new one, reattach the key cover by pressing it firmly, ensuring the battery polarity is correct (positive and negative terminals must not be reversed). Finally, reinsert the mechanical key.
Was this review help?
1
4
Share
LolaDella
08/12/25 6:18am
I've been driving for ten years, and the battery life of smart keys is roughly one to three years, depending on how you use them. My first key suddenly stopped working after two years, and I only realized it when the red warning light flashed on the dashboard. I press the lock button frequently, especially after parking—I often press it a few times to confirm, which drains the battery faster. Additionally, temperature extremes have a big impact; the battery drains quicker in winter. I recommend paying attention to the key's indicator light—if it flashes red, it's a low-battery signal. Don’t wait until it’s completely dead and causes trouble. Replacing the battery yourself is simple: just buy a CR2032 coin cell battery for a few bucks at the supermarket, pry open the back cover, and swap it in. I keep a spare in my car just in case. Overall, don’t worry too much—just check it periodically.
Was this review help?
11
2
Share
Expand All
More Forum Discussions

What is the working principle of the clutch pressure plate?

The clutch housing, including the intermediate pressure plate, is mounted on the plunger at the rear end face of the flywheel. Under the action of the spring, the pressure plate engages with the friction disc, transmitting the engine power to the gearbox. Here is more information about the clutch pressure plate: 1. Maintenance and inspection: After grinding, the pressure plate should undergo a balance test, with an imbalance error not exceeding 50g.cm; the clearance of the pressure plate should be checked, and the clearance between the drive pin holes of the intermediate pressure plate of a double-disc clutch and the drive pins should not exceed 1mm; the depth of wear grooves should be measured, and if the depth exceeds 0.50mm, a new part should be replaced. 2. Brief description: The clutch pressure plate is an important component of the clutch, and its function plays a crucial role in the safety of vehicle operation.
20
3
Share

What is the maintenance interval for the RX5?

The maintenance interval for the RX5 is every 5,000 kilometers or 3 months. Car maintenance involves regular inspection, upkeep, and cleaning to prevent potential hazards caused by component issues and to keep the vehicle's performance at a high level. In general, car maintenance helps eliminate all unknown risks and extends the vehicle's usable lifespan. The Roewe RX5 is a compact SUV with dimensions of 4556mm in length, 1855mm in width, and 1719mm in height, and a wheelbase of 2700mm. It is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 169 PS, a maximum torque of 250 Nm, and a maximum power of 124 kW, paired with a 6-speed manual transmission.
12
0
Share

What are the main components of the piston connecting rod assembly?

The piston connecting rod assembly mainly consists of the piston, piston rings, piston pin, connecting rod, and connecting rod bearing. The piston connecting rod assembly converts the reciprocating motion of the piston into the rotational motion of the crankshaft, while transforming the force acting on the piston into the torque output by the crankshaft to drive the vehicle's wheels. It serves as the transmission component of the engine, transmitting the pressure of the combustion gases to the crankshaft, causing the crankshaft to rotate and output power. Precautions for using the piston connecting rod assembly include: 1. Check the directionality of the piston and connecting rod before assembly; 2. Use special tools or heat to 60 degrees when installing the piston pin; 3. Pay attention to the cylinder markings when disassembling and installing the piston, and make marks if there are no existing markings.
9
0
Share

What is the installation method for the Focus radiator lower guard?

The installation method for the Focus radiator lower guard is: remove and set aside the bottom guard plate screws, then install the new guard plate and tighten the screws. The car radiator generally refers to the cooling radiator, which is part of the vehicle's cooling system. The radiator in the engine water cooling system consists of three parts: the inlet chamber, outlet chamber, main plate, and radiator core. The Focus is a compact car with dimensions of 4378mm in length, 1810mm in width, and 1468mm in height, a wheelbase of 2705mm, a fuel tank capacity of 53 liters, and a curb weight of 1242kg. The Focus features a MacPherson strut front suspension and a torsion beam rear suspension.
14
2
Share

What is the symbol for the auto start-stop function?

The symbol for the auto start-stop button is: an unclosed circle with a small arrow on it and the letter A inside the circle. The engine auto start-stop function automatically shuts off the engine when the vehicle comes to a temporary stop (e.g., at a red light) during driving. When it's time to move forward again, the system automatically restarts the engine. More related information is as follows: 1. How the start-stop system works: When the vehicle stops due to traffic congestion or at an intersection, and the driver presses the brake pedal and shifts to neutral, the engine automatically stops running once these three conditions are met. 2. The working state of the start-stop system: When the vehicle is in a stopped state (not in park), the engine will pause operation (instead of maintaining traditional idle speed). During this pause, the lubricating oil inside the engine continues to circulate, keeping the engine internally lubricated.
10
2
Share

What grade of gasoline does the Golf 1.2T use?

The Golf 1.2T uses 95-octane gasoline. Gasoline is a volatile and flammable hydrocarbon mixture liquid derived from the distillation, cracking, or pyrolysis of petroleum. It is primarily used as fuel for spark-ignited internal combustion engines and mainly consists of organic compounds obtained from crude oil distillation and various additives. The Golf is a compact car with dimensions of 4296mm in length, 1788mm in width, and 1471mm in height, a wheelbase of 2636mm, and a fuel tank capacity of 51 liters. It is equipped with a 1.2T turbocharged engine that delivers a maximum horsepower of 116 PS, a maximum power output of 85 kW, and a peak torque of 200 Nm, paired with a 7-speed dual-clutch transmission.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.