How Many Years Can a Camry Last?

1 Answers
OEmiliano
07/29/25 11:40am
Camry can last for 15 years or more. Here is more information about the Camry: 1. The Camry is a model under GAC Toyota, belonging to the mid-to-high-end segment and is a popular choice among many consumers. 2. In terms of exterior design, the new Camry features dual styling with a luxury version and a sport version. The luxury version adopts a large trapezoidal horizontal grille, a streamlined body posture, and a lower waistline. The extended roof rear section increases rear headroom. The sport version features a three-layer grille front face, debuting a two-tone body color and an all-black cabin design, with a dual-sided quad-exhaust tailpipe layout. 3. For the interior, it employs an asymmetrical design with a Y-shaped curve on the center console. The soft-touch interior surfaces and metal trim panels use premium materials. For the first time, a three-dimensional surface decoration process is applied to the instrument panel and console trim, creating a visual 3D effect. The seats feature a sporty three-dimensional design, using new springs and high-density, high-damping polyurethane material for the seat cushions.
Was this review help?
15
2
Share
More Forum Discussions

Is a Dash Cam Easy to Install?

Whether a dash cam is easy to install depends on its structure. A single-lens dash cam is relatively simple to install, while a dual-lens dash cam is more complex. Below are the detailed installation steps: Dash Cam Installation Methods: For a single-lens dash cam, first determine the mounting position. Then route the cable along the inner edge of the roof trim, follow the rubber lining of the A-pillar, and run the wire along the floor mat or storage compartment to the cigarette lighter for power connection. On the other hand, installing a dual-lens dash cam involves more steps, including a longer power routing path and the need to remove more interior trim pieces. Therefore, it is recommended that owners visit a 4S shop for professional installation. Dash Cam Installation Notes: Since the distance between the camera and the dash cam body is significant, cable routing is the most complex part of the installation. To conceal the wiring, you can tuck the cable into the gap between the car body and the headliner from the rear, then route it along the gap between the windshield and the headliner at the front. Alternatively, you can run the cable under the cabin and hide it with the floor mat, though the power cable will inevitably be exposed at the front.
15
2
Share

What is the weight of the Levin?

The Levin has 13 models currently on sale, with a curb weight ranging between 1320-1430kg. It is a 4-door, 5-seater sedan with dimensions of 4640*1780*1455mm (length*width*height). In the same class, the Xingrui 2021 model has a curb weight of 1500kg. In terms of powertrain, the Levin 2022 185T series offers three models: Tech Edition, Sport Edition, and Luxury Edition. All are equipped with a 1.2L turbocharged engine and E-CVT continuously variable transmission. The engines feature 4 cylinders in a transverse layout, with front-wheel drive configuration. For other configurations, all or some models of the Levin 2022 185T series come with features including driver/passenger airbags, front/rear curtain airbags, ISOFIX child seat anchors, driving assistance imaging, rear cross-traffic alert, and drive mode selection. Note that this generation Corolla has two versions in China: FAW Corolla and Toyota Levin. The new Levin's Sport Edition adds a sport package featuring front/rear aerodynamic bumpers, a sporty mesh piano-black front grille, and sport-style exclusive seats. The gasoline Sport Edition also adopts a lowered body stance.
2
5
Share

What to do if the STOP light on FAW truck stays on?

If the STOP light on a FAW truck remains illuminated, you should check the water temperature, oil pressure, air pressure, engine, cab, etc. The STOP light will activate if any of these components malfunctions. Below is an introduction to the STOP light: 1. This light is connected to warning lights such as "oil pressure" and "brake fluid level" as well as the "coolant temperature gauge." If the light flashes while the engine is running, you must immediately stop and turn off the engine. 2. The oil pressure warning light is connected to the central STOP warning light. If this indicator lights up while the engine is running, accompanied by a buzzer sound, and the multifunction display shows "OIL-PRESSURE-INSUFFICIENT (engine oil pressure too low)," stop immediately. If the lubrication system is low on oil, refill it to the proper level. 3. The parking brake and low brake fluid level warning lights are connected to the STOP warning light. This light will illuminate every time the ignition switch is turned on.
20
5
Share

What to Pay Attention to When Taking Delivery of a Car?

When taking delivery of a car, it is necessary to check the engine, exterior scratches, and other aspects. Below are the specific precautions for vehicle inspection upon delivery: Inspect the body: Visually examine the paint surface of the car body to check for scratches and wear. Observe under sufficient sunlight to see if there is any color difference in the paint. Open the car door and push it to several angles to allow light to shine from different directions, checking if the sheet metal is even. Check the doors: Open the car doors and pay attention to whether they open and close smoothly. Check if the gaps between the doors and between the front and rear bumpers are consistent. Inspect the engine: Open the engine hood and check if the engine compartment is clean. If the car has been stored for a long time or used, there may be obvious dust or stains in some areas. Check the glass: Check if the windshield is original. Check the vehicle nameplate: The car nameplate is located on the side of the driver's door or inside the engine compartment. Pay attention to whether the manufacturing date is too far from the current date. If it exceeds six months, the car is likely to be a stock vehicle or a test drive car.
2
0
Share

What does TC stand for?

TC in a car stands for Traction Control System. Here is some relevant information: Introduction to Traction Control System: The Traction Control System, also known as the Anti-Slip Regulation system. When a car brakes on a slippery surface, the wheels may skid, and the direction may even become uncontrollable. When the car starts or accelerates rapidly, the drive wheels may also skid, and on slippery surfaces such as ice and snow, this can lead to dangerous loss of control. The Traction Control System is designed to address this issue. The system relies on electronic sensors to detect when the driven wheels are moving slower than the drive wheels. It then sends a signal to adjust ignition timing, reduce throttle opening, decrease fuel supply, downshift, or apply brakes to the wheels, thereby preventing wheel skidding. How the Traction Control System Works: The Traction Control System works by replacing the mechanical connection between the accelerator pedal and the throttle with an electronic throttle control device. Sensors transmit the accelerator pedal's information to the ECU. The ECU then generates a control voltage signal based on this input. A servo motor adjusts the throttle according to this signal, reducing throttle opening and controlling wheel skidding. For drivers operating their vehicles in rainy or snowy conditions, this system can help minimize skidding or loss of control.
1
3
Share

How to Avoid the Rear of the Car Exceeding the Line When Reversing into a Parking Space?

Methods to avoid the rear of the car exceeding the line when reversing into a parking space include: 1. When reversing to the right, slightly adjust the steering wheel to the left instead of turning it all the way to the right; 2. Continue reversing and straighten the wheel when the left side of the car is almost parallel to the left side of the parking space; 3. Make minor adjustments after entering the parking space—steer in the direction the rear of the car is leaning; 4. If the steering is turned too early, the angle between the wheels and the right side of the parking space will be small; 5. If continuing to reverse would cause the car to hit the right side of the parking space, straighten the wheel in time and reverse a bit further; 6. When the left side of the car is almost parallel to the left boundary line of the parking space, straighten the wheel. Reversing into a parking space is a mandatory test item for obtaining a small car driver's license, assessing the driver's ability to maneuver the vehicle in a confined space. It is a key evaluation point in the driver's test, requiring the driver to correctly reverse the vehicle into the parking space from both sides while in motion.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.