How many points are deducted for crossing solid lines and changing lanes on the highway?

2 Answers
VanNoah
07/29/25 12:27am
Crossing solid lines and changing lanes on the highway results in a deduction of 3 points and a fine of 200 yuan. During the operation of a motor vehicle, actions such as crossing lines, straddling lines, or crossing single or double solid yellow lines, parking in no-parking zones either temporarily or for an extended period, making U-turns in no-U-turn zones, or making left turns at intersections where left turns are prohibited, all constitute violations of prohibited traffic markings. If a motor vehicle driver commits any of the following violations, they will be penalized with a deduction of 3 points: 1. Driving a motor vehicle on the highway below the prescribed minimum speed limit; 2. Driving a motor vehicle prohibited from entering the highway onto the highway; 3. Driving a motor vehicle on the highway or urban expressway without following the designated lane; 4. Failing to slow down, stop, or yield to pedestrians at crosswalks while driving a motor vehicle; 5. Driving a motor vehicle in violation of prohibitory signs or markings.
Was this review help?
15
2
Share
LaneAnn
08/12/25 4:41am
After driving for so many years, I've seen plenty of cases of crossing solid lines to change lanes on highways, especially in congested areas where everyone gets impatient to switch lanes. Last winter on the Beijing-Hong Kong-Macao Expressway, I was in a hurry and crossed a solid line to change lanes once—what happened? I got caught by the surveillance camera immediately, lost 3 points, and was fined 200 yuan. The solid lines on highways aren’t meant to be crossed casually because lane divisions are there to prevent chaos and accidents. Imagine driving at such high speeds—a sudden lane change could easily cause a rear-end collision. I’ve personally witnessed minor accidents like that. So, I advise everyone to strictly follow the lane markings and assess the road conditions hundreds of meters ahead. Developing good habits not only avoids penalties but also ensures safety. Nowadays, navigation devices are smart enough to give early warnings about lane changes—make full use of them to minimize mistakes.
Was this review help?
12
4
Share
Expand All
More Forum Discussions

What is the maximum load capacity for a total mass of 4490kg?

A total mass of 4490 kilograms can carry a load of 1730 kilograms. Pre-departure vehicle inspection: Before setting off each day, conduct a comprehensive inspection of the vehicle, including checking for oil or water leaks; measure tire pressure to ensure it is appropriate; check the engine oil condition; inspect the spare tire for integrity, etc. Caution when wading: If encountering waterlogged roads, assess the water depth and underwater road conditions to determine if it exceeds the vehicle's passing capability. Avoid attempting to wade through water deeper than half the height of the car tires. Adhere to traffic rules: Do not race with other vehicles; drive safely in accordance with traffic regulations and yield to pedestrians. Maintain a safe following distance by staying in the right rear corner of the vehicle ahead; when overtaking, pass from the left side of the vehicle in front, avoiding overtaking on the right or between two parallel vehicles.
7
1
Share

What are the common faults of car power windows?

Common faults of car power windows: 1. The reason why the electric switch window does not move smoothly is mostly due to the exhaustion of oil in the door internal lifter, the inner cover should be removed and oil should be added; 2. If the glass cannot move at all, it may be a switch failure and can only be replaced; 3. If the electronic device does not work, check the fuse, the fuse is used for the power window; 4. When the switch action becomes worse and the window cannot be opened smoothly, the possibility of switch failure is very high; 5. Before oiling the internal mechanical device, first remove the inner cover, remove the hidden screws, and disassemble the quick switch; 6. Remove the inner cover, peel off the plastic paper for waterproofing below, and expose the lifting mechanism of the window; 7. Spray grease on the arm fulcrum and inside the gear, and spray while moving up and down, so that very small parts can also be coated.
17
0
Share

How Many Degrees to Turn the Steering Wheel for Right or Left Turns?

Turn the steering wheel approximately 150 to 160 degrees for right or left turns. Scenarios requiring yielding right of way: When traffic signs or markings indicate priority, yield to the party with the right of way; in the absence of traffic signs or markings, come to a complete stop before entering the intersection to observe and yield to vehicles approaching from the right; turning vehicles must yield to vehicles going straight; for vehicles approaching from opposite directions, those turning right must yield to those turning left. Prohibited actions while driving: Motor vehicles are prohibited from reversing at railway crossings, intersections, one-way roads, bridges, sharp curves, steep slopes, or tunnels. Motor vehicles may make U-turns at locations without no-U-turn or no-left-turn signs or markings, provided they do not impede the normal flow of other vehicles or pedestrians.
14
3
Share

Where is the cabin air filter located in the Passat?

The cabin air filter in the Passat is located under the glove compartment on the passenger side. There is an external cover panel that needs to be removed to access the cabin air filter housing cover. After removing this cover, you can replace the cabin air filter. The cabin air filter is a crucial component of the air conditioning system and requires regular replacement. The Passat measures 4870mm in length, 1834mm in width, and 1472mm in height, with a wheelbase of 2803mm. The Passat is equipped with three engine options: a 1.4T and two 2.0T engines (high and low power versions), and offers National V, National VI emission standards as well as a plug-in hybrid variant. The Passat 430PHEV model delivers a combined maximum power output of 211 kW with a peak torque of 400 Nm, paired with a 6-speed wet dual-clutch transmission, achieving a 0-100 km/h acceleration time of 7.8 seconds.
15
0
Share

What is the reason for water dripping from the right front wheel?

The reason for water dripping from the right front wheel is: the car's air conditioning is turned on. Select the appropriate fan speed setting: During normal operation of the car, to prevent excessive frosting of the evaporator, which affects the operation of the air conditioning system, the air supply speed and temperature control should not be set to the lowest for a long time. When the speed is below 25 km/h, the fan speed switch should be set to the low-speed setting to avoid insufficient power generation and insufficient cooling. Single use time of air conditioning: If the temperature inside the car has reached a comfortable level, the air conditioning can be turned off, or turned on again after a while. Prolonged use of the air conditioning will cause excessive pressure on the condenser, which will cause damage to the refrigeration system. Therefore, the air conditioning should not be used for too long each time.
18
4
Share

What to do if the reversing camera sometimes works and sometimes doesn't?

Check whether the reversing light is on. If it is not on, check the reversing fuse or wiring. If it is on, check the reversing camera wiring or the camera itself. Here is an introduction to the reversing camera: 1. Introduction: The reversing camera, also known as the parking assist system, or the reversing visual system, or the on-board monitoring system, is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Purpose: After years of development, the reversing radar system has upgraded its technology, improved its performance, and been applied to various types of vehicles, such as trucks, buses, school buses, combine harvesters, corn harvesters, coaches, and engineering machinery. 3. Advantages: Installation is simple. Generally, a single-output reversing camera only requires connecting the positive power wire to the positive terminal of the reversing light power supply, and the negative power wire to the negative terminal of the reversing light or to the ground (GND). The wiring can be easily understood by studying the vehicle model, and the camera can be installed by drilling a hole in an easy-to-install position.
4
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.