How Many Minutes Is the Most Correct for Warming Up the Car in Summer?

3 Answers
DeIsabel
07/24/25 9:20pm
In summer, warming up the car only requires 10 to 30 seconds. Here are the reasons why warming up is necessary: 1. The upper part of the engine lacks oil and lubrication after prolonged parking: After the car has been parked for a long time, the engine oil flows back to the oil pan at the lower part of the engine. Therefore, when starting the engine after not using the car for a while (such as overnight), the upper part of the engine is in a state without oil and lacks lubrication. It takes about 10 seconds after starting for the oil pump to circulate the oil to the parts that need lubrication the most, such as the pistons, connecting rods, and crankshaft. 2. The fuel supply system is still at a low temperature and cannot effectively vaporize gasoline completely: Before the engine reaches its operating temperature (approximately between 90-110 degrees Celsius), the fuel supply system, due to its low temperature, cannot effectively vaporize gasoline completely. When gasoline is still in a 'wet' liquid state and not vaporized, it is difficult to ignite and start the engine.
Was this review help?
11
3
Share
ColeDella
08/10/25 9:42am
I've been driving for over twenty years, and in summer, there's no need to wait several minutes to warm up the car. In fact, after starting the engine, just wait 10 seconds to half a minute to let the oil circulate, and then you can drive. Idling for too long is actually harmful, wasting fuel and causing the engine to overheat and accumulate carbon deposits. In summer, the high temperature ensures good oil fluidity, so the warm-up time is very short. My habit is to wait briefly after starting and then drive at low speed, avoiding heavy throttle, allowing the engine to warm up evenly while running. This not only protects the car and extends its lifespan but also saves fuel and ensures safety. During every maintenance check, inspect the oil condition to ensure the lubrication system is functioning properly, so the car won't have major issues.
Was this review help?
13
3
Share
Expand All
LaEli
09/26/25 5:25am
As an environmental enthusiast, I never delay warming up my car in summer. I start driving after just about 10 seconds of idling. Keeping the engine running for several minutes to warm up is unnecessary and just wastes fuel while emitting exhaust gases, which is not eco-friendly. The engine warms up more efficiently while in motion, and the oil heats up quickly in summer, so a short warm-up period is sufficient. I recommend gently pressing the accelerator and driving slowly for a few minutes. This saves fuel, reduces pollution, and protects the engine from wear and tear. Developing good habits and not wasting time idling is safe and responsible—good for both your car and the planet.
Was this review help?
7
5
Share
Expand All
More Forum Discussions

How to Correctly Step on the Accelerator and Clutch in Subject Three?

Subject Three: The correct method of stepping on the accelerator and clutch is introduced as follows: 1. Seat adjustment: Adjust the seat. Many people forget to adjust the seat before the test, resulting in discomfort all over the body, or even inability to see the reference points clearly. To control the clutch and accelerator, place your right foot on the accelerator pedal, ensuring it feels comfortable—neither too far to reach nor too crowded. Both hands should rest comfortably on the top of the steering wheel. 2. Foot posture: Place the heel of your right foot on the floor of the driver's compartment as a pivot point, with the ball of your foot resting on the pedal. Use the strength of your ankle joint to move back and forth, ensuring it feels comfortable—discomfort is not acceptable. 3. Starting: First, press the clutch all the way down, shift into first gear, and then slowly release the clutch until the car noticeably vibrates. Releasing it too quickly will cause the engine to stall. At this point, gently press the accelerator with your right foot in sync with the vehicle's speed—press it slowly, as pressing too hard will cause the car to jerk forward. Once the clutch is fully released, the car will start smoothly. 4. Shifting gears: Upshifting: Before upshifting, ensure coordination between the accelerator and clutch. First, release the clutch, then press the accelerator, allowing the speed to increase gradually—avoid pressing the accelerator abruptly. Downshifting: If the speed is too high, lightly press the brake before downshifting.
3
2
Share

Should You Use a Low or High Gear on Bumpy Roads?

When driving on bumpy roads, the correct approach is to shift to a lower gear and gradually release the accelerator pedal. Gradually releasing the accelerator pedal allows the vehicle to pass through the bumpy section smoothly at a low speed, enabling the car to move forward at idle. Shifting to a lower gear provides more engine traction. More details are as follows: 1. Reason for choosing a lower gear: Selecting a lower gear is because when driving on uneven roads, using a low gear at idle or with slight acceleration can reduce the impact from the rough surface and alleviate body vibrations. 2. Reason for gradually releasing the accelerator: Gradually releasing the accelerator is necessary because when the vehicle is moving slowly, a sudden release of the accelerator can cause jerking, which affects the vehicle's transmission components. Therefore, in normal operation, slowly releasing the accelerator pedal helps avoid jerking.
9
4
Share

How to Determine if a Torque Converter is Faulty?

Torque converter faults can be identified through the following symptoms: 1. Torque converter overheating: Overheating causes a decrease in transmission oil viscosity and damage to rubber oil seals, resulting in loss of lubrication and oil leakage. It also leads to insufficient power in loaders and deterioration of torque converter performance, which is one of the most common fault phenomena. Common causes include: insufficient oil supply from the hydraulic pump, faults in the cooling system, incorrect or degraded oil type, oil pressure in the torque converter being lower than the adjustment pressure of the main pressure valve, and excessively low outlet pressure of the torque converter. Another reason could be poor structural design of the torque converter, leading to abnormal wear. 2. Insufficient output of the hydraulic torque converter and driving force of the loader: When the loader operates at low speed, the diesel engine's power is transmitted from the pump wheel to the turbine, while the guide wheel remains stationary. The reaction torque generated by the guide wheel combines with the torque from each pump wheel and is transmitted to the turbine, providing speed reduction and torque increase, ensuring driving force under low-speed and heavy-load conditions. If the overrunning clutch is damaged, the engine's torque can only be transmitted through a single guide wheel or directly to the turbine, reducing torque conversion efficiency and causing insufficient power. This may even eliminate the speed reduction and torque increase effect, and stepping on the accelerator in this condition could cause the engine to stall.
19
1
Share

What are the penalties for a 5-seater private car carrying 6 people?

For a 5-seater private car carrying 6 people, the penalty is 3 demerit points and a fine of 100 RMB. Below are relevant details about driving private cars: 1. Explanation: For driving non-commercial vehicles, exceeding the approved number of passengers by less than 20% results in 3 demerit points and a fine of 100 RMB; exceeding by 20% or more results in 6 demerit points and a fine of 200 RMB. 2. Hazards of overloading: (1) Vehicle overloading severely damages road infrastructure. Since overloaded vehicles far exceed the design load of roads and bridges, it leads to pavement damage, bridge fractures, and significantly shortens their service life. (2) Overloaded vehicles have increased mass and inertia, leading to longer braking distances and higher risks. Severe overloading can cause tire blowouts, sudden swerving, brake failure, rollovers, and other accidents due to excessive tire load and deformation. Additionally, overloading affects the vehicle's steering performance, increasing the likelihood of accidents due to loss of steering control.
15
3
Share

Is it necessary to obtain the vehicle certificate of conformity on the day of picking up the car?

When picking up the car, the 4S store should hand over the certificate of conformity to the car owner. The following is the importance of the vehicle certificate of conformity: 1. Essential document for vehicle registration: The vehicle certificate of conformity is very important as it serves as a credential for the car and is also a necessary document for vehicle registration. In addition, the car purchase invoice, the three-guarantee service card, and the vehicle instruction manual are all important credentials for a new car. If the owner finds any of these documents missing before payment, they should promptly request them from the dealer. 2. Failure to provide the certificate of conformity constitutes a serious breach of contract: The vehicle certificate of conformity must be provided by the 4S store before the car owner makes the payment. From a legal perspective, regardless of any reason, the car certificate of conformity cannot be withheld. If the car dealer delays or refuses to deliver the product certificate of conformity, this behavior constitutes a serious breach of contract, and the owner can request the dealer to terminate the sales contract and compensate for the corresponding losses.
14
4
Share

What are the methods to distinguish genuine from fake used catalytic converters?

Methods to distinguish genuine from fake used catalytic converters are as follows: 1. Pore arrangement: In a normal catalytic converter, the pores of the internal porous ceramic should be uniformly arranged and consistent in size, with the porous ceramic being clean and relatively white (a yellowish beige color indicates a fake). 2. Assembly: The porous ceramic inside the catalytic converter, serving as a carrier, should be firmly and securely assembled with the outer shell, with no signs of looseness (even slight looseness is unacceptable). 3. Dimensions: The replacement catalytic converter should match the original factory dimensions in terms of size, the material of the internal porous ceramic, the arrangement pattern of the pores, and the number of rows. 4. Steel stamp: The encapsulation of the catalytic converter must be performed by an enterprise with nationally recognized environmental qualifications, and the manufacturer's steel stamp must be printed on it.
14
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.