How many minutes are stipulated for Subject Three completion?

2 Answers
LailaFitz
07/29/25 5:10am
There is no time limit for the entire Subject Three test. Completion is based on successfully performing all required operations. It generally takes about ten minutes to finish. The required distance is three kilometers, typically including preparations before starting the vehicle, light simulation, starting off, left and right turns, lane changes, turn signal usage, U-turns, and pulling over. Subject Three consists of 16 items in total. Below are the detailed descriptions: 1. Items include: preparations before starting the vehicle, starting off, driving straight, gear shifting operations, changing lanes, going straight through intersections, passing pedestrian crossings, passing bus stops, passing school zones, left turns at intersections, right turns at intersections, meeting oncoming traffic, overtaking, making U-turns, pulling over, and nighttime driving. 2. Subject Three is part of the motor vehicle driver's license assessment, officially known as the Road Driving Skills and Safe & Civilized Driving Knowledge Test. The safe and civilized driving knowledge test generally includes: requirements for safe and civilized driving operations, safe driving knowledge under adverse weather and complex road conditions, and post-accident handling knowledge.
Was this review help?
10
5
Share
LilaRose
08/12/25 8:47am
When I took the driving test (Subject 3) before, I remember the exam duration was set between 10 to 15 minutes, depending on the test center's regulations. At my urban test site, we were required to complete the entire route within 15 minutes, including starting, straight-line driving, turning, lane changing, and pulling over. Each maneuver had to be executed promptly without delay—exceeding time limits would result in point deductions or even failing the test. For instance, taking too long on turns would prompt the instructor to intervene. During practice, I made a habit of timing myself with my phone, simulating the exam process by running through the course multiple times to refine my pacing—maintaining steady speed (not too fast or slow) was crucial to demonstrating proper driving skills. Though the test duration is brief, consistent practice in speed control ensures smooth completion and boosts confidence.
Was this review help?
2
5
Share
Expand All
More Forum Discussions

Is it mandatory to apply for an ETC card?

It is not mandatory, but car owners are encouraged to apply. According to the regulations of the State Council, vehicles without ETC in 2020 will not enjoy toll discounts. In the future, only one manual lane will be retained at highway toll stations, and tolls can only be paid through manual lanes. Additionally, newly installed ETC devices cannot be used on highways immediately; they must be activated first. During free holiday periods, highways can still be used. For users who have already installed ETC, passing through ETC lanes will not incur charges. The principle of ETC toll deduction: There will be one or more ETC lanes on highways. Through dedicated short-range microwave communication between the vehicle's electronic tag installed on the windshield and the microwave antenna in the ETC lane at the toll station, and using computer networking technology for backend settlement with banks, the system achieves the purpose of vehicles paying tolls without stopping at road and bridge toll stations. All of this is based on the principle of passing first and deducting fees later. Benefits of installing ETC: Time-saving: Eliminates the hassle of waiting in queues; Green and eco-friendly: Low-carbon, as vehicles pass through toll stations without stopping, reducing noise and exhaust emissions and minimizing pollution; Reduced wear and tear: Saves costs by decreasing the frequency of vehicle starts and brakes, lowering wear and fuel consumption; Improved efficiency: Theoretically, ETC lanes can increase vehicle passing efficiency by 2-3 times, making traditional ETC faster, more advanced, and more high-tech. Compared to license plate payment, ETC technology is more mature and advantageous. More policy support: The State Council clearly stated in the "13th Five-Year Plan for the Development of a Modern Comprehensive Transportation System" that "by 2020, intercity transportation cards will be basically interoperable in key city clusters, and the proportion of vehicles using ETC will significantly increase." It also set a clear target in the "13th Five-Year" comprehensive transportation development indicators: "By 2020, the ETC usage rate for road passenger vehicles will reach 50%." More future possibilities: In addition to continuously improving the convenience of ETC installation and usage and increasing the ETC usage rate for passenger vehicles, efforts will be made to promote ETC usage for trucks in the future. There will also be exploration of deeper integration between ETC systems and smart transportation development directions such as vehicle-to-vehicle communication and vehicle-to-road coordination, providing car owners with comprehensive travel services. This means more application scenarios will support ETC applications.
15
5
Share

What causes the ABS warning light to stay on in an old Buick Excelle?

ABS warning lights can indicate various conditions, each with different causes and solutions, as detailed below: Condition 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting its ability to detect speed signals. This prevents the ABS control module from determining vehicle speed or wheel slip rate, thus failing to issue appropriate braking commands. Solution: Clean the wheel speed sensor and adjust the gap between the sensor and tone ring to restore normal function. Cause 2: Loose wiring connections or poor ABS relay contact causing signal issues. Solution: Inspect wiring connections and secure any loose connections. Condition 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: Battery voltage drops below 10.5V when multiple electrical components are in use. The light extinguishes when engine RPM increases and voltage rises. Possible low voltage supply to ABS system due to poor connections or grounding. Solution: Check battery specific gravity, charging system, and power supply (including voltage relay and connections). Condition 3: ABS warning light remains on after engine start until ignition is turned off. Cause: Poor grounding of ABS hydraulic valve body; loose wiring connections at valve body; ABS control module failure. Solution: Loosen and retighten valve body ground screw (clean contact surface if needed); inspect connector gaps; replace ABS or ABS/ASR control module if necessary. Condition 4: ABS warning light illuminates during high-speed driving. Cause: ABS control module detects significant speed difference between front and rear wheels; incorrect tire or wheel specifications. Solution: Verify proper tire and wheel specifications (refer to fuel filler door label). Condition 5: ABS warning light intermittently flashes. Cause: Improper brake light switch adjustment; internal contact issues in brake lights. Solution: With engine running, press brake pedal and manually push switch lever downward to reset position; replace brake light switch if needed. When the ABS warning light is illuminated, continued driving is not recommended. An active ABS fault means the anti-lock braking system is compromised. During emergency braking, locked wheels could cause loss of vehicle control, preventing proper deceleration or steering correction - creating significant safety risks.
15
5
Share

How much refrigerant should be added to a BMW 525?

BMW 525 requires 5 cans of refrigerant for a single refill. Below are the specific details of the BMW 525: 1. Dimensions: The BMW 525 measures 5087mm in length, 1868mm in width, and 1500mm in height, with a wheelbase of 3108mm. 2. Interior: The center console features a 10-inch LCD display, equipped with the latest generation of human-machine interface that supports touchscreen, gesture, voice, and iDrive control methods. The three-spoke multifunction steering wheel is wrapped in genuine leather and also supports voice control, cruise control, and other functions.
3
3
Share

What is the tire model of the Trumpchi GS4?

The tire model of the Trumpchi GS4 is 215/55R18. Tires are circular elastic rubber products installed on various vehicles or machinery to roll on the ground, typically mounted on metal rims. They support the vehicle body, absorb external shocks, ensure contact with the road surface, and maintain the vehicle's driving performance. The dimensions of the Trumpchi GS4 are 4545mm in length, 1856mm in width, and 1668mm in height, with a wheelbase of 2680mm. The Trumpchi GS4 features front-wheel drive, a front MacPherson independent suspension, and a rear multi-link independent suspension.
6
5
Share

How many cylinders does the Volvo S90 engine have?

Volvo S90's engine is a 4-cylinder. An engine is a machine that can convert other forms of energy into mechanical energy, originating in the UK. It can refer to either a power generation device or the entire machine including the power unit, such as a gasoline engine. Engine types include internal combustion engines, external combustion engines, and electric motors. The Volvo S90 has dimensions of 5090mm in length, 1879mm in width, and 1450mm in height, with a wheelbase of 3061mm. It is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 250ps, maximum power of 184kw, and maximum torque of 350nm.
15
5
Share

How to Adjust Turbocharger Pressure?

Here is the relevant introduction on adjusting turbocharger pressure: 1. Setting bypass valves: In the automotive turbocharging system, setting intake and exhaust bypass valves is the simplest, lowest-cost, and highly effective method to regulate boost pressure. 2. Low-pressure situation: When the compressor outlet pressure, i.e., the boost pressure, is below the specified limit, the diaphragm moves upward under the action of the diaphragm spring, and the linkage rod closes the exhaust bypass valve. When the boost pressure exceeds the specified limit, the boost pressure overcomes the diaphragm spring force, pushes the diaphragm downward, and the linkage rod opens the exhaust bypass valve, allowing part of the exhaust to bypass the turbine and directly enter the exhaust manifold, thereby controlling the boost pressure and turbine speed.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.