How Many Liters of Transmission Oil Does the Vezel Require?

How to Turn Off the Auto Start-Stop Function in a Car?

To turn off the auto start-stop function, you need to press the auto start-stop off button each time after starting the vehicle. The vehicle's dashboard will then display that the auto start-stop function has been deactivated, along with an icon indicating the function is off. Here are some details about the auto start-stop function: 1. The auto start-stop function automatically shuts off the engine when the vehicle comes to a temporary stop (e.g., at a red light) and restarts it when it's time to move again. 2. Disadvantages of using the auto start-stop function: It creates noise and vibrations, affecting the driving experience; it operates unevenly, with noticeable gaps, causing discomfort over time; the specialized battery for auto start-stop is expensive; the function is not very intelligent and often activates or deactivates unnecessarily.

13

2

Share

Replacement Cycle of Antifreeze for Hyundai Elantra

The antifreeze for the Elantra should be replaced every two years. This is just a reference cycle. For commercial vehicles with higher mileage, the replacement cycle should be shorter. Since driving conditions vary for each vehicle, the replacement should be based on actual usage. Regularly check the antifreeze level and replenish it promptly if it is insufficient. If suspended matter, sediment, or signs of deterioration or discoloration are found in the antifreeze, it should be replaced immediately, and the system should be cleaned. Method for replacing antifreeze: Before completely replacing the antifreeze, conduct a thorough inspection to check for any leaks or cracks in the pipes, with a focus on the five-way hose. The five-way hose is named for its five connections to different parts of the vehicle. Antifreeze flows through the five-way hose and is distributed to various parts of the car to function. If there are signs of antifreeze leakage in this area, replace the hose or resecure the connections as needed. Drain the old antifreeze, then flush the fluid channels with clean water. Add clean water to the antifreeze reservoir and continue filling until water flows continuously through the engine cooling system. Then, start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the water draining from the reservoir may appear slightly pink. Continue adding clean water until the water runs clear. Note: Remember to remove the heater hose and drain the water from the heater core. After draining for about an hour, add the new antifreeze through the radiator hose to allow it to flow quickly into the radiator. Then, add another bottle of antifreeze to the reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. As some air is expelled from the cooling system, the fluid level will drop. Add more antifreeze until it reaches the "MAXT" mark on the reservoir.

5

2

Share

What Are the Reasons for Low Idle Speed During Cold Start?

Reasons for low idle speed during cold start include: carbon buildup in the throttle body, dirty intake passages, and weak spark due to faulty spark plugs, which should be cleaned or replaced promptly. Below are detailed explanations of the related causes: 1. Prolonged vehicle usage can lead to clogged intake passages, carbon deposits or oil accumulation in the throttle body, resulting in unstable or low idle speed. Carbon buildup in the throttle body affects air intake, causing low idle speed during cold starts. It is recommended to clean the throttle body and intake passages to prevent abnormal idle conditions. 2. Over time, spark plugs can also accumulate carbon deposits. Severe carbon buildup may cause weak sparks in some cylinders, affecting vehicle performance and leading to low idle speed. Timely cleaning or replacement of spark plugs is advised. 3. A clogged fuel injector can cause insufficient fuel pressure and poor fuel atomization, leading to unstable or low idle speed. If the vehicle's intake pipe malfunctions, the air-fuel mixture ratio may become imbalanced, potentially causing excessive emissions and failure to pass annual vehicle inspections.

8

1

Share

What Causes the Squeaking Noise When Wipers Move on the Windshield?

The wiper is a cleaning tool on a car that ensures the cleanliness of the windshield and maintains the driver's clear visibility. 1. Debris between the wiper and the windshield: When the car is stationary, debris such as leaves and dust may accumulate on the windshield. If the wiper is activated without cleaning these debris, it can cause squeaking noises and, in severe cases, even scratch the windshield. 2. Issues with the wiper blade: The wiper blade is made of rubber and will naturally age over time. Prolonged exposure to sunlight can cause the blade to harden and deteriorate. 3. Misalignment of the wiper: The wiper has a fixed position to properly cover the windshield. However, over time, the wiper may shift out of place. 4. Fault in the wiper linkage mechanism: The linkage mechanism of the wiper is complex, and malfunctions in components such as the motor or intermittent relay can cause the wiper to move too fast or too slow, leading to squeaking noises.

7

1

Share

What Can Be Used as a Substitute for Battery Fluid?

Battery fluid can be replaced with distilled water. Lead-acid batteries are chemical reaction devices composed of positive and negative plates, separators, and a solution containing sulfuric acid, used for storing and discharging electricity. In cases where the battery fluid is low, you can add battery replenishment fluid or distilled water. Tap water and purified water contain certain minerals and should not be used as substitutes for battery fluid. Here is some information about battery fluid: 1. Battery fluid, also known as electrolyte, is a dilute sulfuric acid made by mixing distilled water with sulfuric acid. It is used to react with the plates in the battery for charging and discharging. 2. Battery fluid is prepared by mixing specialized sulfuric acid and distilled water in a certain ratio, with a density generally ranging from 1.24 to 1.30 grams per cubic centimeter.

2

4

Share

What are the models of Mitsubishi Lancer?

Mitsubishi Lancer is a compact sedan. The first-generation Lancer was introduced in 1973, primarily designed to fill the gap between MINIca and Galant. The high-performance version of the Mitsubishi Lancer is the Evo, which is a compact sports sedan. Here are some relevant details: 1. Market Price and Positioning: The suggested retail price is around 70,000 yuan, making it suitable for general family use or as a vehicle for young people. 2. Configuration Parameters: This model is equipped with a 2.0-liter turbocharged engine, delivering a maximum power of 280 horsepower and a maximum torque of 355 Nm. The maximum power is achieved at 6,500 rpm, and the maximum torque is achieved at 3,500 rpm.

18

0

Share

How Many Liters of Transmission Oil Does the Vezel Require?

How to Turn Off the Auto Start-Stop Function in a Car?

Replacement Cycle of Antifreeze for Hyundai Elantra

What Are the Reasons for Low Idle Speed During Cold Start?

What Causes the Squeaking Noise When Wipers Move on the Windshield?

What Can Be Used as a Substitute for Battery Fluid?

What are the models of Mitsubishi Lancer?

How to Drive a Manual-Automatic Transmission Car Up a Steep Slope?

What does the AC on the car's air conditioner mean?

Is the Lynk & Co 02 an SUV?

What are the reasons why the air conditioner sometimes does not cool?