How many liters of transmission oil does the Toyota Reiz require?

Where is Geely Automobile Produced?

Geely Automobile is produced in Linhai, Ningbo, Luqiao in Zhejiang Province, and Shanghai. Here is some relevant information about Geely Automobile: 1. Logo Meaning: The new logo of Geely Automobile continues the design concept of six gemstones from the Brand 3.0 era, using the expanding universe as the design source, incorporating silver starlight, deep space gray, and earth blue, showcasing Geely Automobile's evolution from the blue sky and earth of the Brand 3.0 era to the pursuit of the vast universe. 2. Sub-brands: Geely Automobile Group currently owns the Geely Automobile brand, Lynk & Co brand, Geometry brand, Proton brand, and Lotus brand.

1

3

Share

What does the ABS light on the car dashboard mean?

The ABS light on your car indicates a malfunction in the Anti-lock Braking System. If the wheels lock up during emergency braking, the vehicle may skid uncontrollably, making it difficult for the driver to slow down or adjust the vehicle's trajectory, which poses a significant safety hazard. There are several conditions under which the ABS light may illuminate, each with different causes and solutions: Condition 1: ABS warning light stays on (most common). Cause 1: The ABS speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting its ability to detect the vehicle's speed signal. This prevents the ABS computer from determining the speed and wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections in the system wiring or poor contact in the ABS relay can lead to signal issues and system failure. Solution: Check all wiring connections and reattach any loose ones. Condition 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple electrical components are in use, the battery voltage may drop below 10.5V. As the engine speed increases and voltage rises, the ABS light turns off. This can also happen if the ABS system's power supply voltage is too low due to poor contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and examine the power supply (e.g., voltage relay or power contact issues). Condition 3: ABS warning light stays on after engine start until the engine is turned off. Cause: Poor grounding contact in the ABS hydraulic valve body, faulty wiring connections in the valve body, or a malfunctioning ABS computer. Solution: Loosen and retighten the grounding screws on the hydraulic valve body, clean contact surfaces if necessary, check for enlarged gaps in connectors, and replace the ABS or ABS/ASR computer if needed. Condition 4: ABS warning light illuminates during high-speed driving. Cause: The ABS computer detects a significant discrepancy between rear and front wheel speeds during high-speed driving, possibly due to incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, typically found on the label near the fuel tank cap. Condition 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch or poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, manually push the brake switch lever down fully, then release the brake pedal to reset its position. Replace the brake light switch if necessary.

13

1

Share

What is the cylinder pressure of the Volkswagen CSR engine?

Engine cylinder pressure is between 1100 and 1300kpa. The reasons for insufficient engine cylinder pressure are: Insufficient cylinder lubrication causing cylinder scoring, leading to excessive cylinder wall wear; Poor or damaged cylinder head gasket sealing, resulting in insufficient airtightness between the cylinder block and cylinder head; Excessive flatness of the two contact surfaces between the cylinder head and cylinder block, causing poor cylinder sealing; Intake and exhaust valves not closing tightly; Malfunction in the vehicle's cooling system leading to insufficient engine heat dissipation. The solutions for insufficient engine cylinder pressure are: Replace piston rings or cylinder liners; Replace the cylinder head gasket and tighten the screws to the specified torque; Check if the water passages are clear, pay attention to adding coolant, and promptly replace or eliminate any leaking components.

14

5

Share

What Causes a Sudden Increase in Fuel Consumption for an Audi at 60,000 Kilometers?

Excessive engine carbon buildup is a significant reason. Severe engine carbon deposits: Carbon deposits typically form on the fuel injectors, spark plugs, throttle valve, and combustion chamber. When carbon buildup reaches a certain level, it can cause difficulty in ignition. Use of low-quality fuel: Since low-quality fuel contains more impurities, it cannot burn completely, leading to most of the gasoline being expelled from the vehicle. Additionally, a white or reddish-brown layer forms on the surface of the oxygen sensor, causing misjudgment in measuring the oxygen content in the exhaust. This results in incorrect feedback data, ultimately affecting the proper control of the fuel injection ratio. Excessive vehicle load: Carrying too many unnecessary items in the vehicle can increase its weight. Some drivers prefer to fill the fuel tank to the brim, which also adds to the vehicle's weight. The heavier the load, the greater the pressure on the tires against the ground, leading to increased tire friction.

14

0

Share

Will running a red light in Xuzhou result in penalty points?

If there are cameras, the vehicle will be photographed. Whether it's running a red light while turning left or going straight, it is considered a violation of traffic laws. Article 44 of the Road Traffic Safety Law states that when motor vehicles pass through intersections, they should follow traffic signals, signs, road markings, or the directions of traffic police. When passing through intersections without traffic signals, signs, road markings, or traffic police directing, vehicles should slow down and yield to pedestrians and vehicles with the right of way. Here are some ways to avoid running a red light: First, observe the arrow signal, then the circular signal: Currently, there are two types of traffic signals: arrow signals and circular signals. When arrow signals are present, drivers should first check the arrow signal and then the circular signal to avoid running a red light. Note: When encountering a circular red light, right turns are allowed. However, if the right-turn arrow signal is red, right turns are prohibited, and violating this will be penalized as running a red light. Brake promptly: When the red light turns on, ensure the front of the vehicle does not cross the stop line. If the front wheels accidentally cross, and the rear wheels follow, the electronic camera will capture it, and it will be penalized as running a red light. If the front wheels have just crossed the stop line when the signal turns red, the vehicle must not proceed further and should wait for the green light. Check the countdown of the green light before proceeding: When the green light flashes, if there is a countdown, drivers can judge accordingly. If there is no countdown and the vehicle is close to the intersection at high speed, it may proceed to avoid running a red light due to untimely braking. If the speed is low and the vehicle is far from the intersection, it should brake immediately to avoid running a red light. Article 38 of the Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China states the following for motor vehicle and non-motor vehicle signals: When the green light is on, vehicles are allowed to proceed, but turning vehicles must not obstruct the passage of vehicles going straight or pedestrians. When the yellow light is on, vehicles that have already crossed the stop line may continue to proceed. When the red light is on, vehicles are prohibited from proceeding. At intersections without non-motor vehicle or pedestrian signals, non-motor vehicles and pedestrians should follow the motor vehicle signals. When the red light is on, right-turning vehicles may proceed if they do not obstruct the passage of other vehicles or pedestrians. Running a red light is not considered a violation under the following circumstances: Yielding to emergency vehicles: When yielding to ambulances, fire trucks, or other emergency vehicles, if the act is captured by surveillance cameras, manual review will not record the red light violation. Even if recorded, drivers can apply for reconsideration at the traffic police department. Extreme weather conditions: If visibility is extremely low and even electronic police cannot clearly see the traffic signals, the evidence of violation may be unclear, and no penalty will be imposed for mistakenly running a red light. Emergency situations: When transporting a critically ill patient to the hospital, running multiple red lights may occur. In such cases, the driver can provide hospital or patient documentation to the traffic police for verification. If confirmed, the violation records will be cleared. If possible, calling an ambulance is advisable to avoid accidents caused by running red lights. Traffic police directing: During peak hours, traffic police may temporarily direct traffic at major intersections. Drivers should follow the gestures of the traffic police. The traffic police department states that according to the Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China, when the yellow light flashes at an intersection, vehicles that have already crossed the stop line may continue to proceed. If the yellow light is already on and the driver still attempts to rush through, it will be considered running a red light if captured.

19

3

Share

Does the Neta V electric car have a rearview camera?

The Neta V electric car does not have a rearview camera. Reasons for a black screen in the rearview camera: First, you need to determine if it is caused by external factors. Get out of the car and check if the rearview camera is blocked by something. Second, there are many internal reasons, such as poor contact in the camera wiring, camera malfunction, display settings issues, etc. Among these, wiring problems are the main cause of a black screen in the rearview camera. This is because the rearview camera wiring runs from the trunk to the dashboard, which is quite long, and it is highly likely that poor contact occurs at some point in the wiring or connectors. How to fix a black screen in the rearview camera: First, if it is covered by fog or mud, simply wipe it clean with a damp cloth. Second, troubleshoot from simple to complex. Start by checking if it is a display settings issue. In the display settings, there is usually a camera switch control menu; just set the switch to the "ON" position. If the display screen does not respond at all, it may be a screen issue, and you will need to go to a 4S shop or auto repair shop for repair or replacement. Third, check the wiring connections to see if there are any loose or disconnected parts. If so, simply reconnect them properly. Fourth, if the rearview camera itself is faulty or the wiring is aged, replacing it with a new one should solve the problem.

11

0

Share

How many liters of transmission oil does the Toyota Reiz require?

Where is Geely Automobile Produced?

What does the ABS light on the car dashboard mean?

What is the cylinder pressure of the Volkswagen CSR engine?

What Causes a Sudden Increase in Fuel Consumption for an Audi at 60,000 Kilometers?

Will running a red light in Xuzhou result in penalty points?

Does the Neta V electric car have a rearview camera?

What does the Subject 3 driving test include?

How long after passing Subject 1 can you take the Subject 2 test?

Can ETC only be used for one vehicle?

Can You Wear a Hat for the Subject 1 Test?