How Many Liters of Transmission Fluid Does a Honda Civic Need for a Change?

1 Answers
VanCharles
07/28/25 5:12pm
The 10th-generation Honda Civic manual transmission requires approximately 4L of transmission fluid for a change, while the CVT transmission requires 8-12L. Transmission Fluid Replacement Interval: Generally, a car's transmission fluid should be replaced every two years or every 40,000 kilometers, though the exact interval may vary depending on the vehicle model. Failing to replace the transmission fluid in time can lead to fluid degradation, reduced vehicle acceleration, and accelerated transmission wear. Methods for Replacing Transmission Fluid: The flush machine method uses specialized equipment to dynamically replace automatic transmission fluid under pressure, achieving a replacement rate of over 80%. This process is straightforward but requires specific equipment. In contrast, traditional gravity drainage only removes about half of the old fluid, whereas the flush machine enables a more thorough replacement, which can help extend the transmission fluid maintenance interval.
Was this review help?
20
5
Share
More Forum Discussions

How to Replace an Automotive Ignition Lock Cylinder?

There are a total of 5 cross-head screws below; simply unscrew them. One thing to note is that the cover consists of upper and lower parts. These are hex socket screws, so a hex screwdriver is required. The screw holes can be seen above the turn signal and wiper levers, with one on each side. There is a clip on the connector; be sure to release it first. The lock cylinder cannot be unscrewed or pulled out directly—there is a mechanism inside. Turn the key to the "B" position and then pull it out.
19
3
Share

What is the real fuel consumption of the Jeep Cherokee 2.0?

2.0L models have a fuel consumption of 9.7 liters per 100 kilometers, while 2.0T models consume 10.9 liters per 100 kilometers. The following is a related introduction to the Cherokee 2.0: 1. 2.0-liter naturally aspirated engine: The 2.0-liter naturally aspirated engine delivers 148 horsepower and a maximum torque of 190 Nm. This engine reaches its maximum power at 6250 rpm and its maximum torque at 4600 rpm. It features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. 2. Low-power version 2.0-liter turbocharged engine: The low-power version 2.0-liter turbocharged engine produces 234 horsepower and a maximum torque of 350 Nm. This engine achieves its maximum power at 5000 rpm and its maximum torque between 2500 and 4500 rpm. It is equipped with direct fuel injection technology and uses an aluminum alloy cylinder head and block. 3. High-power version 2.0-liter turbocharged engine: The high-power version 2.0-liter turbocharged engine generates 265 horsepower and a maximum torque of 400 Nm. This engine reaches its maximum power at 5200 rpm and its maximum torque between 3000 and 4250 rpm. It features direct fuel injection technology and uses an aluminum alloy cylinder head and block.
6
2
Share

Why is there water under the co-driver's foot mat in Jetta?

There may be water under the chassis if there is water under the co-driver's foot mat in Jetta. Exterior Design: The front headlights are matched with the currently popular black bottom lining frame, the exquisite and atmospheric chrome grille, and the design of the front and rear bumpers is integrated with the simple and tough body of Jetta, making the combination of the front end, fenders and side body more perfect. In terms of interior design, avant-garde, fashionable and innovative elements are integrated, forming a unified interior style with other configurations in the car, which is comfortable and beautiful. In terms of model size, the interior space is more spacious, the ride is more comfortable, and it better meets the needs of Chinese consumers for a family and business dual-purpose car. 1.4L EA211 Engine: The new Jetta 1.4L model is equipped with a 1.4L EA211 engine, which reaches the maximum output power of 66kW at 5500 rpm and the maximum output torque of 132N.m at 3800 rpm. The small-displacement engine not only brings users lower car use costs but also achieves energy saving and environmental protection.
2
2
Share

What is the minimum ground clearance of the Tang DM?

The minimum ground clearance of the Tang DM is 180 millimeters. The minimum ground clearance of the Tang DM refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which is used to indicate the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. A higher ground clearance of the Tang DM improves its off-road capability, but if the ground clearance is too high, the stability at high speeds may decrease. The Tang DM is a mid-size SUV under BYD. The dimensions of the Tang DM are 4870 mm in length, 1940 mm in width, and 1720 mm in height, with a wheelbase of 2820 mm. Generally, the ground clearance of sedans ranges between 110 mm and 150 mm, while SUVs have a ground clearance between 200 mm and 250 mm. However, the ground clearance of the Tang DM is not static; it also depends on the load condition. Therefore, changes in ground clearance should be considered based on the Tang DM's load variations. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For urban areas with well-paved roads, a vehicle with lower ground clearance can enhance stability and comfort. For long-distance travel or driving in areas with poor road conditions, a vehicle with higher ground clearance is preferable to avoid scraping or damaging the chassis.
11
0
Share

What is the normal range for winter tire pressure?

Winter tire pressure typically ranges from 2.4 to 2.6 bar. Different vehicle models have varying weights and tire specifications, which means the standard tire pressure may differ. You can find the specific tire pressure for your vehicle in the owner's manual. Excessive tire pressure can cause steering wheel vibration and deviation, reducing driving comfort, while insufficient tire pressure increases movement in various parts of the tire, leading to abnormal heat generation due to excessive rolling. Tires are circular elastic rubber products mounted on vehicles or machinery, usually installed on metal rims. They support the vehicle body, absorb external shocks, maintain contact with the road surface, and ensure driving performance.
10
3
Share

How to Deal with Oxidized Car Trim Strips?

Methods to handle oxidized car trim strips: 1. Use toothpaste: Toothpaste contains antioxidants and cleaning abrasive particles. Simply dip a wet towel in toothpaste and polish the strips; 2. Use toilet cleaner: Toilet cleaner contains dilute hydrochloric acid, which can dissolve oxides. Dip a towel in the cleaner and wipe the strips, then use a clean wet towel to remove any residual acid. Car trim strips are decorative strips installed along the edges of car windows, primarily serving an aesthetic function. Window trim strips typically feature a chrome-plated design, with high-quality ones made of stainless steel for a shiny silver appearance.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.