Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

How many liters of engine oil should be added to a BMW M4?

1 Answers

Kaden

07/30/25 5:38am

BMW M4 requires the addition of: 3-3.5 liters of engine oil. The steps for adding engine oil are introduced as follows: 1. Clean the oil dipstick: After the car is parked and turned off for about ten minutes, pull out the oil dipstick and wipe the oil traces on the dipstick with a cloth. 2. Observe the situation: Reinsert the oil dipstick into the dipstick tube, then pull it out again to check the oil traces on the dipstick. Under normal circumstances, the oil traces should be between the upper and lower marks on the dipstick, slightly above the middle line. If the oil traces are below the lower mark, it indicates insufficient oil and you should add oil immediately. While adding oil, continuously pull out the oil dipstick to observe the situation of the added oil. 4. Avoid mixing: When topping up engine oil, pay attention to the consistency between the added oil and the oil in the engine, avoiding mixing different brands or types of engine oil.

Was this review help?

11

3

Share

More Forum Discussions

What are the solutions for a trunk that won't open?

The solutions for a trunk that won't open are: 1. Remove the interior trim panel of the trunk; 2. Remove the screws and clips at the back and middle; 3. Secure and install the switch core. The reasons for a trunk not opening are: 1. Issues with the linkage rod or lock cylinder; 2. The trunk is frozen or stuck; 3. The trunk is rusted or corroded. The replacement method for the trunk is: 1. Remove the hatch; 2. Support the trunk with a wooden board; 3. Pry open the hydraulic rod at the bottom of the hatch; 4. Install the hatch support; 5. Push the hydraulic rod of the trunk lid into the slot by hand. The function of the trunk is to absorb and buffer part of the collision energy in a rear-end collision and to increase storage space.

What does the B gear in a vehicle mean?

B gear stands for Brake. It is the abbreviation of the English word 'brake', so the B gear can be understood as the braking gear. Detailed explanations about the B gear are as follows: 1. This braking is not directly applied to the brake pedal but uses the engine to restrain the vehicle. 2. It is usually used on some continuous long downhill sections. If you keep pressing the brake and descend in D gear, almost all the braking pressure is borne by the brake, and prolonged use can cause the brake pads to overheat and lead to brake failure. 3. When shifted into B gear, the transmission is limited to low gears (1-2) by the lock mechanism, and the engine's restraining effect is used to allow the vehicle to brake at low gear, thereby relieving most of the pressure on the brake. 4. The function of the B gear is similar to that of the L gear. The B gear can also be used when starting on a steep slope, playing the role of low speed and high torque.

What Brand of Engine is Cummins?

Cummins, known as Kang Ming Si in Chinese, is introduced in detail below: 1. It is the world's largest independent engine manufacturer, with a product line that includes diesel and alternative fuel engines, key engine components (fuel systems, control systems, intake processing, filtration systems, and exhaust treatment systems), as well as power generation systems. 2. Cummins was founded in February 1919 and is headquartered in Columbus, Indiana, USA. The company serves its customers through over 500 distribution facilities and more than 5,200 dealer locations in more than 190 countries and regions worldwide. 3. Cummins is a Fortune 500 company in the United States and was named one of the 'World's Most Admired Companies' by Fortune for two consecutive years (2008, 2009), being the only diesel engine company on the list.

Should You Engage the Parking Brake or Shift Gears First in an Automatic Transmission?

In an automatic transmission, you should engage the parking brake first before shifting gears. The correct procedure for using an automatic transmission is: 1. After getting into the car, shift the gear lever into the starting gear; 2. Sound the horn, turn on the turn signal, and simultaneously observe the front, sides, and rearview mirrors to check for any pedestrians or vehicles approaching from behind; 3. Check for any obstacles that might hinder starting, paying special attention to safety; 4. Firmly hold the steering wheel, activate the left turn signal, and release the parking brake lever. The reason for shifting gears before releasing the parking brake when starting is to prevent the vehicle from rolling. If you release the parking brake first, the vehicle will be in neutral for a period before shifting into gear. Moreover, when starting, you may not know if the ground is level. If it's inclined, the car in neutral could roll backward, potentially causing an accident.

Why is the reversing camera not displaying on the Mercedes-Benz S320?

The reasons why the reversing camera does not display on the Mercedes-Benz S320 are: 1. The gear is not in reverse; 2. The vehicle battery is dead; 3. The vehicle system is malfunctioning; 4. The reversing camera or wiring is damaged. Taking the 2019 Mercedes-Benz S320 as an example, its body structure is a 4-door, 5-seater sedan, with body dimensions of: length 5259mm, width 1899mm, height 1497mm, wheelbase 3165mm, fuel tank capacity 80l, and trunk capacity 510l. The 2019 Mercedes-Benz S320 is equipped with double-wishbone independent suspension both front and rear, and is powered by a 2.0l turbocharged engine, with a maximum horsepower of 299ps, maximum power of 220kw, and maximum torque of 400nm.

How to Tell if a Car is Pulling to One Side?

Methods to determine if a car is pulling to one side are as follows: 1. While driving, if the steering wheel is held steady, the car should generally move straight in most cases. If it deviates to the left or right, this is referred to as pulling to one side. 2. Ensure all four tires are evenly inflated. Drive on a straight, flat road with your hands lightly holding the steering wheel (as if controlling it but without actual contact, to quickly regain control if needed), and conduct the test under no crosswind conditions. 1. If the car's trajectory shifts to the left after driving a certain distance, it is pulling to the left; if it shifts to the right, it is pulling to the right. 2. Remember that the deviation must be significant to be considered as pulling to one side. Minor deviations within a kilometer do not count as pulling.

Trending Ranking

What brand does Exeed belong to?

What are the types of synchronizers?

How to Disassemble a Car Key Fob?

What's the difference between Pirelli P7 and P7KS?

Is it necessary to add break-in oil for a new car?

What is the car model with two inverted V logos?

What is the correct way to use car air conditioning in summer?

Solution for P0342 Trouble Code?

How to Identify the Production Date of Car Lights?

What are the differences between ATS and XTS?

More Forum Discussions

What is the method for replacing piston rings?

What is the method for checking the engine oil level in a car?

What is the method for identifying the national emission standard of a vehicle?

How to Check the Vehicle Production Date via VIN?

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.