How many liters of engine oil does the BMW X1 require?

2 Answers
AustinMarie
07/25/25 11:15am
The BMW X1 requires 4.5 liters of engine oil. The original factory oil brand for the BMW X1 is Shell. If you wish to change the oil during later maintenance, you can choose brands such as Shell, Mobil, Castrol, or Total. The official BMW X1 manual recommends using engine oil with the specification 5W-30. Any oil model that meets this specification parameter can be used. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts for the car. The latter number represents the kinematic viscosity of the oil at 100°C. The higher the value, the better it maintains viscosity under high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the engine oil in a BMW X1 is as follows: Wait for the engine temperature to drop, allowing the oil to flow back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine and let it run for 30 seconds to allow the oil in the main oil passage to drain out. Use a special wrench to remove the oil filter. Apply some oil to the oil seal of the new oil filter and tighten it clockwise by hand. Add the new engine oil through the oil filler cap on the engine valve cover. Generally, fill up to three-quarters of a standard oil container. Start the engine and let it run for 5 minutes, then check for any leaks around the oil drain plug and oil filter. If there are leaks, perform necessary repairs. After stopping the engine, pull out the oil dipstick to check if the engine oil level is within the standard range.
Was this review help?
5
3
Share
DiAliyah
08/11/25 7:58pm
I've been driving a BMW X1 for a while now. When changing the engine oil, it usually takes about 5 liters, depending on the engine model. For example, a 1.5T engine requires approximately 4.8 to 5.2 liters. In daily use, it's best to check the manual or use the dipstick to avoid overfilling, which can lead to oil leaks or engine overheating. I've made the mistake of not measuring carefully before and ended up adding too much oil once, resulting in unstable oil pressure, jerky starts, and increased fuel consumption. The repair cost me several hundred dollars. Regular maintenance is crucial. I recommend checking the oil level every 5,000 kilometers to ensure smooth engine performance and prolong the car's lifespan. If you drive frequently in the city, you should check even more often. Changing the oil yourself is manageable, but beginners should visit a professional shop to avoid mistakes. Choosing the right oil specification is also key—BMW recommends synthetic oil to protect engine components. In short, make it a habit and don’t slack off.
Was this review help?
20
3
Share
Expand All
More Forum Discussions

Should You Press the AC Button When Using the Car Air Conditioner?

When using the air conditioner in summer, you must press the AC button first. However, it's different when using the heater. The heater utilizes the car's internal heat circulation system, making use of waste heat, so there's no need to press the AC button. Therefore, remember, when turning on the heater in winter, you only need to adjust the air conditioning button without pressing the AC button. Here is some additional information: 1. The heater relies on the heat dissipation from the engine. There is a small fan in the engine compartment that blows the heat collected by the cooling system into the car. 2. If you don't turn on the heater, this heat will be discharged outside the car. Turning on the heater without pressing the AC button is simply making use of waste heat and will not increase any fuel consumption.
15
1
Share

Where is the VIN number on a smart car?

smart car's VIN number is located at the junction angle between the rear trunk insulation pad and the cover panel. The VIN refers to the Vehicle Identification Number. Taking the smart fortwo 2019 model as an example, its body dimensions are: length 2695mm, width 1663mm, height 1544mm, wheelbase 1873mm, fuel tank capacity 33L, and the body structure is a 3-door 2-seat hatchback. The smart fortwo 2019 model is equipped with a 0.9T turbocharged engine, with a maximum power of 66kW and a maximum torque of 135Nm, paired with a 6-speed dual-clutch transmission. It adopts a front suspension type of MacPherson independent suspension.
15
0
Share

How to set up automatic door locking for Honda CR-V?

To set up automatic door locking for Honda CR-V, follow these steps: 1. Press the brake pedal of the Honda CR-V; 2. Shift the gear lever to N position; 3. Release the brake pedal; 4. Press the one-touch start button twice consecutively; 5. Close all doors; 6. Press and hold the lock button on the driver's side door for more than 10 seconds to complete the operation. The Honda CR-V is an SUV model produced by Dongfeng Honda Automobile Co., Ltd. Its body dimensions are: length 4550 mm, width 1820 mm, height 1685 mm, wheelbase 2620 mm, curb weight 1564 kg, and fuel tank capacity 53 liters.
20
1
Share

Is the Volkswagen Touareg domestically produced?

Volkswagen Touareg is not domestically produced and is mainly introduced into the Chinese automotive market through imports. Taking the Volkswagen Touareg 2021 model as an example, its body dimensions are: length 4878mm, width 1984mm, height 1717mm, wheelbase 2899mm, fuel tank capacity 90l, and the body structure is a 5-door 5-seat SUV. The Volkswagen Touareg 2021 model is equipped with a 2.0T turbocharged engine, with a maximum power of 180kW and a maximum torque of 370Nm, paired with an 8-speed automatic transmission. It adopts multi-link independent suspension for both front and rear suspension types.
14
0
Share

What Causes the Transmission Oil Leak in the Cavalier?

The reasons for transmission oil leakage in the Cavalier are: 1. Aging, deformation, or incorrect installation direction of the oil seal, or spring detachment; 2. Pipeline damage; 3. Loose screws on the transmission cover; 4. Damage to the joint surface of the transmission case; 5. Excessive clearance at the shaft ends; 6. Wear of the oil seal or flange, or gear oil exceeding the specified standard; 7. Improper use of lubricating oil. The Cavalier's body dimensions are: length 4474mm, width 1730mm, height 1471mm, wheelbase 2600mm, fuel tank capacity 36L, trunk capacity 469L. It is equipped with a 1.0T turbocharged engine, with a maximum power of 92kW and a maximum torque of 180Nm.
3
3
Share

Why is there no fee deduction displayed after passing through the highway with ETC?

The reason why there is no fee deduction displayed after passing through the highway with ETC is: the deduction is not in real-time, and most of the time it is delayed for a few days before being processed. ETC works through dedicated short-range communication between the onboard electronic tag installed on the vehicle's windshield and the microwave antenna in the ETC lane at the toll station. It uses computer networking technology to perform backend settlement processing with the bank, achieving the purpose of vehicles passing through highway or bridge toll stations without stopping to pay the fees. The reasons why ETC may not be detected include: 1. The electronic tag is not inserted correctly; 2. Unauthorized removal of the onboard electronic tag will render it unusable; 3. The vehicle's windshield has a metal explosion-proof film; 4. OBU transfer or replacement requires visiting a service center.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.