How many liters of engine oil does the Arrizo 5 use?

How to adjust the handbrake of Haima M5?

Use a jack to lift the rear of the car so that the two rear wheels can rotate. Adjust the car's gear. If it's an automatic transmission, shift to P gear; if it's a manual transmission, shift to 1st or 2nd gear. Adjust the handbrake to an appropriate tightness. If it's too tight, the screws may not turn; if it's too loose, parts inside the handbrake may block the view of the screws. After adjustment, fully release the handbrake and check if the rear wheels can rotate. Both rear wheels should be checked to prevent wheel lock.

18

0

Share

What to Do When There Are Too Many Cars to Overtake in Subject 3?

Turn on the left turn signal, observe the left rearview mirror, and note that during the exam, there must be an obvious head-turning action. After the left turn signal has been on for three seconds, observe the left rearview mirror again to confirm there is no traffic behind, then accelerate and change lanes. Once the lane change is completed, immediately turn on the right turn signal and observe the right rearview mirror. As above, there must be an obvious head-turning action. After the right turn signal has been on for three seconds, observe the right rearview mirror again to confirm there is no traffic, then change lanes back to your original lane. This completes the overtaking maneuver.

13

2

Share

How to Register an Out-of-Town Used Car with Local License Plates?

First, confirm whether the local vehicle management office accepts the model you intend to purchase. For example, some cities do not accept vehicles that are too old or carburetor-equipped vehicles. When purchasing the used car at the buying location, it is usually required that the seller handles the file transfer. During the file transfer process, you must provide the identity proof of the new owner who will register the vehicle. After returning, submit the files to the local vehicle management office for review. Once the review is passed, you can begin the registration process. After obtaining the new license plates, use the new vehicle registration certificate, transaction invoice, and relevant transfer documents to complete the transfer of the purchase tax at the purchase tax management office.

11

4

Share

How to Deal with Small Dents on Car Paint?

First, clean the dented area thoroughly, then load the special glue into the glue gun and plug it in to preheat for about 7 minutes. Next, select an appropriate backing plate, noting that larger dents require larger backing plates, as the larger the backing plate, the greater the traction force. Then, evenly apply the melted glue from the glue gun onto the backing plate, quickly press it onto the dented area, and hold it gently until the special glue sets firmly before releasing. Align the hole in the middle of the traction bridge with the backing plate, place the nut over the screw rod of the backing plate, and tighten it. Continue turning the nut until the dent is pulled out and leveled. After the repair is complete, remove the tools, spray alcohol on any residual glue on the car body, and finally clean it off with a scraper.

5

0

Share

What are the causes of steering system failure in BYD Qin?

Steering system failures are caused by issues such as steering gear malfunction and power steering pump failure. Specific faults: Oil leakage from the steering gear at the upper cover, side cover, and the connection point of the steering shaft arm, abnormal noises during steering, and oil leakage at the rear cover of the power steering pump can all lead to steering system failure. Solutions: The upper cover, side cover, and steering shaft are equipped with sealing rings. Replacing the oil seals and sealing rings can resolve steering gear issues. Oil leakage at the rear cover of the power steering pump is typically due to damaged sealing rings, which can be fixed by replacing the rear cover sealing ring. Abnormal noises during steering are often caused by damaged thrust bearings in the steering column. During inspection, turning the steering wheel left and right to locate the source of the noise can help identify the issue for disassembly and repair.

11

5

Share

What is the purpose of polishing?

The following are the functions of automotive polishing: 1. Used to reduce the surface roughness of the car, obtaining a bright and smooth surface. 2. Removes issues affecting the paint appearance such as the oxidation layer on the paint surface, shallow scratches, and loss of gloss caused by oxidation. Below are the methods for polishing different automotive issues: 1. Defect removal: Spray a small amount of water on the paint surface, use P1500 pyramid sandpaper with a dry grinder to sand the entire surface once in all directions (up, down, left, right) until the paint surface becomes matte; after sanding, use a rubber squeegee to scrape off the white foam on the surface, observe the paint surface to identify prominent defects, then spray a small amount of water on the sanding disc to remove the defects. 2. Overly fine paint surface: Use a dry grinder with P3000 pyramid sanding disc and a dry sanding soft pad to finely sand the overly fine paint surface, spray a certain amount of water on the sanding disc and paint surface, and sand the entire paint surface twice in each direction (up, down, left, right) at a faster speed. After sanding, use a rubber squeegee to scrape off the surface water and white foam. Quality standard: The paint surface should be free of defects such as oxidation layers and scratches. 3. Coarse wax polishing: Further removes surface sanding marks after sandpaper grinding, restoring the paint surface's smoothness and initial gloss. Apply wax evenly on a certain area of the paint surface, with the polisher speed controlled between 1200-2000 RPM. Initially, apply medium to high pressure to the polishing pad to polish the paint surface at a uniform speed. Observe the paint surface, and once the sanding marks are significantly removed, reduce the pressure to remove the wax marks, restoring some gloss to the paint surface. After polishing, use a microfiber cloth to clean off any residual coarse wax and dust from the paint surface.

9

3

Share

How many liters of engine oil does the Arrizo 5 use?

How to adjust the handbrake of Haima M5?

What to Do When There Are Too Many Cars to Overtake in Subject 3?

How to Register an Out-of-Town Used Car with Local License Plates?

How to Deal with Small Dents on Car Paint?

What are the causes of steering system failure in BYD Qin?

What is the purpose of polishing?

What to Do When the Seat Belt Height Adjustment is Damaged?

How to deal with small dots after car painting?

What is the size of the Prado wiper blades?

How Many Times Can a Driving Test Appointment Be Canceled?