How many kilowatt-hours does it take to fully charge the Wuling Hongguang?

2 Answers
LeAmelia
07/24/25 1:02am
It takes 10 kilowatt-hours to fully charge the Wuling Hongguang. Here are the extended details: Battery Type: The model uses lithium-ion batteries with battery capacities of 9.3KWH and 13.9KWH. The battery pack warranty is eight years or 120,000 kilometers. The slow charging time is 6.5 hours and 9 hours. The vehicle is positioned as a micro-level car. Body Parameters: The vehicle dimensions are 2917 mm in length, 1493 mm in width, and 1621 mm in height. The wheelbase is 1940 mm. The front track is 1290 mm, and the rear track is 1290 mm. The minimum ground clearance is 125 mm. The model is a three-door, four-seat hatchback equipped with a permanent magnet synchronous motor, featuring a single rear-mounted motor configuration.
Was this review help?
4
4
Share
VanMadeline
08/10/25 8:45pm
As a daily driver of the Wuling Hongguang MINI EV, a full charge consumes about 13.8 kWh, which is more than enough for my weekly urban commute. On average, each charging session costs less than 10 yuan in electricity, making it much more economical than driving a gasoline car. I usually charge it overnight using a household socket, taking about 8 hours to go from empty to full. This car is compact and agile, making parking a breeze, and it's perfect for navigating busy urban areas. If you also drive the same model, remember to regularly check the safety of the charging socket to avoid overheating and fire. It's best to charge in a garage or a safe location and avoid operating in rainy conditions. With proper care, the battery can last over 5 years, and maintenance is simple and low-cost, making it truly hassle-free.
Was this review help?
18
5
Share
Expand All
More Forum Discussions

What is the displacement of 300cc?

300cc equals 0.3 liters of displacement, where "300CC" refers to the exhaust volume of a motorcycle engine's combustion chamber. CC is a unit of volume for cylinder displacement, with 1CC equivalent to 1ml. According to China's relevant standards, different displacements correspond to the following vehicle types: 30CC and below are defined as fuel-powered mopeds. 30-50CC are defined as light motorcycles. Above 50CC is defined as a standard motorcycle. Within standard motorcycles, they can be further categorized as: entry-level motorcycles defined as 250-400CC. Mid-range motorcycles are defined as 500-750CC. Heavy motorcycles (liter-class) are defined as above 1000CC. Motorcycle licenses are divided into categories D, E, and F. Motorcycles come in two-wheeled and three-wheeled varieties. Apart from directly applying for a beginner's two-wheeled or three-wheeled motorcycle license, one can also apply for an upgrade to a two-wheeled or three-wheeled motorcycle license. Applicants can use their resident ID card to apply for a motorcycle driver's license anywhere nationwide, take the exam, and upon passing, receive their motorcycle driver's license. For daily maintenance of a motorcycle's engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, choose SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions. For diesel engines, select CB--CD grade diesel engine oil based on mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine issues. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. As oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may burst the filter element or open the safety valve, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication area, accelerating engine wear, and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. In small amounts, it remains suspended in the oil; in large amounts, it precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
7
1
Share

What Causes a Car to Suddenly Stall?

Reasons for a car suddenly stalling: 1. Electrical circuit failure: This could be due to low-voltage power interruption while driving. In this case, you should primarily check the ignition and starter switches, as well as the fuse box. 2. Electrical component failure: Usually caused by faults in the ignition coil, capacitor, or electronic ignition module. 3. Fuel system failure: Damage to the fuel pump, fuel line rupture, clogged carburetor fuel inlet, or an empty fuel tank. However, in such cases, the car can still be restarted, though with difficulty. 4. Sensor failure: Faults in the throttle position sensor, air flow sensor, intake pressure sensor, crankshaft position sensor, or camshaft position sensor, among others. If any sensor fails, it can also lead to stalling.
3
5
Share

What are the reasons why a car suddenly cannot start?

Reasons why a car suddenly cannot start: 1. Dead battery: Sometimes you may find that the car cannot start normally in the morning, which is likely because the trunk was not completely closed, causing the trunk light to stay on and drain the battery; 2. Spark plug failure: Spark plugs themselves are prone to damage, and a short circuit in the high-voltage line can prevent the spark plug from igniting. Another reason is that poor-quality spark plugs can also cause the car to fail to start normally; 3. Starting circuit malfunction: When starting, there is only a slight click sound and no further response, which is caused by a stuck starting relay. To identify the cause of the fault, first check the battery to determine whether the engine's failure to start is due to insufficient battery power. To inspect the starting system, first examine the circuits in the engine starting system. Generally, the starting system's circuits include the battery, the starter motor, and the cables connecting these components.
11
1
Share

What Causes Excessive Consumption of Car Antifreeze?

Reasons for excessive consumption of car antifreeze: 1. Cooling system leakage: Pipes or drain plugs in the cooling system may leak. These parts are relatively easy to detect. Once the leaking part is found, simply tighten or reinstall the corresponding component. 2. Damaged radiator cap: The radiator cap contains an air valve and a steam valve. If the radiator cap malfunctions, causing the steam valve to open at too low a pressure or remain constantly open, it can lead to significant loss of antifreeze. In this case, the radiator cap needs to be replaced. 3. Antifreeze not meeting usage standards: Car engines operate at high temperatures. To prevent antifreeze from boiling, its boiling point is generally above 108 degrees Celsius. Inferior antifreeze that doesn't meet the standard will boil and evaporate. It is necessary to use genuine antifreeze. 4. Engine overheating: If the engine frequently overheats, the antifreeze will often boil and vaporize in large quantities, escaping through the radiator cap's steam valve, resulting in antifreeze loss. In this situation, it is necessary to visit a repair shop to check the cause of engine overheating.
9
2
Share

Can antifreeze of the same color be mixed?

Whether antifreeze of the same color can be mixed depends on the situation: 1. If the color is the same and the main components are almost identical, they can be mixed; 2. If the color is the same but the main components differ significantly, they should not be mixed, as this could cause a chemical reaction. The main components of antifreeze are ethylene glycol, propylene glycol, and diethylene glycol. Ethylene glycol is generally green, propylene glycol is red with a hint of orange, and diethylene glycol is blue. The reasons for antifreeze having different colors are: 1. To distinguish between different ratios of antifreeze—both water and antifreeze agents are colorless, making it impossible to differentiate different ratios by eye, so different dyes are added for distinction; 2. To clearly identify leaks in the antifreeze and help easily locate the leak point; 3. To easily monitor the consumption of antifreeze in the radiator and replenish it in time; 4. To prevent accidental ingestion and make it easy to distinguish from water.
1
1
Share

What is the difference between manual transmission and automatic transmission?

Differences between manual transmission and automatic transmission: 1. Gear shifting methods differ: Manual transmission vehicles require the use of a clutch to shift gears for acceleration or deceleration; automatic transmission vehicles rely on engine speed to automatically increase vehicle speed and shift gears. 2. Fuel consumption varies: Manual transmission vehicles only need to be placed in a high gear and the throttle held to maintain speed; automatic transmission vehicles require a larger throttle to increase engine speed in order to boost vehicle speed. Common automatic transmissions include AT transmissions, dual-clutch transmissions, and CVT transmissions. AT transmissions are technologically mature and widely used, offering relatively smooth gear shifting.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.