···
Log in / Register

How many kilometers should the brake pads of Volkswagen Lavida be replaced?

4 Answers
LaJonathan
08/30/25 2:53am
Volkswagen Lavida brake pads are generally replaced every 60,000 kilometers. The following are the steps to replace the brake pads of Volkswagen Lavida: 1. First, remove the wheel and reset the brake caliper. It is best to use a special tool, or a screwdriver if not available. 2. Then, remove the caliper fixing bolts, take off the old brake pads, install the new brake pads, install and tighten the caliper fixing bolts, and reinstall the wheel. 3. After all the brake pads are replaced, start the vehicle and press the brake pedal several times until the brake pedal has a certain resistance. 4. Finally, check whether the brake fluid level is within the standard scale. If the level is lower than the standard, it needs to be added. The new brake pads will achieve the best effect after 300-500 kilometers of use.
Was this review help?
16
5
Share
DiHeidi
09/11/25 7:02am
I've been driving my Volkswagen Lavida for just over three years, and replacing brake pads isn't just about mileage. Generally, it's recommended to check them every 40,000 to 60,000 kilometers, but it really depends on your driving habits. For example, I often drive in the city with lots of traffic lights, so I brake frequently, leading to faster wear. My first set of brake pads was replaced at 45,000 kilometers. If you drive mostly on highways, they can easily last over 60,000 kilometers. The key is to pay attention to unusual noises or longer braking distances—don't wait until the pads are worn down to the metal, as that's very dangerous. During regular maintenance, have the technician check the thickness—it's simple and gives peace of mind. The money-saving approach is to inspect more and replace less, but delaying too long risks damaging other parts, which would cost much more. In short, my personal advice is: check early to avoid regret later, safety first.
Was this review help?
20
0
Share
Expand All
ReaganRose
10/25/25 7:53am
Brake pad replacement shouldn't solely rely on mileage. With over 20 years of driving experience and having owned two Volkswagen Lavidas, I can tell you their lifespan varies greatly by driving habits. While the standard recommendation is replacement between 40,000 to 70,000 km, here's my practice: check every 40,000 km for city driving with frequent traffic jams, while highway/long-distance driving can extend to 60,000+ km. From a safety perspective, the braking system is life-critical - excessive wear leads to reduced braking power and significantly higher accident risks. I recommend adding brake inspections during routine maintenance - a small cost that prevents major troubles. Don't wait for warning lights; metallic scraping sounds are already warning signs. Ultimately, timely maintenance is fundamental to road safety - never skimp on this crucial effort.
Was this review help?
15
3
Share
Expand All
DiBella
12/08/25 8:17am
Having worked on cars myself for years, I change the brake pads on my Lavida based on wear, not mileage. The manufacturer's guide suggests inspection and replacement at 40,000 to 60,000 km, but that's unreliable because driving habits have a huge impact. I use calipers to measure thickness: new pads are 10mm, and I replace them immediately when they're down to 3mm. Stop-and-go city driving wears them out faster, sometimes needing replacement at just 30,000 km; highway driving with less braking can extend their life beyond 70,000 km. I recommend car owners learn simple self-checks, like lifting the wheel to inspect—it saves money and ensures safety. Don’t rely on dealership reminders; be proactive. In short, mileage is just a reference—actual observation is what matters.
Was this review help?
4
3
Share
Expand All
More Forum Discussions

What does it mean when a bulb with an exclamation mark appears on the dashboard?

Yellow bulb with an exclamation mark is the light fault indicator, indicating that there is a fault with the vehicle's lights. Solution: Go to a 4S shop for inspection and repair as soon as possible, or you can check it yourself. Focus on checking commonly used bulbs such as turn signals, fog lights, and interior lighting to identify the problem. The exclamation mark is a common fault indicator in cars. In addition to the yellow bulb with an exclamation mark, there are four other forms of exclamation marks: an exclamation mark inside a triangle, an exclamation mark inside a yellow gear, an exclamation mark in the middle of a bracket and circle, and an exclamation mark in the middle of a bracket with a line below. Here is a detailed analysis: General fault: An exclamation mark inside a triangle. If this symbol lights up, it indicates a fault with the vehicle's general performance, components, or functions. Common issues include parking sensor failure, fuel cut-off system intervention or failure, external light failure, and engine oil pressure sensor failure. It is necessary to go to a 4S shop for inspection to identify the source of the fault. Automatic transmission fault: An exclamation mark inside a yellow gear. This is the automatic transmission fault warning light, indicating a fault with the transmission or that the transmission lubricant is below the normal range. The transmission oil should be replaced promptly. Brake system fault: An exclamation mark in the middle of a bracket and circle. This represents a warning for the brake system, mainly indicating a brake system failure or low brake fluid level. The brake system should be inspected immediately to avoid accidents. Tire pressure abnormality: An exclamation mark in the middle of a bracket with a line below. This represents the tire pressure monitoring warning light, which lights up when the tire pressure is too low. Check the tire pressure and restore it to the normal range.
14
3
Share

What is the battery model for the Langdong car key?

The battery model for the Langdong car key is CR2032. The Langdong is a global model of Hyundai that was first launched overseas. Its exterior features the typical family design, with less sharp lines but more fullness, making it look more harmonious and moderate. The short rear end easily gives a sense of fullness and roundness, and the front grille is specially treated with full chrome plating to make it look more stylish. In terms of power, the Langdong is equipped with a 1.6L engine and a 1.8L engine. The 1.6L engine has a maximum power of 127ps and a maximum torque of 155nm, while the 1.8L engine has a maximum power of 145ps and a maximum torque of 175nm. In terms of body dimensions, the Langdong measures 4570mm in length, 1775mm in width, and 1445mm in height.
1
4
Share

How to Set the Rearview Mirror to Tilt Down When Reversing?

Method to set the rearview mirror to tilt down when reversing: 1. Power on the car but do not start it, set the memory seats to positions 1, 2, or 3, select the seat position, choose the side of the rearview mirror to be set, and press the rearview mirror adjustment selection button; 2. Step on the brake and shift to R gear, at this time the selected rearview mirror will automatically lower to the factory preset position, press the 4-way adjustment button to adjust to the desired position; 3. Press and hold the seat memory button for about 2 seconds, select the memory position, step on the brake and shift to P gear, then press the rearview mirror adjustment selection button. The rearview mirror is a tool that allows the driver to directly obtain external information about the rear, side, and lower parts of the car while seated in the driver's seat. For the convenience of the driver's operation, to prevent traffic safety accidents, and to ensure personal safety, all countries require that rearview mirrors must be installed on cars, and all rearview mirrors must be able to adjust direction.
19
3
Share

How to Solve the Hard Brake Issue in the 2013 Peugeot 408?

For the hard brake issue in the 2013 Peugeot 408, it is recommended to take the vehicle to a repair shop for brake inspection, regularly replace the brake fluid, and maintain the brake pads, brake hoses, and brake pump. Below is an introduction about the Peugeot 408: 1. Introduction to the Peugeot 408: The Peugeot 408 is a compact car launched by Dongfeng Peugeot on January 25, 2010, equipped with mainstream engines from DPCA, offering two displacement options: 2.0L and 1.6L. The launch of the Peugeot 408 greatly enriched Dongfeng Peugeot's product line in the 1.6L-2.0L golden displacement market. 2. Safety features of the Peugeot 408: The Peugeot 408 features a unique 6+X safety system, including EVA emergency brake assist, Bosch 8.1 version ABS anti-lock braking system, EBD electronic brake force distribution, TSC traction control, and ESP electronic stability program.
13
0
Share

How to adjust the center clock in the 2017 Passat?

For the 2017 Passat, press and hold the CLK button for about 5 seconds until the time display starts flashing. Use the adjustment keys (turn left to decrease, turn right to increase) and the hour/minute selection keys to set the time. Press CLK again to confirm. Below is some relevant information about the Passat: 1. Introduction: The Passat is a mid-size sedan designed by Volkswagen in Germany. It is classified as a B-segment car in Volkswagen's lineup. Since its debut in 1973, the Volkswagen Passat has set global standards in safety, classic design, and top-tier manufacturing quality for over 40 years. 2. Design: In terms of appearance, the new-generation Passat features Volkswagen's latest design philosophy—Fluid Harmony. The light-inspired front fascia, complemented by a flowing chrome trim, evolves Volkswagen's signature grille. The dot-matrix horizontal grille, dual-L-shaped full LED headlights, and a more robust hood together create a fresh front look.
6
2
Share

Why is the air conditioning in the Mercedes-Benz C200L not cooling?

The most common reasons for the air conditioning in the Mercedes-Benz C200L not cooling are insufficient quality and purity of the refrigerant, issues with the condenser and radiator, or problems with the expansion valve. The details are as follows: 1. Refrigerant: The quality and purity of the refrigerant play a crucial role in the vehicle's air conditioning system. Typically, poor-quality refrigerant can lead to inefficient operation of the air conditioning. Additionally, during the refrigerant charging process, the amount must be neither too much nor too little. Too little will result in insufficient pressure in the air conditioning pipes, while too much will cause excessive pressure. In both cases, the air conditioning will not function properly to cool. 2. C-Class Condenser and Radiator: The heat dissipation of the condenser and radiator also affects the performance of the air conditioning. Prolonged lack of cleaning can lead to the condenser and radiator being covered with debris and dust. 3. Quality of the Expansion Valve: The expansion valve is an important component in the refrigeration system, usually installed between the liquid storage tank and the evaporator. A poor-quality expansion valve will prevent the refrigerant from functioning as it should.
2
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.