How Many Kilometers Should Pulley Weights Be Replaced?

1 Answers
BrookeAnn
07/29/25 11:47pm
There is no specific replacement interval for pulley weights; it depends on the actual usage conditions. Pulley weights are one of the rotating components in a scooter's transmission system, categorized into light pulley weights and heavy pulley weights. Lighter pulley weights provide stronger acceleration, allowing the vehicle to reach a certain speed in a shorter time. Performance characteristics of pulley weights: If the pulley weights are heavier, the vehicle's power performance during acceleration may not be as good, resulting in slower acceleration and a longer time to reach high speeds. However, when the pulley weights slide to the outer edge of the pulley, the greater inertia allows the engine to operate at lower RPMs, making it more fuel-efficient during prolonged high-speed driving.
Was this review help?
18
5
Share
More Forum Discussions

What is the maximum lifting capacity a crane should not exceed?

The load rate of a crane generally should not exceed 60%. Below is an introduction to the dual-height limiter: 1. Introduction to the height limiter: A height limiter should be installed in the lifting mechanism. When the lifting device reaches the designed upper limit position, it should automatically cut off the lifting power source. Above this limit position, there should be sufficient remaining height to meet the requirements of the upward braking distance. A second-level lifting height limiter can also be installed to prevent over-travel and top collision. 2. Hazards of height limiter failure: During operation, if the crane operator fails to monitor the actual lifting height of the hook, it can cause the lifting mechanism to over-hoist and collide with the top, leading to the cutting and breaking of the lifting wire rope, which is the direct cause of the hook and load falling. Failure of the upper lifting limiter is also a significant factor in causing the lifting mechanism to over-hoist and collide with the top.
6
2
Share

How Many Kilowatt-Hours Does a Car Battery Equivalent To?

Car battery capacity is generally 80 kilowatt-hours. Below is some related information about car batteries: 1. Car Battery: A car battery, also known as a storage battery, is a type of battery that works by converting chemical energy into electrical energy. 2. Car Battery Maintenance: (1) Do not start the vehicle frequently. In winter, when the car is difficult to start, avoid continuous starting. Continuous starting of the motor will definitely cause the battery to over-discharge and be damaged. The interval between restarts should be more than 5 seconds. (2) When the battery has been in use for about two and a half years, routine maintenance should include battery testing to prevent issues. Try to avoid using electrical equipment such as the CD player or cigarette lighter when the vehicle is not running, and minimize the use of various in-car electrical devices while driving.
14
5
Share

What are the new regulations for taking the Subject 4 exam in another province?

Subject 4 exam new regulations for out-of-province applicants: Applicants only need to present their ID card to apply for a small vehicle driver's license (C1, C2, C5) anywhere in the country, and no longer need to submit residence permits or temporary residence certificates. Students just need to bring their ID card and photos to the local vehicle management office. Below are the relevant details about taking the driver's license exam in another province: 1. Nationwide application for small vehicle driver's licenses: Applicants can directly apply for a small vehicle driver's license with their ID card anywhere in the country, without needing to submit residence registration certificates, achieving a "one-card nationwide application" system. 2. Cross-regional subject exams: If an applicant has passed some subjects of the small vehicle driver's license exam and later changes their residence due to work, study, or life reasons, they can apply to change the exam location and continue taking the remaining subjects, reducing the burden of traveling back and forth for exams.
4
3
Share

Are Roewe and MG using the same engine?

Roewe and MG share the same engine model. The following aspects require attention when using the engine: Fuel must be clean: Excessive impurities in fuel will accelerate the wear of the electric fuel pump, reduce its service life, and degrade the engine's performance. Correct fuel selection: The engine has high requirements for fuel quality and grade, with even higher standards for EFI engines. Vehicles equipped with catalytic converters and oxygen sensors must use unleaded high-octane gasoline only. Timely fuel replenishment: The electric fuel pump in EFI engines must ensure sufficient fuel supply and stable working pressure for the injection system. When fuel in the tank is low, replenish it promptly to prevent fuel pump burnout.
3
3
Share

Is it necessary to purchase an extended car warranty?

It is necessary to purchase an extended car warranty. Here are the relevant introductions about the functions of an extended car warranty: 1. Car owners indirectly obtain extended warranty services: During the contract period, the maintenance costs are locked in, which can avoid unexpected huge expenses due to vehicle quality issues (such as engine, transmission assembly, steering system damage), reducing future worries. 2. Enjoy high-quality maintenance services: During the extended warranty period, the vehicle receives services from manufacturer-authorized 4S stores, which is the same as the repair process and solutions during the original factory warranty period, using genuine parts, eliminating the worry of repairs at roadside shops.
5
1
Share

What is the voltage of the LIN bus line?

The voltage of the LIN bus is 12V. The control units controlled by the LIN bus are generally distributed in close proximity to each other. Data transmission is single-wire, with the longest data line reaching up to 40m. The master node is configured with a 1kΩ resistor terminating to the 12V power supply, while the slave node is configured with a 30kΩ resistor terminating to the 12V power supply. Currently, the alliance is actively working to promote the LIN bus to achieve ISO international standards. The LIN bus conformance test specification is uniformly issued and managed by the LIN Alliance, and only core members of the LIN Alliance have access to it. This specification aims to unify the quality and performance of various LIN module nodes, ensuring the normal operation and safety of the entire vehicle after connecting to the LIN network. Therefore, OEMs in Europe and America require that the components provided by their suppliers must pass the certification report from a testing agency certified by the LIN Alliance.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.