How many kilometers should a Camry drive before changing the transmission oil?

1 Answers
DelMackenzie
07/29/25 9:10pm
Camry should have its transmission oil changed every 40,000 kilometers. Transmission oil needs to be replaced promptly when it reaches the replacement cycle. Over time, the transmission oil becomes dirty and its viscosity decreases, making it unable to effectively protect the transmission. This can lead to issues such as rough shifting, abnormal acceleration, loud noises, and in severe cases, premature transmission damage, shortening the transmission's lifespan. The Camry is a model under GAC Toyota, with body dimensions of 4900mm in length, 1840mm in width, and 1455mm in height, and a wheelbase of 2825mm. Appearance: The Camry Luxury version features a large trapezoidal horizontal grille, a streamlined body posture with a lower waistline, and an extended roof rear section that increases rear headroom. The Sport version adopts a three-layer grille front face, introduces a dual-tone body and "all-black" cabin design for the first time, and features a dual-sided quad exhaust pipe design at the rear.
Was this review help?
6
1
Share
More Forum Discussions

How often should the air conditioning filter of the Octavia be replaced?

The official recommendation for the Octavia's air conditioning filter replacement is every 25,000 KM or 36 months. More information about the air conditioning filter is as follows: 1. The car air conditioning filter should be selected from a reputable brand that is suitable for your vehicle model and guarantees quality. The air conditioning filter is a filter installed in the car's air conditioning system that can absorb dust particles and protect the air conditioning cooling system; 2. The air conditioning filter should be cleaned monthly and replaced every 30,000 KM or 2 years. Regular cleaning of the air conditioning filter can extend its service life. When replacing the air conditioning filter, if possible, use a specialized cleaner to clean the blower and air ducts. Note that the air conditioning filter has a top and bottom side, with an upward arrow marked on the filter—make sure not to install it upside down.
5
3
Share

Where is the tire pressure reset button on the Roewe 360?

The tire pressure reset button for the Roewe 360 is located on the center console, marked with the TPMS button. The specific operation method for tire pressure reset is to press and hold the TPMS button when the tire pressure is normal. Below is additional information about the Roewe 360: 1. It is available in 7 models with two engine displacements, 1.5L and 1.4T, equipped with a 1.4T + 7-speed dual-clutch powertrain. 2. The Roewe 360 with the 1.5L engine comes in 4 models, divided into Elite and Luxury configurations, offering both manual and automatic transmission options. 3. The 1.4T engine is available in 3 models, with configurations ranging from high to low: Elite, Premium, and Flagship models.
19
2
Share

Is the power of the Bestune T77 sufficient for starting and climbing slopes?

The Bestune T77 is equipped with a hill descent control function, making its power sufficient for starting and climbing slopes. Below is extended information about the Bestune T77: 1. The Bestune T77's control configurations include ABS anti-lock braking, brake force distribution, brake assist, traction control, electronic stability control, hill start assist, hill descent control, and auto hold. 2. Safety features include front and side airbags, child seat anchors, tire pressure monitoring system, engine immobilizer, and seatbelt reminder. 3. The Bestune T77 is powered by a CA4GA12TD 1.2T direct-injection turbocharged engine across all models. Its maximum net power/speed is 100kW/5500rpm, and maximum net torque/speed is 204Nm/1600-4200rpm.
8
5
Share

What Causes the Jerking Sensation When Shifting Gears in an Automatic Transmission?

Automatic transmission jerking during gear shifts may be caused by clutch pressure leakage inside the transmission. Below are common causes and solutions: 1. Internal transmission clutch pressure leakage: Inspect clutch damage and perform repairs. 2. Blocked or poor transmission oil flow: Worn valve body, long overdue transmission fluid change leading to deterioration and reduced lubrication, excessively dirty transmission filter with poor filtration allowing wear particles to enter valve body. 3. Incorrect transmission fluid level: Verify whether transmission fluid meets standard level - both insufficient and excessive fluid can cause this issue. Vehicles with transmission dipsticks can check fluid level against standard markings when engine is running. 4. Solenoid valve damage: Sludge circulating in transmission fluid blocking oil passages in valve body may cause jerking, which over time leads to transmission overheating, harsh shifting, slippage and other transmission problems.
9
2
Share

How to Remove the Headlights of Baojun 730?

The headlights of Baojun 730 are fixed to the radiator frame with screws. Remove the screws on the radiator frame to take out the headlights. Below are the precautions for replacing the headlights of Baojun 730: 1. The car headlights are fixed to the radiator frame with screws, and the headlights have headlight brackets. When installing the headlights, be careful with the tightening force of the screws to avoid damaging the headlight brackets. 2. To remove the headlights, the front bumper needs to be removed. During the removal process, avoid damaging the paint of the front bumper. Removing the front bumper makes it easier to take out the headlights. 3. After replacement, adjust the illumination direction and check the lighting position and brightness. 4. When replacing the lights, do not damage the original wiring of the car or install additional electrical devices. Damaging the original wiring or arbitrarily installing electrical devices can affect the car's risk of spontaneous combustion and pose safety hazards for future use.
7
5
Share

Why Is the Transmission Making Abnormal Noises?

Abnormal noises from the transmission may be caused by bearing wear or poor gear meshing inside the transmission. Bearing wear, looseness, or constant meshing gear noise: If abnormal noises are heard from the transmission when in neutral, and the noise disappears when the clutch is depressed, it is usually due to wear or looseness of the front and rear bearings of the transmission's first shaft or noise from the constant meshing gears. If the noise occurs in all other gears, it is mostly due to the rear bearing of the second shaft. For severely loose or damaged bearings, they should be promptly sent to a repair shop for maintenance or replacement. Poor gear meshing inside the transmission: If abnormal noises occur in the transmission during low-speed driving and persist during acceleration and gear shifting, it may be caused by poor gear meshing inside the transmission.
2
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.