How many kilometers for maintenance with Toyota Genuine Oil 0w20?

Does Transmission Fluid Need to Be Changed?

Transmission fluid does need to be changed. Here are the relevant details about transmission fluid replacement: 1. Dry dual-clutch transmissions and manual transmissions have similar structures, so they both use synthetic transmission fluid with a service life of approximately 150,000 kilometers. Most automatic transmissions require fluid replacement every 60,000-80,000 kilometers. 2. The transmission fluid replacement interval is only a general guideline. Due to factors such as driving conditions and habits, the condition of the transmission fluid may vary. If the vehicle experiences symptoms like rough shifting, strong jerking sensations, or significantly increased noise during operation, it's necessary to check whether the transmission fluid needs replacement. 3. There are three common methods for changing transmission fluid: (1) Gravity drain: Similar to engine oil changes, this involves loosening the transmission drain plug to release the fluid, then refilling through the fill port. The drawback is that gravity draining doesn't completely remove all old fluid. (2) Machine flush: A transmission flush machine connects to the transmission's fluid lines, using new fluid to push out the old fluid from inside the transmission. The advantage is more thorough replacement, while the disadvantages include being time-consuming and requiring more transmission fluid. (3) Removing the transmission pan: The advantage is the ability to clean or directly replace the transmission filter, with relatively thorough fluid replacement. The drawback is the more complicated installation process.

18

0

Share

What does 91h on a tire mean?

Tire 91h indicates that the maximum load capacity of a single tire is 615Kg, and the maximum speed it can withstand under the specified load is 210KM/h. Here are the relevant details: 1. 91 is called the load index, and the maximum load capacity of 615Kg can be determined by referring to the tire load index chart. 2. H is called the speed rating. Additional information: Whether it's the speed rating or the load index, during daily driving, you should operate within the specified limits of the speed rating or load index. Otherwise, there could be significant safety hazards. Additionally, when replacing tires, it's important to note that you should not mix tires of different types, models, or tire structures.

8

4

Share

Is the Teana clutch a dry type?

Teana clutch is a dry clutch. The clutch plate is a composite material primarily functioning through friction while also meeting structural performance requirements. Automotive friction materials are mainly used to manufacture brake friction plates and clutch plates. The working principle of the clutch is as follows: 1. Disengaged when depressing the clutch pedal: When starting the vehicle, the driver depresses the clutch pedal, which pulls the pressure plate backward, separating it from the friction plate. At this point, the pressure plate does not contact the flywheel, eliminating relative friction. 2. Fully engaged when not depressing the clutch pedal: During normal driving, the pressure plate tightly presses against the flywheel's friction plate, achieving maximum friction between them. The input and output shafts maintain relative static friction with identical rotational speeds. 3. Partially engaged during semi-engagement: The friction between the pressure plate and friction plate is less than in full engagement. The pressure plate and flywheel's friction plate enter a sliding friction state, where the flywheel's speed exceeds the output shaft's speed, transmitting partial power from the flywheel to the transmission. In this state, the engine and drive wheels establish a flexible connection.

6

3

Share

Which Gear Should a Manual Transmission Car Be in When Going Downhill?

When parking a manual transmission car downhill, engage the reverse gear to prevent forward sliding. When starting, first press the clutch, shift to neutral, start the vehicle, and then shift to the starting gear. The steps for starting a manual transmission car are: 1. Sit properly in the car; 2. Start the car; 3. Press the clutch; 4. Engage the 1st gear; 5. Slowly release the clutch; 6. Gently press the accelerator; 7. Fully release the clutch to complete the car's start. The reasons for a manual transmission car stalling after ignition are: 1. Use of substandard or poor-quality fuel; 2. Issues with the car's engine or fuel system; 3. Engine carbon buildup; 4. Excessive dirt on the idle motor valve core and throttle seat; 5. Releasing the clutch too quickly when starting.

15

5

Share

What Causes Rapid Loss of Car Coolant?

The main reasons for rapid consumption of engine coolant are: 1. Poor cooling system design. 2. Inefficient circulation leading to fast consumption; When adding coolant, it should be done after the engine temperature has cooled down. During the process, start the engine and gently press the accelerator to expel air from the system. Add the coolant slowly to ensure proper filling. If necessary, follow the manual's instructions to bleed the cooling system. 3. Leakage; Usually, traces can be seen at the leakage points. 4. Coolant entering the cylinder and being burned or entering the oil pan. In mild cases, there will be no water in the oil pan, while in more severe cases, water will be present, and the engine will run unsteadily. Do not immediately assume the issue is with the cylinder head gasket—a damaged intake manifold gasket can also cause coolant to enter the cylinder, as some engines have coolant passages in the intake manifold. If the coolant is being burned significantly, the engine exhaust pipe will emit water and white smoke.

3

5

Share

What is the correct way to depress the clutch?

The correct method for depressing the clutch is as follows: 1. Starting on flat ground. After pressing the clutch and shifting gears, when the car's speed hasn't picked up yet, the clutch should be released slowly. Releasing the clutch too quickly can cause the engine to stall. You can wait until the clutch is fully released before applying the throttle, as coordinating the throttle and clutch requires relatively high skill. 2. Starting on a slope. Hill starts are one of the most challenging aspects of driving. Even slowly releasing the clutch can sometimes cause the engine to stall, let alone releasing it immediately. The correct operation should be to slowly release the clutch until the engine starts to vibrate, then release the brake pedal and immediately step on the accelerator. If you're not proficient, you can also use the handbrake to ensure driving safety. 3. Shifting from first to second and second to third gears requires slow clutch release, while shifting from third to fourth and fourth to fifth gears allows for quicker release. When the car speed is low, the clutch should be released slowly to avoid strong jerking sensations. Once the speed increases, quickly releasing the clutch will hardly cause any noticeable jerking. In summary, when shifting between first, second, and third gears (low-speed gears), slow release is necessary to prevent stalling and jerking; when shifting between third, fourth, and fifth gears (high-speed gears), a slightly quicker release is acceptable.

15

0

Share

How many kilometers for maintenance with Toyota Genuine Oil 0w20?

Does Transmission Fluid Need to Be Changed?

What does 91h on a tire mean?

Is the Teana clutch a dry type?

Which Gear Should a Manual Transmission Car Be in When Going Downhill?

What Causes Rapid Loss of Car Coolant?

What is the correct way to depress the clutch?

Can You Still Drive When the Engine Malfunction Indicator Light Is On?

What are the reasons for engine oil deterioration?

Can I Change the Coolant Myself?

What are the symptoms of a faulty car temperature sensor?