How many kilograms should the cylinder head screws of the Bora be tightened to?

Does a Non-Functioning High-Mount Stop Light Affect Annual Inspection?

A non-functioning high-mount stop light will definitely cause the vehicle to fail the annual inspection. It must be repaired before passing the inspection. This is because the high-mount stop light is categorized as one of the vehicle's lighting components. According to national regulations, motor vehicles must periodically pass inspections covering exhaust emissions, exterior appearance, lighting systems, brakes, chassis, etc., and must have no traffic violation records to receive the inspection compliance certificate. Below is relevant information: 1. The high-mount stop light is designed to allow vehicles behind to accurately detect braking actions, thereby reducing the probability of rear-end collisions. 2. A non-functioning high-mount stop light can be particularly hazardous for trucks or buses with high chassis. Even if the vehicle still has two working brake lights, they may be difficult to see clearly (due to angle issues), significantly increasing the risk of rear-end collisions. Therefore, it is crucial to promptly repair the high-mount stop light to avoid unnecessary accidents.

19

3

Share

What Causes Reduced Airflow in Car AC While It's Still Cooling?

Reduced airflow in car air conditioning is caused by a clogged cabin air filter. AC System Layout: Different types of AC systems have varying configurations. Modern passenger vehicles commonly use integrated heating-cooling systems. These systems combine components like the evaporator, heater core, centrifugal blower, and control mechanisms into a single unit called the AC assembly. AC System Components: Contemporary AC systems consist of refrigeration, heating, ventilation, air purification devices, and control systems. A typical automotive AC system mainly includes components such as the compressor, electromagnetic clutch, condenser, evaporator, expansion valve, receiver-drier, refrigerant lines, condenser fan, vacuum solenoid valve, idle speed controller, and control system.

10

0

Share

What Causes Body Shaking During Acceleration?

Body shaking during acceleration can be caused by the following reasons: 1. Severe engine carbon deposits: The most common cause of car shaking is a dirty throttle or excessive carbon buildup in the fuel injectors. When there is too much carbon inside the engine, the gasoline sprayed by the cold-start injector will be largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making it difficult to start. In this situation, the car will only start easily once the carbon deposits have absorbed enough gasoline to become saturated. After starting, the gasoline adsorbed on the carbon deposits will be sucked into the cylinders by the engine's vacuum and burned, making the air-fuel mixture too rich. The engine's combustible mixture will fluctuate between too lean and too rich, causing idle shaking after a cold start. The lower the temperature, the more fuel is required for a cold start, and the presence of carbon deposits will significantly affect whether the cold start proceeds smoothly. 2. Issues with the ignition system: Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or weak sparking from the spark plugs can also lead to such problems. 3. Unstable fuel pressure: If you have already cleaned the engine carbon deposits, throttle, replaced the gaskets and spark plugs, but still notice body shaking at idle, it is recommended to visit a 4S shop to check the fuel supply pressure and the intake pressure sensor. Abnormal fuel pump pressure or incorrect readings and poor performance of the intake pressure sensor can both cause body shaking. 4. Aging engine components: Car shaking can also be related to the aging of engine mounts (also known as engine cushions). Engine mounts are essentially the shock absorption system of the engine, responsible for absorbing minor vibrations during engine operation. If the engine mounts are faulty, these vibrations will be transmitted to the steering wheel and the cabin, causing shaking at idle.

5

4

Share

Brief Steps for Replacing a Fuel Filter

Fuel filter replacement steps are as follows: 1. Park the vehicle on a solid, level surface. 2. Depressurize the fuel system (loosen the valve cap to release fuel system pressure). 3. Start the engine and let it run until the fuel in the lines is depleted and the engine stops. 4. The fuel filter is typically located beneath the engine or fuel tank. If necessary, use a jack to lift the vehicle and disconnect the fuel lines from the fuel filter. 5. Remove the mounting bolts of the fuel filter, then detach the old fuel filter. 6. Compare the new fuel filter with the removed one to ensure they are the same model. After confirmation, install the new fuel filter, paying attention to its orientation to ensure it points toward the engine. Secure it with the mounting bolts once properly aligned. 7. Reconnect the fuel lines and install the fuel pump fuse. 8. Reconnect the battery, then lower the vehicle to complete the process.

18

2

Share

At what tire pressure will a tire burst?

An automotive tire pressure of 280 kPa will not cause a tire to burst. Generally, car tires only burst when the pressure exceeds 420 kPa or even higher, as manufacturers typically leave a 30% safety margin in their recommended tire pressure specifications. The maximum pressure a tire can withstand ranges between 350-420 kPa. Even when inflating tires excessively during summer conditions, it's extremely difficult to reach the tire's pressure limit. Therefore, tires are not as prone to bursting under high-pressure conditions as one might assume. Below is relevant information: 1. A tire pressure of 280 kPa can cause abnormal tire wear, with the center of the tread wearing more severely than the shoulder areas, which shortens the tire's service life. It also reduces the tire's friction and grip, extending braking distances. 2. The tire becomes harder, compromising ride comfort and increasing vehicle vibration, which indirectly affects the lifespan of suspension components and other parts.

5

3

Share

What Are the Reasons for No Sound in Car Music Playback?

Car suddenly having no sound could be due to a dead battery, or issues with the fuse box and wiring. Importance of Audio System: Car audio is a crucial way for drivers to combat fatigue during journeys, playing a vital role in safe driving and overall vehicle safety. Therefore, it should never be neglected. Checking the Audio System: Determine if the car's audio system has been modified. If so, check the modified fuse or see if the audio output cable has come loose. If the issue persists, consider whether the speakers might be faulty. However, car audio systems are generally designed to alleviate the monotony of travel for drivers and passengers, featuring high standards in sound quality, operation, and vibration resistance to ensure stable performance and perfect sound quality.

2

4

Share

How many kilograms should the cylinder head screws of the Bora be tightened to?

Does a Non-Functioning High-Mount Stop Light Affect Annual Inspection?

What Causes Reduced Airflow in Car AC While It's Still Cooling?

What Causes Body Shaking During Acceleration?

Brief Steps for Replacing a Fuel Filter

At what tire pressure will a tire burst?

What Are the Reasons for No Sound in Car Music Playback?

How to Activate the Lock Sound on a Toyota?

Why can't the ball of the interior rearview mirror snap into place?

What to Bring for Motorcycle License Written Test (Subject 1)?

How Many Days Does It Take to Complete the Vehicle Transfer and Relocation Process in Dalian?