How many hours of check-in are required for Jiangxi Subject 2 before scheduling an appointment?

1 Answers
OAnderson
07/29/25 9:24pm
For the Subject 2 test of a C1 driver's license in Jiangxi, a total of 26 credit hours are generally required, including 2 hours for theoretical knowledge and 24 hours for practical operations. Only the practical operations require check-in, so the check-in time for Subject 2 is typically 24 hours. Below is an extended introduction: Subject 2 content: Theoretical knowledge includes basic driving operation standards and site driving knowledge, usually arranged for 2 hours of study. Practical operations include driving posture, pre-driving vehicle inspection and adjustment, getting in and out of the vehicle, starting and stopping, speed changing, gear shifting, reversing, driving position and route, as well as the five test items: reversing into a garage, stopping and starting on a slope, parallel parking, curve driving, and right-angle turns, usually arranged for 24 hours of study.
Was this review help?
7
1
Share
More Forum Discussions

What is the license plate code Lu R for?

Lu R is the license plate code for Heze, Shandong Province. The license plate codes for various cities in Shandong Province are as follows: Lu A for Jinan, Lu B for Qingdao, Lu C for Zibo, Lu D for Zaozhuang, Lu E for Dongying, Lu F for Yantai, Lu G for Weifang, Lu H for Jining, Lu J for Tai'an, Lu K for Weihai, Lu L for Rizhao, Lu M for Binzhou, Lu N for Dezhou, Lu P for Liaocheng, Lu Q for Linyi, Lu R for Heze, Lu S for Laiwu, Lu U as supplementary for Qingdao, Lu V as supplementary for Weifang, Lu Y for Yantai. License plates serve as identification and information registration for vehicles, with the primary purpose of identifying the vehicle's registered region and enabling the tracing of the vehicle's owner and registration details through the license plate number.
2
5
Share

Who is Liable for a Collision During the Driving Test (Subject Three)?

During the Subject Three driving test, the student is not held responsible for a collision. According to the traffic police's accident liability determination, the examiner bears full responsibility. Below are the specific details: 1. Legal Basis: Article 20 of the "Regulations for the Implementation of the Road Traffic Safety Law" states that if a student commits any road traffic safety violations or causes a traffic accident during driving practice, the instructor shall be held liable. 2. During Driving Practice: When learning to drive on the road, it must be conducted on routes and at times designated by the traffic management department of the public security authority. The practice must be carried out in a training vehicle under the guidance of an instructor, and no unrelated individuals are allowed in the vehicle. If a student commits any road traffic safety violations or causes a traffic accident during driving practice, the instructor shall be held liable.
13
1
Share

How to Use the Cruise Control System?

Method for using the cruise control system: 1. Press the power key to turn on the system, at which point the cruise control indicator on the dashboard will light up; 2. Accelerate to the desired speed (above 40km/h) and press the SET key, then you can release the accelerator with your right foot, and the speed will be set at the current speed; 3. Press "RES+" to increase the speed at the current speed, or press "SET-" to decrease the speed at the current speed; 4. The cruise control can be deactivated by stepping on the brake, pressing the cancel (CANCEL) key, or pressing the power (ON/OFF) key; 5. If the cruise control was canceled by stepping on the brake or pressing the cancel key, you can press the RES key to restore the previous cruise control speed.
12
5
Share

Should Cars Be Warmed Up in Winter?

In winter, cars should be warmed up for about 3-4 minutes. Here is an introduction to the warm-up time for cars in winter: 1. Too short a time can easily cause engine wear. 2. Too long a time can easily cause engine carbon buildup. 3. Warming up the car for 3-4 minutes in winter is beneficial for protecting the engine. 4. It allows the engine oil to fully reach all lubrication points and heats up various parts to achieve normal clearance, enabling full-load operation with minimal engine wear. The reasons for warming up a car in winter are as follows: 1. Mainly to allow the engine oil to achieve the best lubrication effect. 2. To allow the automatic transmission fluid to reach working pressure. 3. During a cold start, the crankshaft speed rises sharply, and the oil cannot reach the bearing positions in time, which can easily cause bearing damage, shorten the engine's service life, and increase engine noise. 4. Starting to drive immediately after a cold start can lead to insufficient pressure in the automatic transmission accumulator, causing strong impacts and rapid wear of the clutch plates.
4
0
Share

What grade of gasoline does the Volkswagen CC generally use?

The Volkswagen CC uses 97-octane premium unleaded gasoline, which must comply with the standards of GB18352.5-2013 and GB17930-2013. Here is more information about the Volkswagen CC: 1. The Volkswagen CC is a standard coupe under the Volkswagen brand. 2. It is equipped with Michelin PS3 series tires, sized 235/45-R17, offering excellent sports performance, along with a 4-door frameless design that combines comfort and dynamism. 3. The interior features a distinct sporty style, continuing the design language of Volkswagen's high-end business sedan series. The high-quality leather sports seats and the leather-wrapped intelligent sports steering wheel highlight the CC's characteristics of speed and dynamic passion. 4. The Volkswagen CC is powered by a 3.6L V6 FSI engine, delivering a maximum power output of 220 kW (300 hp) and a peak torque of 350 N·m at 2400-5300 rpm.
16
3
Share

How to Pair and Set Up the Remote Control?

Car remote control pairing and setup method is as follows: 1. Enter the car and close all doors. Use the original car key to turn the ignition "on" and "off" twice, then remove the key. Complete this within 5 seconds; 2. Press the "lock" and "unlock" buttons on the new remote simultaneously. Ensure both buttons are pressed at the same time. When the dashboard indicator light flashes once, it indicates success. Immediately switch to the original remote after success; 3. Press the "lock" and "unlock" buttons on the original remote simultaneously. Ensure both buttons are pressed at the same time. The indicator light will flash once to indicate success (when step 2 ends, press the original car remote immediately after the indicator light flashes once); 4. After both remotes are successfully paired, turn the ignition "on" and "off" once to end the pairing process. If multiple pairing attempts fail, disconnect the car's power for half an hour before trying again.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.