How many hours can a private car run continuously?

1 Answers
GiselleMarie
07/29/25 7:06pm
Private cars can run continuously for about 12 hours. Here is an introduction to the continuous driving duration of private cars: Driving duration and hazards: If a car is allowed to drive continuously on the highway at the current speed limit of 120 km/h, it can run for more than ten hours without any problems. However, the mileage is different. If a single trip exceeds 5000 km, it will cause significant damage to the car. Additionally, prolonged driving can lead to driver fatigue, increasing the risk of traffic accidents. The impact of long-distance driving on tires: If driving continuously for 12 hours, the car's tires will experience severe wear, especially in summer when the ground temperature is very high, which can further accelerate tire wear. Moreover, the friction between the tires and the ground decreases, increasing the possibility of a tire blowout. Under accelerated driving conditions, there is also a risk of the car overturning.
Was this review help?
5
0
Share
More Forum Discussions

How to reset the maintenance light on Changan CS75 Plus?

The method to reset the maintenance light on Changan CS75 is as follows: 1. Turn the car key to the ON position (full vehicle power-on state), which means turning the key twice or pressing the start button twice for keyless start, then press the selection button on the left side of the steering wheel as indicated in the red-marked area in the diagram; 2. Press and hold the reset button for about 5 seconds (do not release the reset button). Turn off the vehicle power while still holding the reset button, then turn on the full vehicle power again. You will see that the maintenance reminder has been cleared. Taking the 2021 Changan CS75 as an example, it is a compact SUV with body dimensions of: length 4650mm, width 1850mm, height 1715mm, a wheelbase of 2700mm, a fuel tank capacity of 58 liters, and a curb weight of 1600kg.
7
3
Share

Is it normal for a CVT to jerk slightly at start-up and then run smoothly?

It is normal for a CVT to jerk slightly at start-up and then run smoothly. A CVT refers to a continuously variable transmission, which is a type of automatic transmission in vehicles. It can continuously obtain any transmission ratio within the speed range, achieving optimal matching between the drivetrain and engine conditions through continuous variable transmission. Transmissions are categorized into AT (automatic transmission), CVT (continuously variable transmission), AMT (automated manual transmission), and DCT (dual-clutch transmission). Transmission working principles: 1. Manual transmissions consist of gears and shafts, achieving speed and torque changes through different gear combinations. 2. Automatic transmissions are composed of torque converters, planetary gears, and hydraulic control systems, achieving speed and torque changes through hydraulic transmission and gear combinations.
15
1
Share

How to operate the automatic parking of Audi A4L?

Automatic parking operation method: Press the automatic parking button, the indicator light will turn on, and the instrument display will show to drive forward. Continue driving until the car is approximately aligned with the front car or even further forward, until the instrument display shows R, then stop. At this point, shift into D gear, lightly press the brake to control the speed, and the car's computer system will take over the steering wheel and complete the parking. The following is an introduction to automatic parking: 1. Automatic parking means that after the driver finds an ideal parking spot, they only need to gently press the button, sit back, and relax, and everything else will be completed automatically. 2. Automatic parking can only be activated when parallel parking and the parking space is at least 1.5M longer than the car. 3. The automatic parking system is assisted by 12 radars, with 4 on each side of the car body responsible for detecting parking spaces, and the other radars assisting in parking.
8
2
Share

What causes the slow response of the exhaust camshaft position in Volvo XC60?

Volvo XC60's slow response of the exhaust camshaft position could be due to a damaged camshaft position sensor or weak signal, requiring professional inspection. The camshaft position sensor is a sensing device, also known as a synchronization signal sensor. It serves as a cylinder identification and positioning device, inputting camshaft position signals to the ECU, which is the main control signal for ignition. Relevant information about the camshaft position sensor is as follows: 1. The function of the camshaft position sensor is to collect the camshaft's dynamic angle signal and input it into the electronic control unit (ECU) to determine the ignition timing and fuel injection timing. 2. The camshaft position signal is used to identify the first ignition timing when the engine starts. Because the camshaft position sensor can identify which cylinder piston is about to reach the top dead center, it is also called a cylinder identification sensor.
12
5
Share

How to Use Automotive Air Conditioning Leak Sealer?

Usage method of automotive air conditioning leak sealer: 1. Turn on the air conditioning cooling system to maximum, open the cap and ensure the air conditioning compressor is running. If the air conditioning lacks refrigerant, replenish refrigerant until the clutch engages and starts operating, and the compressor runs; 2. Shake the bottle to mix the refrigerant with the leak sealer. Start the engine and turn on the air conditioning cooling system to maximum. Hold the bottle upside down at the low-pressure filling port, turn the valve clockwise, and gently shake until the bottle is empty. Disconnect the filler, remove the bottle from the hose, and turn the manual valve counterclockwise until the perforation rod is in the upper position. After filling with the necessary amount of refrigerant, run the air conditioning system for 15 minutes to allow the leak sealer and refrigerant to circulate thoroughly.
16
0
Share

Can I Wear Glasses During the Driver's License Physical Examination?

It is acceptable to wear glasses if you have difficulty seeing during the physical examination. If you wear glasses for the photo taken during the examination, you must also wear them during the actual driving test. This is because the examiner will photograph the test process, and failing to comply with this rule may result in disqualification. Therefore, it is advisable to maintain the same appearance during the test as during the physical examination. According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," applicants for a Class C driving license must have a naked or corrected visual acuity of at least 4.9 on the logarithmic visual acuity chart, while applicants for Class A or B licenses must achieve a visual acuity of 5.0 or higher. Therefore, individuals with myopia or hyperopia can meet the required vision standards by wearing glasses during the physical examination.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.