How Many Days in Advance Can a Motor Vehicle Undergo Annual Inspection?

1 Answers
Tammy
07/29/25 11:34pm
Vehicle annual inspection can be performed up to 90 days in advance. According to Article 32 of the Motor Vehicle Registration Regulations, the owner of a motor vehicle may apply for an inspection compliance mark at the vehicle management office of the registration location within three months before the expiration of the motor vehicle's inspection validity period. More relevant information is as follows: 1. Consequences of overdue inspection: If a vehicle that has not undergone annual inspection continues to be driven on the road, it will be subject to a fine and a three-point penalty, and the vehicle will also be temporarily impounded. 2. Inspection time calculation: The annual inspection time for a vehicle is not based on a specific date, but is calculated by month. If the annual inspection is overdue, the previously purchased car insurance will not take effect. If a traffic accident occurs during this period, the insurance company will not compensate for it.
Was this review help?
4
1
Share
More Forum Discussions

What is the Clutch Called for Braking?

The clutch is referred to as the brake for stopping. Below is relevant information about the clutch: 1. Clutch: The clutch is located within the flywheel housing between the engine and the transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output shaft of the clutch serves as the input shaft of the transmission. While driving, the driver can press or release the clutch pedal as needed to temporarily separate or gradually engage the engine with the transmission, thereby cutting off or transmitting the power from the engine to the transmission. 2. Principle of Releasing the Clutch: The principle of releasing the clutch is: 'Slow at first, then fast, and finally synchronized.' When initially pressing down, it should be done quickly and all the way to the bottom. When lifting the pedal during the free travel phase, it should be fast, but slow as it nears the engagement point. Upon reaching the semi-engagement point, pause briefly before fully releasing. The key to this process is accurately finding the semi-engagement point. To effectively control the vehicle speed, use the semi-engagement point as the dividing line—lifting quickly above it and pressing down slowly below it, adjusting to find a speed that suits you.
9
4
Share

Does Modifying Interior Ambient Lighting Affect the Car?

Modifying the interior ambient lighting of a vehicle does not affect the car itself. This is because while driving, the electricity comes from the generator, not the battery. The battery is only used after the engine is turned off. Therefore, as long as the lights are not used for extended periods after turning off the engine, there will be no impact. Potential hazards of installing interior ambient lighting: It may affect the driving safety of the car. The color of the lights could interfere with normal safe driving. When driving at night, if the interior lights are on, the windshield acts like a mirror, reflecting the interior light into the driver's eyes. This can make it difficult for the driver to see darker road conditions ahead, increasing the risk of traffic accidents. Interior ambient lighting is a decorative illumination, typically in colors like red, blue, or green, mainly to make the car interior more vibrant at night, enhance the atmosphere, and create a certain mood. It's important to note that the color of the lights should not interfere with normal safe driving. To turn on the interior ambient lighting: First, turn the ignition switch to the ON position, then press the ambient light button to activate the ambient lighting mode.
2
2
Share

How to Quickly Deal with Insufficient Cylinder Pressure?

Here are the quick solutions for insufficient cylinder pressure: 1. Grinding or replacing the valves: Check the car's valves. If the pressure drop is caused by poor valve sealing, the valves should be ground or replaced. If the valve spring is broken, leading to insufficient pressure, the valve spring can be replaced. 2. Replacing the cylinder head gasket: Check for air leaks between the cylinder block and cylinder head. If the pressure drop is due to leakage between them, it can be easily resolved by replacing the cylinder head gasket.
15
4
Share

What is the Volkswagen Satigar?

The Volkswagen Satigar is the Volkswagen Sagitar, a compact sedan. Taking the 2019 Volkswagen Sagitar as an example, its body dimensions are 4753mm in length, 1800mm in width, and 1462mm in height, with a wheelbase of 2731mm. In terms of power, the 2019 Volkswagen Sagitar is equipped with 1.2T and 1.4T turbocharged engines. The 1.2T engine has a maximum power of 85 kilowatts and a maximum torque of 200 Newton-meters, while the 1.4T engine has a maximum power of 110 kilowatts and a maximum torque of 250 Newton-meters. For the transmission system, the 2019 Volkswagen Sagitar is paired with a 7-speed dual-clutch transmission and a 5-speed manual transmission.
7
2
Share

What is the ground clearance of the 2016 Nissan Qashqai?

2016 Nissan Qashqai has a ground clearance of 188cm, which reflects the vehicle's ability to pass over obstacles or uneven ground without collision. The 2016 Nissan Qashqai is an SUV with body dimensions of 4401mm in length, 1837mm in width, and 1593mm in height, and a wheelbase of 2646mm. In terms of interior, the 2016 Qashqai features a brand-new three-spoke flat-bottom multifunctional steering wheel, giving it a sporty feel. The inverted trapezoidal air vents above the central LCD screen enhance the interior's sense of layering. Exterior-wise, the 2016 Qashqai adopts a new-style rear bumper design, with large black plastic panels paired with a two-tone silver skid plate, giving it a fresh and innovative look.
18
1
Share

What do the two white dashed lines signify?

The double white dashed lines indicate a yield line. White dashed lines are among the most common road markings encountered in daily life. When marked along a roadway, they serve to separate traffic moving in the same direction or act as a guide for maintaining safe following distances. Upon approaching an intersection marked with these lines, vehicles must reduce speed. Pedestrians crossing at such intersections should ensure vehicles remain within the bounds of the double white dashed lines, and vehicles must not cross these lines. Yield lines are typically installed at intersections of secondary roads where visibility is relatively good. This measure is implemented to prevent traffic accidents. Therefore, when a vehicle approaches an intersection marked with yield lines, it must come to a complete stop to allow vehicles on the main road to proceed first. Only after the majority of main road traffic has passed may the driver continue. Other road marking meanings: Double dashed lines: This is a yield line, often used in conjunction with a yield sign. It consists of two parallel dashed lines and an inverted triangle. The inverted triangle is white with the character "yield" written on it. It indicates that vehicles must slow down or stop, observe the traffic conditions on the main road, and proceed only after ensuring the right of way for main road vehicles. Yellow dashed lines: Used to separate opposing traffic flows when crossing a roadway. When marked along the roadside or curb, they prohibit vehicles from parking for extended periods. Stop line: Stop lines are generally placed at intersections with poor visibility, requiring vehicles to come to a complete stop and observe before proceeding. Double white solid lines: These are stop and yield lines, used at pedestrian crossings without traffic signals, requiring vehicles to stop and yield to pedestrians.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.