How many days does it take to transfer the subject 4 exam to another location?

1 Answers
VanLily
07/29/25 4:25pm
Subject 4 cannot be taken in a different location. Simply put, Subject 4 must be taken in the same place as Subject 1, and cannot be taken in a different location due to different vehicle management offices. Below is relevant information about Subject 4: 1. Subject 4, also known as the Subject 4 theory test or driver theory test, is part of the motor vehicle driver's license assessment. The original examination consisted of the Subject 1 theory test, Subject 2 stake test, electronic Subject test, and Subject 3 road test. According to the Ministry of Public Security's Order No. 123, a theory test must be conducted after the road test. Since this test is conducted after Subject 3, it is commonly referred to as the Subject 4 test. However, there is no official term 'Subject 4' in the actual official documentation (i.e., the Ministry of Public Security's Order No. 123). 2. Subject 4 separates the requirements related to safe and civilized driving from Subject 1, including safe driving skills in complex conditions and emergency handling knowledge, and conducts them after the Subject 3 actual road driving test to further assess the candidate's level of traffic awareness.
Was this review help?
19
1
Share
More Forum Discussions

How to Handle Violations Before Taking the Driver's License Test?

If the vehicle owner's driver's license is revoked, traffic violation points cannot be processed. When handling related procedures, the driver's license must be in a normal status to proceed. If the driver's license is penalized on-site (receiving a ticket), the ticket must be brought to the designated payment office at the traffic police team where the violation occurred. For non-on-site penalties, use the driver's license to obtain a ticket at the traffic police team where the violation occurred and then proceed to the designated payment office.
13
1
Share

What to Do If There Are Bubbles in Window Tinting Film?

Simply find something to squeeze out these bubbles. Of course, this method only works for bubbles located at the edges of the film, as those in the middle cannot be addressed this way. The same approach applies to car window tinting. You can use a bank card or a bus card to squeeze out these bubbles, and the operation is quite simple. If the bubbles at the edges of the film have been squeezed out, you can use a small needle to puncture the bubbles in the middle. This method may seem a bit aggressive.
11
3
Share

How to Connect Bluetooth in an Older Model Cruze?

First, establish a pairing relationship. Turn on the Bluetooth functions of both your phone and the navigation device. Set the device to "Visible to All" and search for Bluetooth devices on your phone. After successful pairing, the connection is established. Once the navigation system and phone Bluetooth are successfully paired, enter the dialing interface from the navigation main screen. You can make and receive calls, and also import the phone's contact list to the navigation device. Enter the Bluetooth interface, click on Music, and simultaneously open the music player on your phone.
14
0
Share

How to Break in an Automatic Transmission New Car on the Highway

Keep the car under a certain load, meaning you can carry a few passengers or some cargo. Most automatic transmission cars are also manual-automatic, so if you're an experienced driver, it's best to start in manual mode. When breaking in the car on the highway, initially use manual mode to shift up one gear at a time. After switching to D mode, drive for another 20 kilometers—that's when the car is truly broken in. Once properly broken in, the fuel injectors will atomize fuel efficiently, making the car more fuel-efficient in the future.
18
1
Share

How to install the seat belt in Wuling Rongguang?

The installation of the rear seat belt in Wuling Rongguang requires that the angle between the shoulder strap of the seat belt and the horizontal line of the seat back should not exceed 45 degrees, and the maximum angle with the center line of the seat should be 20 degrees. The following is a detailed introduction to the installation of the rear seat belt in Wuling Rongguang: 1. Installation of the waist belt: When installing the waist belt, it should be noted that the two fixing points of the waist belt should be installed on the vehicle floor, seat frame, or side wall of the vehicle body. The position of the fixing point on the floor is related to the sitting point on the seat. The angle between the waist belt fixing point and the sideline and the horizontal reference line of the vehicle body should be as close to 45 degrees as possible. In addition, all positions within the seat adjustment range can be adjusted. This angle must be within a safe range. 2. Installation of the shoulder strap: The position range of the upper fixing point of the shoulder strap has been stipulated in relevant civil industrial standards and should be followed accordingly. The distance from the shoulder strap fixing point to the center line of the seat should not be less than 140mm. 3. Installation of accessories: Whether the installation position of accessories is appropriate or not is one of the important conditions that determine whether the seat belt can function effectively. Generally, it is required that the horizontal distance between the two lower installation accessories of the two-point and three-point seat belts should not exceed 350mm, and the distance between these two installation accessories and the center line of the seat should be as equal as possible.
19
4
Share

How to remove the center console of an Audi A6?

First, pull out the rear air vent. There is a screw for the center armrest inside. Remove the screw and take it out, then you can take off the armrest cover. To remove the center console, first take off the side trim panels on both sides, then remove the screws on top of the center console. After that, you can remove the armrest box. The cup holder is a plastic mold that is clipped in. Gently pry it open along the groove. Inside, there is an automatic transmission release pull ring.
11
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.