How many cylinders does the BMW X1 have?

1 Answers
LeRyan
07/29/25 10:49pm
BMW X1 is equipped with a four-cylinder engine. The function of the engine is to convert the heat energy of gasoline or diesel into mechanical energy by burning and expanding the gas in a sealed cylinder, thereby pushing the piston to perform work. The BMW X1 is a compact SUV with dimensions of 4565mm in length, 1821mm in width, and 1620mm in height, a wheelbase of 2780mm, and a fuel tank capacity of 61 liters. In terms of power, the BMW X1 is powered by a 1.5T turbocharged engine, delivering a maximum horsepower of 140PS, a maximum torque of 220Nm, and a maximum power of 103kW, paired with a 7-speed dual-clutch transmission.
Was this review help?
4
0
Share
More Forum Discussions

What to Do If You Lose the Key to Your Scooter?

Take the ignition switch to a professional locksmith to have a new key made. Generally, the price of a key is not expensive. Replace the lock directly. The fuel tank cap and ignition switch of the motorcycle use the same key, so in this case, both locks need to be replaced. For a DC ignition system, open the handlebar and connect the black and red wires inside with a large pin; for an AC ignition system, you also need to open the handlebar and cut the wires.
11
1
Share

How to Reset the Maintenance Light on the XRV?

First, press and hold the 'A' button while stepping on the brake pedal. Then, do not start the engine, but ensure the vehicle's power is turned on. At this point, the dashboard or characters may start flashing. Continue holding down the reset button 'A' until '...' appears on the display. Release the brake pedal and let go of the 'A' button. The maintenance light reset process is now complete. Finally, turn off the power.
12
1
Share

How to Renew an Expired Driver's License in a Different Location?

You need to process the renewal before the driver's license expires. If the license has already expired, you can only apply for renewal at the vehicle management office where the license was originally issued. Bring the driver's license, original and photocopy of the ID card, and physical examination proof issued by a county-level or above medical institution. Fill out the "Motor Vehicle Driver's License Application Form" at the vehicle management office. Generally, the renewal process takes about one to three days. The renewal of an expired driver's license in a different location should be applied for at the vehicle management office within 90 days before the license expires.
13
2
Share

How to Activate Voice Control in Camry?

Locate and press the settings button on the central control screen to open the settings page. Find the voice assistant option in the settings page and click to enable it. Once the voice assistant is enabled, you can activate it. The vehicle's voice control system works by recognizing voice commands after pressing the button and then executing them.
19
0
Share

Causes and Solutions for Steering Wheel Vibration in Cars

This occurs when the car is in motion due to loose ball joints in the tie rods or detachment of rubber bushings at the joints, as well as irregular tire wear. Replace the damaged components. This situation is mostly caused by tire deformation resulting from daily use conditions such as scraping, collisions, or aging. Replacing the tires will resolve the issue. Excessive or frequent braking may cause the brake discs and pads to overheat, leading to deformation upon cooling and resulting in steering wheel vibration. Generally, replacing the brake discs is required. A common cause is twisted or deformed drive shafts, or loose, dry, and rusted universal joints. It is advisable to have service personnel apply grease to lubricatable parts.
19
4
Share

How to Adjust Motorcycle Valve Clearance?

When adjusting the valve clearance, the piston must be positioned at the top dead center of the compression stroke; otherwise, the valve will be held by the rocker arm, making the valve clearance unadjustable. Use the kick starter to rotate the crankshaft. It is recommended to remove the spark plug and insert a small screwdriver into the spark plug hole from the cylinder head to touch the top surface of the piston. At the top dead center of the compression stroke, both valves are in the closed position, and there is clearance between the adjusting screw end face on the rocker arm head and the top surface of the valve stem.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.