How Many Colors Does the Geely Boyue Have?

What is the size of an R18 tire?

R18 tires are 18 inches in size. Here are some tire maintenance tips: 1. Regularly check tire pressure: Tire pressure is a crucial factor affecting tire lifespan. It should neither be too high nor too low; always inflate according to the vehicle's recommended tire pressure. In summer, try to keep the tire pressure slightly lower. In winter, ensure the tire pressure is slightly higher than in summer due to thermal expansion and contraction. 2. Inspect for wear: Some vehicles may experience uneven tire wear. Frequently check the inner side of the tires for abnormal wear, focusing on whether the tread depth is consistent on both sides. 3. Remove foreign objects promptly: Debris in the tire treads can pose potential hazards and may fly out while driving. 4. Perform wheel alignment regularly: If the vehicle pulls to one side or exhibits unusual steering behavior, get the tires aligned promptly to prevent further issues. Wheel alignment ensures even force distribution across all four tires, avoiding excessive wear.

1

5

Share

How long should you keep the engine running after a jump start?

After jump-starting the vehicle, you should keep the engine running for at least 30 minutes to ensure sufficient battery charge. A dead battery could be due to complete discharge or battery failure. If the battery is discharged, you can attempt to start the vehicle using another car and jumper cables. If the battery is damaged, it should be repaired or replaced promptly. Jump-starting method: 1. Connect the positive and negative terminals of the dead battery to the corresponding terminals of the donor vehicle using jumper cables, connecting the positive terminal first followed by the negative terminal. (Always connect positive to positive and negative to negative, avoiding reversed connections or contact between opposite terminals) 2. Keep the donor vehicle running while the recipient vehicle completes the above steps and starts normally. (After starting, the recipient vehicle should turn off all electrical accessories when possible) 3. The recipient vehicle should ideally run for over 30 minutes when conditions permit to fully recharge the battery.

3

1

Share

What does MT mean?

In automobiles, MT stands for Manual Transmission, also known as manual gearbox. It requires manually shifting the gear lever to change the gear engagement positions inside the transmission, altering the gear ratio to achieve the purpose of changing speeds. A manual transmission is a gear-shifting device used to modify the speed and torque transmitted from the engine to the drive wheels. It enables the vehicle to obtain varying traction and speed under different operating conditions such as starting from a standstill, climbing hills, turning corners, and accelerating, while also allowing the engine to operate within a more favorable range. Functions of manual transmission: Changing the gear ratio to expand the range of torque and speed variations at the drive wheels, adapting to frequently changing driving conditions. Under the premise that the engine's rotation direction remains unchanged, the reverse gear is used to enable the vehicle to move backward. With the engine still running, the neutral gear interrupts power transmission, which is beneficial for engine startup, warm-up, idling, and facilitates gear shifting, coasting, or temporary parking. The transmission can also divert engine power to drive other mechanisms, such as the winch on certain vehicles or the oil pump of dump trucks.

19

2

Share

How to Break in a New Car?

New car break-in methods are as follows: 1. Initial break-in: The first 500 kilometers is the initial break-in period, during which the speed should not be too fast, generally below 70-80 km/h, and the engine speed should preferably not exceed 2,200 rpm. 2. Mid-term break-in: 500-1,000 kilometers is the mid-term break-in period, where the maximum speed can be appropriately increased, generally up to 90-100 km/h, with engine speed preferably below 2,500 rpm. Appropriately increasing speed will not affect the engine but can promote break-in, and you can also check for any abnormalities during acceleration. 3. Final break-in: 1,000-1,500 kilometers is the final break-in period, during which the speed can be increased to below 120 km/h. Because break-in is a gradual process, it must be done step by step. The engine speed should not exceed 3,000 rpm.

14

1

Share

How Does a Car Braking System Work?

The working principle of a car braking system is to generate significant friction, converting the vehicle's kinetic energy into thermal energy, thereby achieving the braking effect. The components of a car hydraulic braking system are: 1. Control System: Pedal, handbrake. 2. Hydraulic System: Composed of hydraulic fluid, brake pump, and hydraulic lines. 3. Power Assist System: Vacuum booster pump. 4. Electronic Control System: Composed of ABS pump, ABS sensors, and ABS computer. 5. Execution System: Composed of brake calipers, brake pads, and brake discs. Additional Information: 1. A car braking system refers to a series of specialized devices that apply a certain force to specific parts of the car to enforce a certain degree of braking. 2. The functions of the braking system are: to enable a moving car to decelerate or even stop as required by the driver; to keep a parked car stationary under various road conditions; and to maintain a stable speed for a car moving downhill.

6

0

Share

What is the braking principle of the handbrake?

The braking principle of the handbrake: For small cars, some handbrakes are located behind the transmission, connected to the driveshaft, where there is a brake disc, similar to a disc brake (though drum brakes also exist). The pulling force is transmitted via a steel cable to achieve parking braking. Below are some precautions for using the handbrake: 1. Mechanical handbrake: Avoid pulling too tightly. For the most common mechanical handbrake, first, avoid pulling it too hard every time you park, especially not pulling it to the limit. Overstretching the metal or keeping it stretched for too long can accelerate deformation, leading to faster wear of the handbrake cable. The correct method is to pull the handbrake until the rear wheels lock, then lift it 1-2 notches further to ensure the car doesn't roll. 2. For automatic transmission cars: Engage the handbrake before shifting to P. For automatic transmission cars equipped with an electronic handbrake, when parking on a slope, always engage the handbrake to secure the car first, then shift the transmission into P to reduce the burden on the transmission and prevent the P lock from jamming, which could make it difficult to disengage.

15

1

Share

How Many Colors Does the Geely Boyue Have?

What is the size of an R18 tire?

How long should you keep the engine running after a jump start?

What does MT mean?

How to Break in a New Car?

How Does a Car Braking System Work?

What is the braking principle of the handbrake?

Can a car that has been using 92-octane gasoline switch to 95-octane gasoline?

Is It Easy to Learn to Drive an Automatic Car?

What causes the noise when turning the steering wheel while stationary?

What is the percentage of speeding when driving at 85 in an 80 speed limit zone?