How many class hours are required for Subject 2 test?

1 Answers
StNicole
07/29/25 12:46pm
For a C1 driver's license, Subject 2 requires 16 class hours, while a C2 license requires 14 class hours. The regulations regarding class hours are as follows: 1. Class hours may be increased but not reduced; 2. If test content and items are added, class hours must be increased accordingly; 3. Each student's daily learning time must not exceed 4 class hours. There are two common methods for recording class hours: 1. Students use their ID cards to clock in on a device, thereby recording driving practice hours; 2. The driving school issues a class hour card for students, managed uniformly by the instructor. When students come for practice, the instructor starts the clock to calculate class hours and clocks out when the session ends.
Was this review help?
12
2
Share
More Forum Discussions

How to Check the Tire Pressure of Haval F7?

To check the tire pressure of the Haval F7, press and hold the OK button for five seconds, then use the up and down adjustment buttons to navigate to the tire pressure display interface. Tire pressure should neither be too high nor too low. If the tire pressure is too low, the tires may experience wave-like deformation during high-speed driving, increasing the risk of a blowout. Conversely, if the tire pressure is too high, it reduces the contact area between the tires and the ground, negatively affecting the vehicle's grip and handling stability. The Haval F7 measures 4620mm in length, 1846mm in width, and 1690mm in height, with a wheelbase of 2725mm. The front and rear track widths are both 1585mm. Its engine delivers a maximum horsepower of 169Ps, a maximum power output of 124kW, and a maximum torque of 285Nm.
2
4
Share

How to switch the Great Wall pickup truck 2H4H4L?

The method to switch the Great Wall pickup truck 2H4H4L is to shift to N gear after parking for switching, then drive slowly for a short distance to allow engagement. 2H refers to high-speed 2-wheel drive, generally used in urban areas; 4H refers to high-speed 4-wheel drive, typically used on mountain roads with steep ascents/descents and sharp turns; 4L refers to low-speed 4-wheel drive, mainly used for pure off-road conditions like rally or obstacle courses. The Great Wall pickup, also known as the Wingle series, is a practical multi-purpose utility vehicle between sedans and trucks. The Great Wall Cannon model has dimensions of 5437mm(length)×1958mm(width)×1893mm(height) with a 3230mm wheelbase, delivering 190Ps maximum horsepower, 140kW peak power, and 360Nm maximum torque.
8
0
Share

What are the reasons for severe shaking when a car is just started?

Severe shaking when a car is just started can be caused by: 1. Transmission issues; 2. Problems with the clutch assembly; 3. The clutch pressure plate, pressure springs, and release levers not being on the same plane; 4. Jerky engagement between the transmission gears and drive shaft; 5. Uneven operation among the engine cylinders; 6. A dirty throttle body causing uneven air intake and operation; 7. Broken or burned-out high-voltage wires; 8. Spark plugs failing in some cylinders; 9. Poor tire balance. Body shaking is a common issue many car owners encounter. If noticeable shaking occurs when starting the vehicle or while idling with the engine running, it may indicate a problem that requires prompt inspection.
9
2
Share

What is Parallel Import?

Parallel import refers to the importation of products by importers without authorization from the relevant intellectual property rights holders. These products are originally placed on the market in other countries or regions by the rights holders themselves or with their consent, and are then imported into the country or region where the intellectual property rights holders or exclusive licensees are located. Parallel import cars, fully known as parallel trade import vehicles, are commonly referred to as parallel trade vehicles. Based on their different identities, parallel import vehicles can be divided into three main categories: modified vehicles, small-batch vehicles, and narrowly defined parallel import vehicles. Depending on the import region, they can also be classified as U.S.-spec vehicles, Middle East-spec vehicles, Canadian-spec vehicles, European-spec vehicles, etc. The required documents for purchasing a parallel import vehicle include: 1. Certificate of Imported Goods; 2. Vehicle Inspection Sheet; 3. Vehicle Conformity Certificate; 4. Vehicle Purchase Invoice; 5. Electronic Information of Imported Vehicles.
6
2
Share

Where is the intake manifold located?

The intake manifold is located between the carburetor or throttle body and the intake ports of the cylinder head. For carbureted or throttle body fuel-injected engines, its function is to distribute the air-fuel mixture from the carburetor or throttle body to the intake ports of each cylinder. For port fuel-injected engines or diesel engines, the intake manifold solely distributes clean air to the intake ports of each cylinder. The intake manifold must distribute the air-fuel mixture or clean air as evenly as possible to each cylinder. To achieve this, the length of the gas flow passages inside the intake manifold should be as equal as possible. To reduce gas flow resistance and improve intake efficiency, the inner walls of the intake manifold should be smooth.
5
1
Share

Can Fuel Additives Be Added After a Full Tank?

Fuel additives should not be added after a full tank. They should be added to the fuel tank before refueling, and then the refueling process should begin. During the gasoline injection into the tank, there will be a continuous and intense mixing process, which accelerates the dispersion of the fuel additive. Fuel additives, commonly known as the third generation of gasoline detergents, are also referred to as gasoline detergents or fuel additives. The purpose of fuel additives is to address carbon deposits in the fuel system of fuel-injected vehicles, quickly restore the engine to optimal working conditions, and compensate for certain deficiencies in gasoline properties while imparting new beneficial characteristics. They improve atomization, reduce wear, protect the engine, and lower emissions, among other benefits.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.