How many body colors does the Corolla have?

1 Answers
VonSophia
07/29/25 9:26pm
The Corolla comes in 8 body colors, which are Super White, Pearl White, Silver Metallic, Black Mica, Platinum Bronze Metallic, Red Mica Metallic, Light Yellow Mica Metallic, and Dark Brown Mica Metallic. The Corolla's body dimensions are: length 4635 mm, width 1780 mm, height 1455 mm, wheelbase 2700 mm, ground clearance 152 mm, fuel tank capacity 50 liters, and the body structure is a 4-door 5-seater sedan. The Corolla is equipped with a 1.2T turbocharged engine, with a maximum power of 85 kW, maximum torque of 185 Nm, paired with a 10-speed continuously variable transmission.
Was this review help?
10
5
Share
More Forum Discussions

How to Replace the Battery in a Mercedes Remote Key?

Mercedes remote key battery replacement steps are as follows: 1. From the tail of the key, push up the marked switch, and the hidden mechanical key will pop out slightly. 2. Then you can take out the mechanical key. 3. Use the just removed mechanical key to press against the marked position, apply a little force, and the key shell can be opened. 4. After replacing with a new battery, ensure the battery's positive and negative poles are not reversed, then proceed with installation—insert the top of the shell first, then press the other end firmly. In daily use, dropping the car key from a height can easily damage it. Another scenario is water ingress into the key; if water seeps inside and damages the circuit, it can also cause the remote to malfunction.
3
4
Share

How Many Times Can You Take the Driving Test Part 2?

You can take the Driving Test Part 2 up to five times, meaning you can schedule the test five times. Each scheduled test gives you two attempts. If you fail both attempts, you will need to retake the test. The rules for the Driving Test Part 2 are as follows: 1. You have two attempts during each test session, and you must pass all five test items in each attempt. If you fail any item, you must retake all five items. Note that starting from the third test session, you will need to pay a retake fee for each subsequent session. 2. If you fail the first attempt, you will immediately proceed to the second attempt, following the same process as the first attempt, using the same vehicle and the same test route. You will also need to verify your fingerprint again.
11
0
Share

How to park at the designated point during uphill start?

Parking at the designated point during uphill start is as follows: 1. Approach the right roadside line: After hearing the voice command, start this test item, control the speed, turn on the right turn signal, and slowly steer towards the right roadside line. 2. Maintain straight direction: When the right front corner of the engine cover (1/3 position) aligns with the roadside line, maintain straight direction while observing the entire body's position relative to the line through the right rearview mirror. 3. Three-point alignment: When the raised point on the right wiper, the pole of the parking sign, and your eyes form a straight line (three-point alignment), depress the clutch and brake to stop. 4. Exit the test area: After the voice prompt, complete the hill start within 30 seconds. When the vehicle body shakes, keep the clutch steady and then exit the test area.
2
3
Share

Why does the car air conditioner not cool when driving at high speed?

When the car air conditioner does not cool properly during high-speed driving, the general cause is a malfunctioning expansion valve: 1. When the expansion valve is blocked: The refrigerant cannot flow smoothly in the air conditioning system, eventually leading to excessive pressure. Normally, the air conditioning compressor is driven by a belt, so theoretically, the higher the speed, the better the cooling effect should be. However, when there is moisture in the refrigerant, it can easily freeze at the expansion valve due to the high speed and high cooling power, causing blockage. This results in increased air conditioning pressure, leading to a loss of cooling. 2. Excessive sensor pressure: If the air conditioning pressure sensor detects excessively high pressure, it will stop the compressor from working. This is why the air conditioner stops cooling when the car is driven at high speeds.
15
5
Share

What Are the Causes of Engine Shaking Faults?

Here are the causes of engine shaking faults: 1. Shaking caused by engine mechanical components: The engine continuously wears during operation, and the gap between the cylinder wall and the piston will also become larger. However, the degree of wear in each cylinder may not be the same. During cold starts, the lubrication effect of the engine oil is relatively poor, and the gap between the cylinder and the piston may leak some high-temperature gas, leading to unstable cylinder operation and a certain reduction in power output. The cost of detection and repair is also relatively high. 2. Abnormal water temperature sensor: The operating condition of the engine is usually judged by the water temperature sensor. If the sensor transmits incorrect information (usually manifested as a significant difference between the transmitted temperature and the actual external temperature), it can cause abnormal fuel injection by the engine's fuel injector, making shaking problems inevitable.
1
1
Share

Reasons for Water from Car Air Conditioning Flowing into the Car

Reasons for water from car air conditioning flowing into the car: 1. Incorrect installation of the drain pipe: Cars have a dedicated air conditioning drain pipe located in the right front footwell area, with the outlet also on the right side of the car. If the drain pipe is incorrectly installed after the dashboard is removed and reassembled at a repair shop, water can flow into the car. A common symptom is water stains on the right front floor mat. 2. Internal blockage of the evaporator: For new cars, the evaporator might be internally blocked. If the evaporator's drain outlet was not properly treated during manufacturing, there might be a rubber film covering the drain outlet, preventing water from draining. 3. Poor connection: Another reason could be the evaporator's drain outlet connector, where the connected rubber drain pipe might have come off or is not properly connected.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.