How Long to Wait for a Subject 2 Retake?

1 Answers
VeraLee
07/30/25 6:33am
You need to wait 10 days before scheduling a retake. Here is some extended information about the driver's license test: 1. Subject 1: Road traffic safety laws, regulations, and related knowledge test. It is a written test conducted on a computer, with a full score of 100. A score of 90 or above is considered a pass (including 90). 2. Subject 2: Field driving skills test. It is a practical test conducted in a vehicle within a designated area, with only pass or fail results. The test includes five mandatory tasks performed in sequence: reversing into a parking space, parallel parking, S-curve driving, right-angle turning, and hill start and stop. The full score is 100, and a score of 80 or above is considered a pass (including 80). 3. Subject 3: Road driving skills test. It is a practical test conducted on a road or simulated course. The full score is 100. For large buses, a score of 90 or above is required to pass; for large trucks, 80 or above; and for other vehicle types, 70 or above. 4. Subject 4: Safe and civilized driving knowledge test. It is a written test with a full score of 100. A score of 90 or above is considered a pass (including 90).
Was this review help?
9
0
Share
More Forum Discussions

Where is the rear seat belt buckle located?

Rear seat belt buckles are typically located on the inner side of the seat or embedded in recessed areas of the seat. Some vehicles have shorter buckles designed to be concealed within the gap where the rear seat cushion and backrest meet - simply pull it out when found. If unable to locate, refer to the vehicle's owner's manual which will indicate its position. Seat belts serve as the sole safety protection for drivers, functioning as proactive safety measures that can be lifesaving in critical moments. Even during low-speed driving, collisions or emergency braking can generate sufficient inertial force to render occupants unable to control their bodies, potentially causing injuries from impact with rigid components like steering wheels or windshields.
12
0
Share

How to Set the Cruise Control on the Tiggo 3?

To set the cruise control on the Tiggo 3: After the system is activated and the vehicle reaches the desired speed, press the SET button to maintain that speed. Once the cruise speed is set, you can accelerate normally by pressing the throttle. When you release the throttle, the system will restore the vehicle speed to the preset cruise speed. The Tiggo 3 is a compact SUV under the Chery brand, with body dimensions of 4420mm in length, 1760mm in width, and 1670mm in height, and a wheelbase of 2510mm. In terms of power, the Tiggo 3 is equipped with two engines: a 1.5L naturally aspirated engine and a 1.6L naturally aspirated engine.
14
2
Share

What Does Brake System Failure Include?

Brake failure refers to the loss of braking function. Below is a detailed introduction to the contents of brake failure: Complete Failure: There is no braking effect at all, caused by faults in the brake system. This mainly occurs when the brake system cannot apply sufficient braking force to the vehicle. Reasons include insufficient brake fluid level or air ingress in the brake lines, failure of the brake control system, and various other factors that prevent the brakes from functioning properly. Partial Failure: During normal use of the vehicle, its main systems or components may experience a complete loss of specified functions or a severe decline in main performance due to quality issues. This results in a partial loss of braking effectiveness, where the brakes are less responsive or the stopping distance is significantly longer, making it difficult to stop the vehicle within a short distance. Below is additional information on brake failure:
14
1
Share

How to Determine if the Front of the Car is Not Crossing the Line?

Determining whether the front of the car is crossing the line relies on reference points on the ground and those on the car itself. Drivers can use the rearview mirror on the driver's side door and the lines on the ground as reference points to judge whether the car is crossing the line. At intersections with traffic lights, there are usually many lines on the ground. When drivers see the red light and begin to slow down, they can quickly glance at the lines on the ground, turn the steering wheel one full turn to the left plus 45 degrees, and then keep the rearview mirror aligned with the solid white line while moving forward. While driving, continue to observe whether the rearview mirror remains aligned with the solid white line. If the direction deviates, make timely corrections: turn the steering wheel to the left if the rearview mirror is outside the white line, and turn it to the right if the rearview mirror is inside the white line.
11
5
Share

How to Open the Hood of a Camry?

Method to open the hood of a Camry: The switch is located inside the car and needs to be manually operated. The switch is positioned to the left of the foot pedal; pressing it will release the outer hood. The Camry is a mid-size sedan under GAC Toyota, with dimensions of 4885mm in length, 1840mm in width, and 1455mm in height, a wheelbase of 2825mm, front-engine front-wheel drive, and a fuel tank capacity of 50 liters. In terms of exterior design, the Camry features a large trapezoidal grille with horizontal bars, a streamlined body posture, a lower waistline, an extended rear roofline that enhances rear headroom, and a dual-sided quad-exhaust tailpipe design.
9
3
Share

What are the symptoms of a damaged rear wheel bearing in a car?

When the car is moving, the wheels wobble and the overall vehicle vibration increases. Below is a detailed explanation of the symptoms of a damaged rear wheel bearing: Methods to determine if it is damaged: You can accelerate the car and then coast in neutral. If the humming sound does not change, it indicates a damaged rear wheel bearing. Causes of rear wheel bearing damage: Damage or rust on components, the entry of foreign objects, or misalignment of the roller tracks can cause damage. Prolonged exposure to acidic liquids or moisture can also lead to rust on components; poor lubrication—if there is insufficient grease between the rollers and the raceway, dry friction can occur, resulting in metallic friction noises; spacing issues—there should be appropriate gaps between car parts. If the distance between the rollers and the raceway decreases, it can lead to friction, overheating, and bearing seizure.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.