···
Log in / Register

How long is the time interval between scheduling Subject 2 and Subject 3?

4 Answers
Kendall
07/29/25 5:27pm
The normal time interval between scheduling Subject 2 and Subject 3 is about 7 to 10 days. If the Subject 2 test of the motor vehicle driver's license is not passed, the scheduling time for Subject 3 will be extended by 7 to 10 days. The process of the Subject 3 test is as follows: Changing lanes: After hearing the voice prompt, turn on the left turn signal, glance at the left rearview mirror, wait for the turn signal to flash for more than 3 seconds, and then steer the wheel to change to the left lane when it is safe. After the vehicle is straight, reset the turn signal. Left turn: After hearing the voice prompt, turn on the left turn signal, wait for it to flash for 3 seconds, and then safely pass the intersection under normal green light conditions. After turning, enter the right lane of the intersection, and reset the turn signal after the vehicle is straight.
Was this review help?
16
0
Share
LaGriffin
08/14/25 8:24am
After passing the Subject 2 test, the waiting period to schedule Subject 3 is generally around 10 to 15 days, depending on local regulations. I remember when I got my driver's license in Beijing, I had to wait a full two weeks, as this allows trainees time to practice and prepare for the road test. The duration varies significantly between cities—Shanghai might require 10 days, while Shenzhen sometimes has longer waits of up to three weeks. Don't relax too much after passing Subject 2; use this time to take more mock tests, review traffic signs and rules, and prepare thoroughly for Subject 3. Also, note that online scheduling is now convenient, so book your slot early on the platform. Your driving school can help you stay updated on policy changes. Remember, planning this period wisely can save a lot of hassle—don’t wait until the last minute to rush your preparation. Safety comes first, and thorough preparation is always the right approach.
Was this review help?
2
5
Share
Expand All
VonJocelyn
10/13/25 7:02am
Hey, there's no fixed standard for the waiting time between Subject 2 and Subject 3 scheduling. It usually starts from 10 days, but I heard from friends that in places like Hangzhou, it can be done in just a week. I once waited for half a month, during which I kept practicing driving and doing test questions non-stop. The efficiency of the driving school also affects the wait—if there are many people, the schedule might stretch to three weeks. Don't just wait; use the interval to get more hands-on road practice, familiarize yourself with the test routes, and reduce the risk of failing. It's advisable to consult your instructor right after passing Subject 2—they can give you the exact date. Download a driving test app to practice question banks and sharpen your reaction speed. A reasonable interval helps boost confidence; don't let it go to waste. Performing well in the test is what really matters.
Was this review help?
13
0
Share
Expand All
JulietteDella
11/26/25 8:02am
After passing Subject 2, the interval before booking Subject 3 generally ranges around 10 working days, with slight policy variations across regions. In practice, contacting your driving school is the most reliable approach—they'll inform you of the exact duration based on local vehicle administration arrangements. Utilize this period to enhance driving skills, such as practicing lane changes, parking, and other road test items. From my exam experience, Beijing requires 14 days, while smaller cities may mandate 10 days. Don’t just wait idly; proactively study theory and simulate real-road conditions to boost pass rates. A reasonable interval ensures safe training—don’t underestimate its importance. Confirm dates early and take action promptly.
Was this review help?
4
4
Share
Expand All
More Forum Discussions

Is a 2013 car exempt from inspection this year?

2013 vehicles require annual inspection in 2020. Below is relevant information about vehicle inspection: 1. Vehicle Annual Inspection: This refers to the annual examination conducted according to the 'Technical Conditions for Motor Vehicle Operation Safety' for vehicles that have already obtained official license plates and registration certificates. The purpose is to check the main technical conditions of the vehicle, encourage enhanced vehicle maintenance, ensure the vehicle remains in good condition, and guarantee driving safety. 2. Penalty Regulations: (1) According to relevant traffic laws, vehicles without annual inspection are not qualified to be on the road. If such vehicles continue to operate, they will be subject to a penalty of 3 demerit points and a fine of 200 RMB if caught. (2) For any traffic accidents caused by vehicles that have not undergone the annual inspection on time, the responsible party will bear all or primary liability, and the insurance company will not assume any responsibility. Since the insurance policy specifies that vehicles with expired inspections are among those excluded from coverage, in the event of an accident involving such a vehicle, all liabilities fall on the responsible party, and the insurance company has the right to refuse compensation.
19
0
Share

Can a Bubbled Tire Still Be Used?

Tires with bubbles or bulges should not continue to be used, as bulging tires are prone to blowouts, compromising driving safety. Here are the relevant details: Tire Bulges: These primarily appear on the tire sidewalls and are mainly caused by the tire violently hitting curbs, large rocks, speed bumps, etc., leading to the breakage of the tire's cord layers. If a tire bulge persists for a long time, combined with exposure to high temperatures and high-speed driving, it can easily result in a blowout, which is extremely dangerous. Wear Indicators: Tires have wear indicators; there are triangular marks on the sidewalls, and when the wear reaches the point indicated by the triangle, replacement is recommended. Inside the tire's tread grooves, there are also raised markers—when the wear reaches these raised markers at the tire's surface, it's time to replace the tire. Simple punctures can be repaired without needing replacement, but bulges must be replaced.
15
0
Share

What Causes Gear Shifting Jerkiness in Cars?

Automatic transmission jerking during gear shifts may be caused by: clutch pressure loss in the transmission; blocked or poor flow in transmission oil passages; incorrect transmission fluid level; or damaged solenoid valves. The engine's power is transmitted through the transmission, which is also a key factor affecting fuel consumption. Generally, automatic transmissions consume 10% more fuel than manual transmissions. Whether manual or automatic, more gears typically mean better fuel efficiency. Solutions for gear shifting jerkiness in automatic transmission cars: Clutch pressure loss inside the transmission. Inspect for clutch damage and perform repairs. Blocked or poor flow in transmission oil passages. This can be due to worn oil passage plates, deteriorated transmission fluid from lack of changes (reducing lubrication), or excessively dirty transmission filters allowing metal particles into the valve body. Clean the transmission oil passages. Incorrect transmission fluid level. Check whether the transmission fluid meets the standard level. Both insufficient and excessive fluid can cause this issue. For vehicles with a transmission dipstick, check the level with the engine running and adjust if necessary. Damaged solenoid valves. Sludge buildup circulating in the transmission can block oil passages in the valve body, causing jerking. Over time, this leads to transmission overheating, harsh shifting, slippage, and other issues. Replace the solenoid valves if needed.
17
2
Share

Are There Fake Tires?

Tires can be counterfeit, and retreaded tires are considered fake tires. Methods to distinguish between genuine and fake tires: Observe the color and gloss of the tire: Retreaded tires tend to have duller colors and less gloss, and the tire body is rougher. Press the tire tread: Retreaded tires often have a layer of wax on the tread, which will leave fingerprints when touched, whereas new tires will not leave fingerprints when pressed. Identify through the markings on the tire: Car tires have raised markings indicating the tire model and performance. Generally, the markings on retreaded tires are reattached after retreading, while the markings on brand-new tires are integrated with the tire. A method to identify is to scratch these markings with a fingernail—if the markings can be peeled off, they are undoubtedly from a retreaded tire. Car tires are a crucial component of a vehicle, and their quality directly determines the safety performance and driving speed. Nowadays, there are numerous brands of car tires. Good-quality tires can ensure driving safety and improve speed, but there are also many counterfeit products in the market. Fake tires not only significantly reduce driving comfort but also pose safety risks and potential accidents. This requires car owners and users to know how to distinguish between genuine and fake tires to avoid being deceived by counterfeit sellers.
6
4
Share

What Causes the Car to Shake When Driving at 80 MPH?

The shaking experienced when driving above 80 MPH may be caused by issues such as a damaged clutch pressure plate spring, worn or damaged tires, or a bent drive shaft or half-shaft. Damaged Clutch Pressure Plate Spring: A damaged clutch pressure plate spring leads to an unbalanced pressure surface, causing shaking during transmission and resulting in overall vehicle vibration. Bent Half-Shaft: The half-shaft of a car is a solid axle that transmits torque between the differential and the drive wheels. Its inner end is typically connected to the half-shaft gear via splines, while the outer end connects to the wheel hub. Modern vehicles commonly use two types of half-shafts based on their support type: full-floating and semi-floating. The half-shaft is horizontal, while the tire is vertical. A bent half-shaft causes instability when transmitting lateral torque, leading to tire wobble and overall vehicle shaking. If the half-shaft is bent, it must be replaced—either the CV joint alone or the entire half-shaft assembly. Symptoms of a bent half-shaft include severe shaking and pulling at high speeds, unusual noises when turning the steering wheel fully left or right, metallic scraping or clunking sounds while driving, and uneven tire wear.
18
1
Share

Why does the window make noise when it reaches the top?

This may be due to friction between the stopper or the rubber seal and the glass. Solutions for scratches on the window glass are as follows: 1. Polishing or repair agent: Scratches caused by cleaning are generally small, so you can use polishing to smooth them out or use a repair agent for restoration. 2. Using toothpaste: Toothpaste can repair some minor scratches. Apply an appropriate amount of toothpaste to the scratched area of the window glass, wipe it with a cotton cloth, and then rinse it with water. 3. Visit a repair shop: If the scratches are deep, it is best to go to a professional repair shop for treatment to achieve the best results.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.