How Long is the Engine Warranty for the Bin Yue?

1 Answers
DeValeria
07/29/25 8:25pm
The engine warranty for the Bin Yue is 8 years or 300,000 kilometers. Here is some related information: An engine is a machine that can convert other forms of energy into another type of energy, usually converting chemical energy into mechanical energy. The Geely JLF3G10TD three-cylinder 1.0T engine is equipped with mainstream top-mounted direct injection technology, which provides better fuel atomization and more complete combustion. At the same time, this engine also features dual variable valve timing technology, an integrated exhaust manifold, and a vacuum pressure relief valve. The engine in the Geely Bin Yue delivers a maximum power of 177 PS and a peak torque of 255 Nm, paired with a 7-speed wet dual-clutch transmission.
Was this review help?
5
2
Share
More Forum Discussions

Why Are High-View Vehicles Not Practical?

High-view vehicles are not practical due to their low configurations and incomplete functionality. Here is a partial introduction about automotive power: Calculation formula: Power P = Speed V * Traction Force F. Therefore, the product of F and V determines the vehicle's power. The vehicle's power determines its speed, while torque determines its acceleration. Rated power: Rated power refers to the power when an electrical appliance operates normally. Its value is the rated voltage of the appliance multiplied by the rated current. If the actual power of the appliance is greater than the rated power, the appliance may be damaged; if the actual power is less than the rated power. Relationship between power and speed: Under normal operating conditions, the output power of a power device or the input power of an energy-consuming device. It is often measured in "kilowatts." It also refers to the power that a machine produced in a factory can achieve during normal operation. That is, the commonly referred power of a machine. The rated power of a machine is constant, P=Fv, so the force generated by the machine is inversely proportional to its operating speed. For example, when a car is driving on a flat asphalt road, the required traction force F is smaller, allowing for higher speeds; when the road is uneven or going uphill, a larger traction force is required, necessitating a switch to lower speeds.
2
1
Share

Which gear should be used when driving at 30 mph?

Start the car in 1st gear below 10 mph, and shift to 2nd gear once moving. When the speed exceeds 20 mph in 2nd gear, shift to 3rd gear. 3rd gear is suitable for speeds above 20 mph but below 40 mph, while 4th gear requires reaching 40 mph. 5th gear is for high-speed driving, typically above 60 mph. Shifting gears is not solely based on speed but rather on engine RPM. Generally, when in 4th gear, if the engine RPM exceeds 2000, you can shift to 5th gear. If the engine sounds sluggish, it indicates that the engine is struggling to move the car, and you should downshift to increase engine torque. Conversely, if the engine is whining, you should upshift to reduce engine torque at the same speed. For cars with a displacement of 1.3 liters or more, during acceleration, it is best to shift to 5th gear at a speed of 70–75 km/h. Shifting at this speed ensures that the engine RPM remains between 2000–3000 RPM before and after shifting, balancing both power and fuel efficiency. Shifting below this RPM significantly affects performance due to the power-RPM characteristics of modern car engines.
19
1
Share

How to Find the Clutch Half-Engagement Point?

Finding the clutch half-engagement point involves the following steps: 1. As the clutch is lifted to the half-engagement point, the car will transition from stationary to moving with a noticeable vibration. Lightly resting your hands on the steering wheel will allow you to feel this vibration; 2. When the engine sound begins to change and the vehicle experiences a slight vibration, the clutch pedal will also give a slight resistance against your foot, indicating that the clutch is at the half-engagement point; 3. Observe the engine tachometer on the dashboard. When the engine RPM drops significantly during the process of lifting the clutch, it means the clutch has reached the half-engagement point; 4. When the clutch is lifted to the half-engagement position, the vehicle will have a slight forward surge, indicating that the clutch is at the half-engagement point.
13
1
Share

Should You Press the Accelerator When Shifting Gears in a Manual Transmission?

1. When upshifting. For manual transmission cars when upshifting, you should first release the accelerator, then quickly press the clutch and shift gears rapidly. Of course, you can also press the clutch while releasing the accelerator. If you press the clutch first and then release the accelerator, it will cause the engine to run without load, producing a roaring sound, which not only wastes fuel but also increases noise. 2. When downshifting. For manual transmission cars when downshifting, you should first apply the brakes to reduce the speed, then press the clutch, followed by a quick gear shift. When downshifting, it is necessary to reduce the speed, so there is no need to press the accelerator. When shifting gears in a manual transmission car you need to master the speed of releasing the clutch. In lower gears, such as shifting from first to second gear, second to third gear, or downshifting from third to second gear, second to first gear, you should let the clutch stay at the semi-engaged position for a moment before fully releasing it. This way, the vehicle will not experience jerking during driving. Driving a manual transmission car, the most crucial technique is the coordination between the accelerator and the clutch. Mastering this coordination means you have grasped the essence of driving a manual transmission car, making your driving smoother and more fluid.
16
1
Share

Can a C1 License Drive an Electric Tricycle?

C1 driver's license can drive electric tricycles. Permitted vehicle types for C1 license: The permitted driving scope of a C1 driver's license includes small and mini passenger vehicles, light and mini cargo vehicles; light, small, and mini special purpose vehicles; small passenger vehicles with seating capacity less than or equal to 9 people. C1 driver's license cannot drive: large buses, tractor units, city buses, medium buses, large trucks, ordinary three-wheeled motorcycles, ordinary two-wheeled motorcycles, light motorcycles, wheeled self-propelled machinery, trolleybuses, and tramcars. Additionally, a C1 license cannot drive vehicles with more than 9 seats, nor can it drive trucks with a total length exceeding 6 meters. Passing standards for C1 license test: Traffic regulations and related knowledge (Subject 1) - written test, full score of 100, passing score is 90 or above. Field driving (Subject 2) - on-site, actual vehicle. Minimum passing score is 80, below 80 is failing. Road driving (Subject 3) - highway or simulated field, actual vehicle. Full score is 100, must achieve 90 or above to pass. Safe and civilized driving knowledge - written test, questions mainly in the form of cases, pictures, animations, etc., question types include true/false, single choice, and multiple choice, total of 50 questions, full score of 100, passing score is 90.
11
5
Share

How to Check the Tire Pressure Monitoring in GLA?

gla tire pressure monitoring can be checked by: locating the desired tire pressure data through the multifunction buttons on the steering wheel. Taking the 2020 GLA as an example, it belongs to the compact SUV category, with body dimensions of: length 4427mm, width 1834mm, height 1610mm, and a wheelbase of 2729mm. The 2020 GLA features a MacPherson independent front suspension and a multi-link independent rear suspension. It is equipped with a 1.3L turbocharged engine, delivering a maximum horsepower of 136PS, maximum power of 100kW, maximum torque of 250Nm, paired with a 7-speed dual-clutch transmission.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.