How long is the battery warranty for the Trumpchi GS4?

1 Answers
LaKai
07/30/25 6:13am
The battery warranty period for the Trumpchi GS4 is one year. Within this one-year period, any quality issues will result in a free replacement. Car batteries are sensitive to low temperatures—under cold conditions, a battery's capacity is significantly lower than at normal temperatures. Therefore, regular inspection and maintenance are essential. Daily care tips include: 1. Avoid parking the car in open-air parking lots for extended periods. If long-term parking is unavoidable, remove the battery to prevent freezing damage. 2. In winter, car engines are harder to start. Each attempt to start the engine should not exceed 5 seconds, with at least a 15-second interval between attempts. If the engine fails to start after several tries, check other potential issues like the electrical circuit, ignition coil, or fuel system. Avoid continuous unsuccessful starts, as this can over-discharge and damage the battery. 3. Regularly charge the car battery. A battery left unused will gradually self-discharge and eventually become unusable. Thus, start the car periodically to recharge the battery. 4. Clean the battery terminals periodically and apply specialized grease to protect the wiring harness. Routinely inspect the battery's components and connections. 5. Avoid using car electronics when the engine is off. Using the battery alone without the engine generating power can cause harm.
Was this review help?
2
3
Share
More Forum Discussions

Do I Need to Replace Brake Fluid When Changing Brake Discs?

Replacing brake discs does not require changing the brake fluid. There is no inherent connection between the replacement cycles of the two. Brake fluid generally needs to be replaced when its water content exceeds 4%, whereas brake discs do not have a fixed replacement interval. The recommended replacement cycle for brake fluid is every 2 years or 40,000 kilometers. Introduction to Brake Fluid: Brake fluid is also known as hydraulic brake fluid. It has a specific water content ratio, and when the water content becomes too high, it must be replaced promptly. Brake fluid naturally absorbs moisture, and over time, water from the air can seep into the brake fluid reservoir through the vent hole, leading to excessive water content in the brake fluid. Function of Brake Fluid: It effectively lubricates the moving parts of the braking system, extending the service life of brake calipers and rubber cups.
2
0
Share

How to Replace the Headlight Bulb of Mazda Axela?

The method to replace the headlight bulb of Mazda Axela is: 1. Unplug the power connector of the bulb and remove the waterproof cover behind the bulb; 2. Take out the bulb from the reflector and replace it with a new one. The Mazda Axela is a compact 4-door 5-seater sedan with a body size of 4662mm in length, 1797mm in width, 1445mm in height, and a wheelbase of 2726mm. The Mazda Axela is equipped with a 1.5L naturally aspirated engine and a 6-speed manual transmission, delivering a maximum power of 86 kW and a maximum torque of 148 Nm. It features front-wheel drive, with a MacPherson strut independent front suspension and a torsion beam non-independent rear suspension.
10
5
Share

What to Do When BMW X6 Air Conditioner Fails to Start and Trunk Won't Open?

BMW X6 air conditioner fails to start and the trunk cannot be opened, which may be due to a power interruption in the car. Simply press the start button again to resolve the issue. The reasons for power interruption are as follows: 1. GPS-induced power interruption. If this is the case, it is recommended to have the GPS inspected at the installation location; 2. Incorrect wiring or poor grounding of the anti-theft device; 3. Forgetting to turn off the lights or other electrical equipment after leaving the car, resulting in battery depletion. Replacing the battery will solve the problem. Several consecutive instances of battery depletion will reduce the battery's lifespan. 4. The issue may be caused by problems with the fuse box itself or the connection between the fuse box and the wiring harness plug. The main reason may be poor contact between the pins on the fuse box socket and the internal circuits of the fuse box, or loose spring clips on the wiring harness plug.
15
2
Share

How to Reset the Maintenance Light on a Magotan?

To reset the maintenance light on a Magotan, follow these steps: 1. First, press the small wrench button on the dashboard with your left hand, then turn on the ignition with your right hand. After that, release the small wrench button with your left hand and press the minute adjustment button on the time setting. 2. Turn off the ignition, remove your left hand from the time button, and start the engine. The maintenance reminder will then disappear. Here is some related information about the Magotan: 1. The Magotan is a mid-size car launched by FAW-Volkswagen, with dimensions of 4865mm in length, 1832mm in width, and 1471mm in height, and a wheelbase of 2871mm. 2. It is equipped with either a 1.4T or 2.0T turbocharged engine, with maximum power outputs of 110kw and 137kw respectively, paired with a 7-speed dual-clutch transmission.
2
3
Share

Will oil leak if the underbody shell is broken?

In most cases, oil will not leak if the underbody shell is broken. It mainly depends on the location of the damage to the chassis. If the damaged area on the vehicle chassis contains fluid compartments, oil leakage will occur immediately after the damage. If the chassis is hit by sharp objects like protruding rocks on the road, engine oil may leak. Applying underbody armor: After the car underbody is sprayed with underbody armor, a strong elastic protective layer will form on the sprayed area. This layer not only prevents impacts from flying stones and gravel but also protects the underbody metal from moisture, acid rain, and salt corrosion, preventing the chassis from rusting. Installing an engine guard: The engine guard is a custom-designed protective device for the engine based on different vehicle models. Its primary purpose is to prevent mud from covering the engine, and secondly, to protect the engine from damage caused by impacts from uneven road surfaces during driving.
3
0
Share

What kind of adhesive is used to bond car bumpers?

Structural adhesive is used to bond car bumpers. The bumper is a safety device that absorbs and mitigates external impacts, protecting the front and rear of the vehicle body. It consists of an outer panel, cushioning material, and a crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed by stamping cold-rolled thin plates (approximately 1.5 mm thick) into a U-shaped channel. The outer panel and cushioning material are attached to the crossbeam, which is connected to the frame longitudinal beam with screws and can be easily detached. Methods for repairing bumper scratches include: 1. Apply toothpaste to shallow scratches and wipe counterclockwise with a soft cloth; 2. Spray car paint scratch repair agent onto the scratches and wipe with a towel; 3. Use a touch-up pen to spray and fill the damaged area along the direction of the scratch, then apply fine wax after it dries.
6
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.