How Long Does the Battery of a Tire Pressure Monitor Last?

2 Answers
MacAlyssa
07/28/25 7:39pm
The service life of tire pressure monitors is as follows: 1. The battery life of built-in sensors is 7-8 years. The sensors of built-in tire pressure monitors are installed inside the tires, which is relatively stable and provides more accurate monitoring data. The principle is to use pressure sensors installed in each tire to directly measure the tire pressure, then transmit the pressure information from inside the tire to a central receiver module via a wireless transmitter, and finally display the tire pressure data for each tire. 2. The battery life of external sensors is 3-5 years. They are easy to install and can be done by oneself. The measurement of tire pressure parameters is also relatively accurate, and the service life of the sensors can be extended by replacing the built-in battery later. 3. The battery of the display, when fully charged, generally lasts about 45 days.
Was this review help?
5
0
Share
VonFelicity
08/12/25 12:34am
I'm really passionate about automotive technology. The battery in a tire pressure monitor typically lasts five to ten years, depending on your driving habits and climate. Frequent driving wears the battery out faster, and extreme cold or heat speeds up aging. Usually, these are lithium batteries integrated into the wheel sensors, so replacing them is a hassle—you have to remove the tire. If the battery dies, the dashboard will show a warning light, which might falsely indicate a tire pressure issue, compromising safe driving. Remember, regular tire pressure checks can indirectly extend battery life, and minimizing system activation when not in use saves power. Once the warning light comes on, get to a repair shop ASAP to avoid delays or extra costs like tire repairs.
Was this review help?
15
0
Share
Expand All
More Forum Discussions

What is the general tire pressure for a van?

The tire pressure for a van can be selected according to the manual, around 2.5mpa is suitable. Here is the relevant content introduction: 1. Pressure: If the pressure is too low, it will increase the deformation of the tire body, and cracks are prone to appear on the sidewall. At the same time, it will cause flexing movement, leading to excessive heat, promoting rubber aging, fatigue of the cord layer, and breakage of the cords. It will also increase the tire's contact area with the ground, accelerating shoulder wear. If the pressure is too high, the tire cords will be excessively stretched and deformed, reducing the elasticity of the tire body. This will increase the load on the car while driving, and if impacted, it may cause internal cracks and explosions. Additionally, excessive pressure will accelerate crown wear and reduce puncture resistance. 2. Tire pressure: The appropriate tire pressure depends on the load and the season. If carrying cargo, it is recommended to have 3.5bar for the front tires and 4.0bar for the rear tires. If not carrying cargo, around 2.1bar in summer and 2.5bar in winter is sufficient. 3. Over-inflation or under-inflation: The tire pressure should not be too high or too low. If the pressure is too low, the tire may exhibit wave-like deformation during high-speed driving, increasing the risk of a blowout. If the pressure is too high, it will reduce the contact area between the tire and the ground, leading to decreased vehicle handling and driving stability.
7
5
Share

What are the reasons for the weak starting of the starter motor?

The reasons for the weak starting of the starter motor are: 1. Insufficient battery charge or loose connections, dirty terminals, poor contact; 2. Starter motor bushings too tight or too loose; 3. Bent or deformed armature shaft scraping against the magnetic poles; 4. Dirty commutator or brushes, worn brushes, weakened spring tension; 5. Open circuit or partial open circuit in the field coils or armature coils; 6. Burnt contacts in the starter switch. Precautions for using the car motor are: 1. Regularly clean accumulated dirt and dust on the generator surface to maintain cleanliness and good ventilation; 2. Periodically check the tightness of all fasteners related to the generator and promptly tighten all screws; 3. If the generator fails to generate electricity, troubleshoot the issue immediately.
2
5
Share

Where is the engine number located on a BMW 530?

BMW 530 engine number is located on the lower left side of the engine. Lift the car up, and there is a gap near the left front wheel where you can see it with a flashlight. The engine model consists of the front part, middle part, rear part, and tail part. It is an identification code assigned by the engine manufacturer in accordance with relevant regulations, corporate or industry practices, and the attributes of the engine, used to represent information such as the manufacturer, specifications, performance, features, craftsmanship, purpose, and product batch of the engine. The BMW 530 is equipped with a 2.0T turbocharged engine, with a maximum horsepower of 252 PS, a maximum power of 185 kW, a maximum torque of 350 Nm, and is paired with an 8-speed automatic transmission.
4
0
Share

Can I provide my own driver's license photo?

The photo on the driver's license can be brought by yourself or taken on-site. Here are the relevant details: 1. Driver's License: The full name is Motor Vehicle Driver's License, also known as "driver's license", which is the certificate required by law for motor vehicle drivers. Driving a motor vehicle requires certain driving skills, and those who lack such skills may cause traffic accidents if they drive at will. Generally, driving without a license is not allowed. 2. Photo Requirements: A straight-edged, front-facing, color passport-style photo of the applicant taken within the last 6 months before applying for the driver's license. The background should be white, and red clothing is not allowed.
14
0
Share

How many days in advance should a driver's license be renewed?

Driver's license renewal should be done 90 days in advance. According to the regulations on the application and use of motor vehicle driver's licenses: A motor vehicle driver shall apply for renewal at the vehicle management office of the place where the driver's license was issued within 90 days before the expiration of the current driver's license. When applying, the applicant must fill out an application form and submit the identity proof of the motor vehicle driver, the current driver's license, and a medical certificate issued by a county-level or above medical institution or a military medical institution at the regimental level or above. A driver's license, also known as a 'driving license,' is a document issued by the government's transportation department to individuals who are qualified to drive. It is usually a card. To obtain a driver's license, one must meet the minimum age requirement and pass a driving test.
1
0
Share

What are the requirements for the one-inch white background photo on a driver's license?

Driver's license one-inch photos must have a white background with specific requirements as follows: 1. Half-length portrait: A straight-edged, front-facing, bareheaded, color half-length ID photo of the applicant taken within 6 months prior to applying for a motor vehicle driver's license. 2. Attire: The background color must be white; red clothing is not allowed (affects stamping), women cannot wear earrings, shawl photos are not permitted during photography, men's hair should not be too long, the headshot must be clear with a natural expression. Photo dimensions should be 32mm*22mm, with head width between 14mm~16mm and head length between 19mm~22mm.
3
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.