···
Log in / Register

How long does it take to replace the front bumper at a 4S shop?

1 Answers
Ortega
09/04/2025, 12:12 AM

Replacing the front bumper at a 4S shop takes about 1 hour. The replacement method is as follows: 1. Remove the screws at the bottom of the front bumper and open the front hood; 2. Unscrew the screws on the frame and remove the bumper; 3. Loosen the bolts in the middle of the front bumper and the star-shaped screws on the wheel liner, then separate the bumper skin from the bracket; 4. Unscrew the screws under the front wheel inner liner and remove the grille emblem; 5. Unscrew the screws inside the fog light air intake grille, push the front bumper forward, and pull it off along the clips. The car bumper is a safety device that absorbs and mitigates external impacts, protecting the front and rear of the vehicle, located at the front and rear of the car.

Was this review help?
4
4
Share
More Forum Discussions

Is It Safe to Keep a Cartridge Stove Gas Canister in a Car?

Keeping a cartridge stove gas canister in a car is not safe. Here is the relevant information: Introduction: The gas inside a cartridge stove canister is flammable and explosive, and it is specified that the storage temperature should not exceed 40 degrees Celsius. In summer, the temperature inside a car can exceed 60 degrees Celsius, which can easily cause the canister to explode or catch fire if left inside the vehicle. Therefore, for the safety of the car, it is best not to store cartridge stove gas canisters in the car for extended periods. Precautions: Cartridge stoves, also known as portable butane stoves, are non-fixed cooking utensils that primarily use canned butane gas as fuel, although liquefied gas can also be used. They are directly heated by fire and are commonly used for outdoor leisure activities and hotel supplies. They are small in size and easy to carry, making them a recently popular kitchen tool often used in hotel equipment and family outdoor activities. Usage Instructions: Connect the liquefied gas canister, open its valve, and then invert it; filling for 5 to 8 minutes is sufficient. For safety during use, a safety device inside the cartridge stove is essential.
18
1
Share

How many kilometers do you need to drive for Subject 3?

Subject 3 covers a total distance of 3 kilometers. Here is the relevant information: General situation: Generally, if unexpected situations occur and some items of Subject 3 are not completed, you may need to drive more, but usually, it is up to three kilometers at most. For a C license, three kilometers is usually sufficient. For example, large buses, tractors, and city buses require a driving test distance of no less than 7 kilometers; medium-sized buses and large trucks require no less than 5 kilometers; small cars and small automatic transmission cars require no less than 3 kilometers. Notes: The Subject 3 test is relatively simple. Stay calm and think through all the routes in advance, and there should generally be no problems. Familiarize yourself with the test route map, including the locations of zebra crossings, intersections, suitable spots for the 100-meter gear shifting exercise, U-turn points, turning points, and traffic lights.
10
5
Share

What is the tire pressure for a 125cc motorcycle in bar?

Generally, the tire pressure for a motorcycle's front wheel is 170-200 kPa, and the rear wheel is 200-220 kPa. The rear tire of a motorcycle bears more load, so when checking by hand, after inflating, press firmly—it should feel slightly compressible. It's best to use a tire pressure gauge for accurate measurement. Typically, the front tire pressure ranges from 170-200 kPa, and the rear tire from 200-220 kPa. The standard tire pressure values are usually listed in the vehicle's manual. Precautions for inflating tires: Always use a pressure gauge to check the tire pressure while inflating to avoid overinflation, which could cause the tire to burst. After stopping, wait for the tires to cool down before inflating, as driving increases tire temperature and affects pressure. Check the valve stem. If the valve stem and valve core are not aligned properly, with protrusions, depressions, or other defects, it may hinder inflation and pressure measurement. Maintain cleanliness during inflation. The air being pumped in should not contain moisture or oil, as this can deteriorate and damage the inner tube rubber.
19
0
Share

Is the Subject 2 Test Easy to Pass?

Subject 2 test is not easy to pass. Here is some relevant information: Reasons: Nervousness, feeling tense during the test is a common issue for many people. Life is full of various tests, and there's no need to put too much pressure on yourself. If you fail, you can always try again. Only by relaxing your mind can you perform better. Carelessness, many people tend to rush, leading to impatience during the test. This impatience often results in forgetting to turn on the signal lights or fasten the seatbelt, etc. Excessive speed, for beginners, driving too fast during the test is a major reason for failure. High speed makes it difficult to react promptly when mistakes occur. Unfamiliarity with the Subject 2 test site, for first-time license applicants, there are always some differences between the practice field and the test site. Therefore, it's important to communicate more with the coach during training to understand these differences and enhance simulation practice. Test experience: Depending on the region, test regulations may vary slightly. Some regions offer a free simulation test before the actual exam, with all standards based on the test requirements. It's crucial to make good use of this training opportunity to avoid panic during the real test. Some regions provide two chances. In such cases, if you fail the first time, learn from the experience, understand your mistakes, and correct them in the second attempt.
2
5
Share

Can I Go Back to Change Answers in Subject One Exam?

During the Subject One exam, you cannot go back to change answers. Once you proceed to the next question, the system will immediately display whether the previous answer was correct or incorrect. If correct, there will be no prompt; if incorrect, it will be automatically shown. Subject One Exam Content: Basic knowledge of motor vehicles; laws, regulations, and road traffic signals; fundamentals of safe and civilized driving; basic knowledge related to motor vehicle operation. Subject One Passing Score: The total duration of the Subject One exam is 45 minutes. The test consists of 100 questions, including true/false and multiple-choice questions, with a maximum score of 100 points. A score of 90 or above is required to pass. The exam questions are randomly selected and combined by the computer-based driver examination system according to the proportion specified in the "Motor Vehicle Driver's License Work Regulations." Subject One Exam Attempts: There is no limit to the number of attempts for Subject One. Each exam session offers two chances. If both attempts fail, you will need to reschedule the exam.
13
2
Share

Can I use a temporary ID if I lost my ID card for Subject 2 exam?

A temporary ID can be used for the Subject 2 exam. However, if you need to use a temporary ID due to the absence of your original ID, you must inform the driving test instructor in advance and follow the arrangements made by the driving school. According to Article 19, Paragraph 1 of the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," "first-time applicants for a motor vehicle driving license shall fill out an application form and submit their identity proof." Therefore, you can use a temporary ID to take the Subject 2 exam. Additionally, it is important to note that a temporary resident ID is valid for three months. You can take the Subject 2 exam within this validity period, but you will not be allowed to enter the exam venue if the ID has expired. Therefore, make sure to take the exam within the validity period. If the temporary ID expires due to special circumstances, you should promptly apply for a replacement of either a formal ID or a new temporary ID. Subject 2, also known as the small road test, is part of the motor vehicle driving license assessment and refers to the field driving skills test. For small vehicles (C1/C2), the exam includes five mandatory items: reversing into a parking space, parallel parking, stopping and starting on a slope, turning at a right angle, and driving through curves (commonly known as the S-curve). Some regions may have a sixth item, such as high-speed card collection. According to Article 25 of the "Regulations on the Application and Use of Motor Vehicle Driving Licenses" (Ministry of Public Security Order No. 123), as of June 1, 2021, the stopping and starting on a slope item is no longer required for C2 and C5 license exams. For large vehicles (AB licenses), Subject 2 includes 16 items: reversing into a parking space, passing through continuous obstacles, driving through curves, simulated highway driving, passing through a narrow gate, driving on undulating roads, driving on a single-plank bridge, making a U-turn on a narrow road, stopping and starting on a slope, parallel parking, handling emergencies on highways, simulated mountain driving, turning at a right angle, simulated rain and fog conditions, handling a tire blowout on highways, and simulated tunnel driving.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.